Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM D

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  FREEZE FRAME DATA  


DESCRIPTION


a.

Whenever PCS DTC is detected, the driving support ECU assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data.



CHECK FREEZE FRAME DATA


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


e.

According to the GTS display, select a DTC that stored freeze frame data.


f.

Read the freeze frame data recorded when the DTC was stored.

Pre-Crash 2
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Turn Light RH Turn signal switch (right) status ON or OFF ON: Turn signal switch (right) on
OFF: Turn signal switch (right) off
-
Turn Light LH Turn signal switch (left) status ON or OFF ON: Turn signal switch (left) on
OFF: Turn signal switch (left) off
-
PCS OFF Switch Pre-crash safety system on/off status ON or OFF ON: Pre-crash safety system on
OFF: Pre-crash safety system off
-
PCS Indicator PCS malfunction warning message display request ON or OFF ON: Warning message displayed
OFF: Warning message not displayed
"Pre-Crash Safety System Dealer" is displayed
PCS Disabled Indicator PCS unavailable warning message display request ON or OFF ON: Warning message displayed
OFF: Warning message not displayed
"Pre-Crash Safety System
Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval Valid: Pre-crash safety system warning buzzer operation possible
Inval: Pre-crash safety system warning buzzer operation not possible
-
Pre-Crash Safety Brake Pre-crash brake function Valid or Inval Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2 OFF: Pre-crash brake assist not operating Standby: Brake pedal not depressed during pre-crash brake assist operation
Assist Lv1: Brake pedal depressed during pre-crash brake assist operation
Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation
Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
Warning Brake - - - Not applicable to the vehicle
Brake Assist Standby Supplemental brake pressure signal ON or OFF ON: Supplemental brake pressure being provided
OFF: Supplemental brake pressure not being provided
-
Pre-Crash Brake Control Pre-crash brake operational status ON or OFF ON: Pre-crash brake operating
OFF: Pre-crash brake not operating
-
AVS Start AVS control activation start ON or OFF ON: AVS control activated
OFF: AVS control not activated
-
VGRS Start - - - Not applicable to the vehicle
PBA Control Pre-crash brake assist operational status Valid or Invalid Valid: Pre-crash brake assist control operation possible
Invalid: Pre-crash brake assist control operation not possible
-
Pre-Crash Safety Brake Ind Pre-crash system alarm warning message status ON or OFF ON: Displayed
OFF: Not displayed
"BRAKE!" is displayed
PCS Crash Alarm Buzzer Pre-crash safety city buzzer ON or OFF ON: Pre-crash safety city buzzer sounding
OFF: Pre-crash safety city buzzer not sounding
-
Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF ON: History of low voltage
OFF: No history of low voltage
-
Front Radar- Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history ON or OFF ON: History of vertical misalignment
OFF: No history of vertical misalignment
-
Front Radar- Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history ON or OFF ON: History of horizontal misalignment
OFF: No history of horizontal misalignment
-
Front Recognition Camera-Malfunction History Forward recognition camera malfunction history (abnormal temperature, low voltage, DTC stored, etc.) ON or OFF ON: History of malfunction
OFF: No history of malfunction
-
Control Mode ECU control mode status Normal or Check Normal: Normal operation
Check: Operating in Control Mode
-
PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-
PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF ON: Customize setting set to ON
OFF: Customize setting set to OFF
-