Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) › 2014.08–2015.08
RM2660E _55 Steering _052826 STEERING COLUMN _0255458 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45203A 1.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.
C358214E01
0.708,1.604 0.885,0.427 0.885,0.427 1.188,0.427 false 0.802,1.573 1.052,0.438 false 1.26,0.333 1.573,0.531 0.313,0.198 10 false *a 2.667,1.135 2.844,1.323 0.177,0.188 10 false A

Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

Text in Illustration
*a Matchmark


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Be careful not to damage the dust cover.



Hide 45026D 2.INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C179100

Install the 4 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.


HINT:

Install the steering intermediate shaft assembly from the inside of the vehicle.



b.

Using needle nose pliers, lock the clamp to the steering column hole cover to install it.

NOTICE:

Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.



Hide 45220 3.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C172649E05
1.854,0.885 2.51,0.979 2.51,0.979 1.719,1.021 true 2.563,0.875 2.802,1.052 0.24,0.177 10 false *a

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering intermediate shaft assembly.

Text in Illustration
*a Matchmark

HINT:

Install the steering intermediate shaft from the inside of the vehicle.



b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45250 4.INSTALL STEERING COLUMN ASSEMBLY

a.

Align the matchmarks on the steering intermediate shaft and the steering column.


b.
C172648E03
1.906,1.208 2.417,0.99 2.417,0.99 1.917,0.75 true 2.469,0.906 2.729,1.125 0.26,0.219 10 false *a

Install the bolt.

Text in Illustration
*a Matchmark

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.

w/o Entry and Start System:

i.
C358201

Install the steering column with the 4 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



d.

w/ Entry and Start System

i.
C172654

Install the steering column with the 4 nuts.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)



Hide 6.INSTALL WIRE HARNESS PROTECTOR AND WIRE HARNESS

a.
C172656

Attach the 2 claws to connect the wire harness protector and wire harness.


Hide 73900 7.INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55303B 8.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55432D 10.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

Hide 55404C 14.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

Hide 55404C 15.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

Hide 55475A 16.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55474C 17.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55403C 19.INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

Hide 55449C 20.INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

Hide 21.INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.
U164929

Using pliers, grip the claws of the clamp and install the combination switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.


b.

Connect the connectors to the combination switch with spiral cable.


Hide 45286B 22.INSTALL UPPER STEERING COLUMN COVER

a.
C179482

Attach the claw to install the upper steering column cover.


b.

Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.


Hide 23.INSTALL LOWER STEERING COLUMN COVER

a.
C179481

Attach the 2 claws to install the lower steering column cover.


b.

Install the 3 screws.


Hide 45100 24.INSTALL STEERING WHEEL ASSEMBLY

Hide 45186 26.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 45187 27.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 28.CHECK FRONT WHEELS FACING STRAIGHT AHEAD

Hide 29.INSTALL FRONT WHEEL

Hide 30.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 31.INSPECT SRS WARNING LIGHT