Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255605 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


PROCEDURE

Hide 84306 1.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B459544C01
1.667,1.656 2.073,1.979 0.406,0.323 5.125,1.625 5.531,1.948 0.406,0.323 3.292,3.365 3.698,3.688 0.406,0.323 1.583,1.177 1.104,0.813 true 1.552,1.25 1.021,1.25 true 5.021,1.417 5.021,1.26 5.021,1.26 4.438,1.26 true 5.052,1.531 4.073,1.667 true 4.74,2.677 4.333,3.24 true 4.896,3.479 4.302,3.479 4.302,3.479 4.302,3.313 true 1.844,0.365 2.219,0.604 0.375,0.24 12 false *A 5.323,0.375 5.698,0.615 0.375,0.24 12 false *B 3.771,2.365 4.146,2.604 0.375,0.24 12 false *C 0.948,0.677 1.198,0.844 0.25,0.167 10 false *a 3.917,1.594 4.167,1.76 0.25,0.167 10 false *a 4.292,1.188 4.542,1.354 0.25,0.167 10 false *d 0.854,1.156 1.104,1.323 0.25,0.167 10 false *c 1.677,1.667 1.875,1.854 0.198,0.188 10 true *b 5.135,1.635 5.333,1.823 0.198,0.188 10 true *b 3.302,3.375 3.49,3.563 0.188,0.188 10 true *b 4.917,3.375 5.167,3.542 0.25,0.167 10 false *d 4.75,2.542 5,2.708 0.25,0.167 10 false *a 2.469,3.958 2.844,4.198 0.375,0.24 12 false *D 3.823,4.563 4.198,4.802 0.375,0.24 12 false *E
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type), w/o Steering Heater
*C Flat Cable (Visible Type), w/ Steering Heater *D for Type A
*E for Type B - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn



b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459545C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B459546

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459547C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B459544C01
1.667,1.656 2.073,1.979 0.406,0.323 5.125,1.625 5.531,1.948 0.406,0.323 3.292,3.365 3.698,3.688 0.406,0.323 1.583,1.177 1.104,0.813 true 1.552,1.25 1.021,1.25 true 5.021,1.417 5.021,1.26 5.021,1.26 4.438,1.26 true 5.052,1.531 4.073,1.667 true 4.74,2.677 4.333,3.24 true 4.896,3.479 4.302,3.479 4.302,3.479 4.302,3.313 true 1.844,0.365 2.219,0.604 0.375,0.24 12 false *A 5.323,0.375 5.698,0.615 0.375,0.24 12 false *B 3.771,2.365 4.146,2.604 0.375,0.24 12 false *C 0.948,0.677 1.198,0.844 0.25,0.167 10 false *a 3.917,1.594 4.167,1.76 0.25,0.167 10 false *a 4.292,1.188 4.542,1.354 0.25,0.167 10 false *d 0.854,1.156 1.104,1.323 0.25,0.167 10 false *c 1.677,1.667 1.875,1.854 0.198,0.188 10 true *b 5.135,1.635 5.333,1.823 0.198,0.188 10 true *b 3.302,3.375 3.49,3.563 0.188,0.188 10 true *b 4.917,3.375 5.167,3.542 0.25,0.167 10 false *d 4.75,2.542 5,2.708 0.25,0.167 10 false *a 2.469,3.958 2.844,4.198 0.375,0.24 12 false *D 3.823,4.563 4.198,4.802 0.375,0.24 12 false *E
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type), w/o Steering Heater
*C Flat Cable (Visible Type), w/ Steering Heater *D for Type A
*E for Type B - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 2.INSTALL SPIRAL CABLE

NOTICE:
·

Do not replace the spiral cable sub-assembly with the auxiliary battery connected and the power switch on.

·

Do not rotate the spiral cable sub-assembly with the auxiliary battery connected and the power switch on.

·

When rotating the spiral cable sub-assembly to check the operation of the spiral cable sub-assembly (checking for abnormal noise, checking the DTC, Data list, etc.) make sure to perform the inspection with the steering wheel assembly installed.

·

If the steering sensor is installed to a misaligned spiral cable, DTCs for an abnormal steering sensor value such as DTC C1231, C1290 are stored and it is impossible to repair them. If this happens, replace the spiral cable sub-assembly with a new one.

