Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255601 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1675/18  Rear Floor Airbag Sensor Malfunction  


DESCRIPTION

The rear floor airbag sensor consists of the diagnostic circuit, the rear floor deceleration sensor, etc.

If the center airbag sensor receives signals from the rear floor deceleration sensor, it determines whether the SRS should be activated.

DTC B1675/18 is stored when a malfunction is detected in the rear floor airbag sensor circuit.

DTC Code DTC Detection Condition Trouble Area
B1675/18 When one of the following conditions is met:
·

A rear floor airbag sensor malfunction.

·

A center airbag sensor malfunction.


·

Rear floor airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C148443E44
1.219,1.344 1.635,1.5 0.417,0.156 10 false BFR+ 1.24,2.698 1.656,2.854 0.417,0.156 10 false BFR- 5.688,1.365 6.104,1.521 0.417,0.156 10 false BDR+ 5.688,2.677 6.104,2.833 0.417,0.156 10 false BDR- 1.677,1.24 1.833,1.385 0.156,0.146 10 false 2 1.688,2.552 1.844,2.719 0.156,0.167 10 false 1 5.385,1.26 5.604,1.417 0.219,0.156 10 false 21 5.365,2.583 5.604,2.74 0.24,0.156 10 false 22 0.271,3.823 0.594,4.01 0.323,0.188 10 false L19 0.281,4 2.073,4.24 1.792,0.24 10 false Rear Floor Airbag Sensor 5.448,3.813 5.885,4 0.438,0.188 10 false L27 5.448,3.969 6.875,4.135 1.427,0.167 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION ).

·

After replacing the center airbag sensor assembly, refer to initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK REAR FLOOR AIRBAG SENSOR
a.
C171812E02
0.458,1.221 1.405,1.566 0.948,0.346 10 Rear Floor Airbag Sensor 1.754,1.055 2.660,1.382 0.906,0.327 10 Center Airbag Sensor

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Temporarily replace the rear floor airbag sensor with a new one.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1675 is not output.


HINT:

Codes other than DTC B1675 may be output at this time, but they are not related to this check.




C

A

B