Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM U

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash / Data List.


e.

Read the Data List according to the display on the GTS.

Pre-Crash
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status /
ON or OFF
ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status /
ON or OFF
ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-crash safety system on/off status /
ON or OFF
ON: Pre-crash safety system on
OFF: Pre-crash safety system off
-
Pre-Crash Safety Warning Buz Pre-crash safety warning buzzer
Valid or Inval
Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function
Valid or Inval
Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
Pre-Crash safety Warning Buz Pre-crash safety system warning buzzer /
Valid or Inval
Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Brake Pre-crash brake function /
Valid or Inval
Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
PBA Start Pre-crash brake assist activation signal /
OFF, Standby, Assist Lv1 or Assist Lv2
OFF: Pre-crash brake assist not operating Standby: Brake pedal not depressed during Pre-crash brake assist operation
Assist Lv1: Brake pedal depressed during Pre-crash brake assist operation
Assist Lv2: Brake pedal firmly depressed during Pre-crash brake assist operation
Signal status changes when the Pre-crash brake assist is activated before a collision (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake - - Not applicable to the vehicle
Brake Assist Standby Supplemental brake pressure signal /
ON or OFF
ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
-
Pre-Crash Brake Control Pre-crash brake operational status /
ON or OFF
ON: Pre-crash brake operating
OFF: Supplemental brake pressure not being provided
-
AVS Start - - Not applicable to the vehicle
VGRS Start - - Not applicable to the vehicle
PBA Control Pre-crash brake assist operational status /
Valid or Invalid
Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible
-
Pre-Crash Brake Ind Pre-crash system alarm warning message status /
ON or OFF
ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Crash Alarm Buzzer Pre-crash safety city buzzer status /
ON or OFF
ON: Pre-crash safety city buzzer sounding
OFF: Pre-crash safety city buzzer not sounding
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history /
ON or OFF
ON: History of low voltage
OFF: No history of low voltage
-
Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history /
ON or OFF
ON: History of vertical misalignment
OFF: No history of vertical misalignment
-
Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history /
ON or OFF
ON: History of horizontal misalignment
OFF: No history of horizontal misalignment
-
Front Recognition Camera-Malfunction History Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) /
ON or OFF
ON: History of malfunction
OFF: No history of malfunction
-
Control Mode ECU control mode status /
Normal or Check
Normal: Normal operation
Check: Operating in Control Mode
-
PCS Operation State Retention Setting Displays the setting of the PCS Operation State Retention Setting customize setting /
ON or OFF
ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 Displays the setting of the PCS Alarm Activation Distance Retention Setting 1 customize setting /
ON or OFF
ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 Displays the setting of the PCS Alarm Activation Distance Retention Setting 2 customize setting /
ON or OFF
ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 Displays the setting of the PCS Alarm Activation Distance Retention Setting 3 customize setting /
ON or OFF
ON: Customize setting set to ON
OFF: Customize setting set to OFF
-


f.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


g.

Read the Data List according to the display on the GTS.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch status/
ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Relay Output STPO terminal output condition/
ON or OFF
ON: Output
OFF: Not output
-



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Pre-Crash: Body Electrical / Pre-Crash 2 / Active Test.


ii.

for ABS/VSC/TRAC: Chassis / ABS/VSC/TRAC / Active Test.


iii.

for Combination Meter: Body Electrical / Combination Meter / Active Test.



e.

Perform Active Test according to the display on the GTS.

HINT:

The engine switch must be turned on (IG) to proceed with the Active Test using the GTS.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Pre-crash safety city buzzer assembly ON / OFF Test possible with engine switch on (IG), vehicle stopped

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop lights ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Precrash PCS OFF warning light ON / OFF -