·
B262558C06
0,0 0,0 false
V100135

Lock Pin


When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



a.
B449538E01
1.458,0.333 1.813,0.49 false 2.531,0.958 2.594,1.604 false 1.219,0.208 1.594,0.427 0.375,0.219 10 false Pin 2.531,1.615 2.906,1.833 0.375,0.219 10 false Pin

Align the pins on the spiral cable with the installation holes on the steering sensor.


b.

Attach the 6 claws to install the spiral cable to the steering sensor.


c.

Check that the power switch is off.


d.

Check that the cable is disconnected from the auxiliary battery negative (-) terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.



e.

Check that the front wheels are facing straight ahead.


f.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.



g.
B181593

Attach the 3 claws to install the spiral cable sub-assembly.


h.

Connect the connectors to the spiral cable with steering sensor.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 5.ADJUST SPIRAL CABLE

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the auxiliary battery negative (-) terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.



c.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B459548C01
1.917,1.281 2.281,1.615 0.365,0.333 5.281,1.313 5.635,1.594 0.354,0.281 2.99,3.323 3.354,3.615 0.365,0.292 0.833,1.625 0.479,1.094 true 0.781,1.875 0.49,2.417 true 4.427,1.854 4.844,2.26 true 3.719,1.156 4.063,1.156 4.063,1.156 4.302,1.708 true 4.865,3.635 5.292,3.219 true 4.76,3.865 4.76,4.5 4.76,4.5 5.115,4.5 true 2.01,0.208 2.385,0.448 0.375,0.24 12 false *A 5.385,0.229 5.76,0.469 0.375,0.24 12 false *B 3.354,2.354 3.729,2.594 0.375,0.24 12 false *C 2.25,3.802 2.625,4.042 0.375,0.24 12 false *D 3.542,4.406 3.917,4.646 0.375,0.24 12 false *E 0.344,0.938 0.656,1.135 0.313,0.198 10 false *a 1.927,1.281 2.115,1.438 0.188,0.156 10 true *b 5.292,1.313 5.479,1.469 0.188,0.156 10 true *b 3,3.323 3.188,3.479 0.188,0.156 10 true *b 0.406,2.448 0.719,2.646 0.313,0.198 10 false *c 4.865,2.188 5.177,2.385 0.313,0.198 10 false *a 5.323,3.115 5.635,3.313 0.313,0.198 10 false *a 5.146,4.396 5.458,4.594 0.313,0.198 10 false *d 3.563,1.063 3.875,1.26 0.313,0.198 10 false *d
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type), w/o Steering Heater
*C Flat Cable (Visible Type), w/ Steering Heater *D for Type A
*E for Type B - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn



d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459549C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B459550

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459551C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B459548C01
1.917,1.281 2.281,1.615 0.365,0.333 5.281,1.313 5.635,1.594 0.354,0.281 2.99,3.323 3.354,3.615 0.365,0.292 0.833,1.625 0.479,1.094 true 0.781,1.875 0.49,2.417 true 4.427,1.854 4.844,2.26 true 3.719,1.156 4.063,1.156 4.063,1.156 4.302,1.708 true 4.865,3.635 5.292,3.219 true 4.76,3.865 4.76,4.5 4.76,4.5 5.115,4.5 true 2.01,0.208 2.385,0.448 0.375,0.24 12 false *A 5.385,0.229 5.76,0.469 0.375,0.24 12 false *B 3.354,2.354 3.729,2.594 0.375,0.24 12 false *C 2.25,3.802 2.625,4.042 0.375,0.24 12 false *D 3.542,4.406 3.917,4.646 0.375,0.24 12 false *E 0.344,0.938 0.656,1.135 0.313,0.198 10 false *a 1.927,1.281 2.115,1.438 0.188,0.156 10 true *b 5.292,1.313 5.479,1.469 0.188,0.156 10 true *b 3,3.323 3.188,3.479 0.188,0.156 10 true *b 0.406,2.448 0.719,2.646 0.313,0.198 10 false *c 4.865,2.188 5.177,2.385 0.313,0.198 10 false *a 5.323,3.115 5.635,3.313 0.313,0.198 10 false *a 5.146,4.396 5.458,4.594 0.313,0.198 10 false *d 3.563,1.063 3.875,1.26 0.313,0.198 10 false *d
*A Colored Roller (Visible Type) *B Flat Cable (Visible Type), w/o Steering Heater
*C Flat Cable (Visible Type), w/ Steering Heater *D for Type A
*E for Type B - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45100 6.INSTALL STEERING WHEEL ASSEMBLY

Hide 45187 8.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 9.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 12. CHECK SRS WARNING LIGHT