Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.08
RM2660E _58 Vehicle Interior _052844 PRE-CRASH SAFETY _0255621 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

The driving support ECU assembly operates the pre-crash alarm control by sending a buzzer request signal to the pre-crash safety city buzzer.

If the driving support ECU assembly detects a malfunction in the pre-crash safety city buzzer circuit, it stores DTC C1A4A.

DTC No. DTC Detection Condition Trouble Area
C1A4A When the engine switch is on (IG) and the pre-crash alarm control is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the pre-crash safety city buzzer but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the pre-crash safety city buzzer but the buzzer sounds for 1 second or more.


·

Pre-crash safety city buzzer

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

B403796E82
0.156,0.677 1.979,1.094 1.823,0.417 10 false from IG1 NO.4 Relay 1.99,0.865 3.073,1.313 1.083,0.448 10 false ECU-IG NO. 6 3.396,0.594 4.135,0.969 0.74,0.375 10 false 2 3.563,0.677 4.302,1.052 0.74,0.375 10 false IG1 4.24,0.688 4.979,1.063 0.74,0.375 10 false BZ 4.479,0.583 5.219,0.958 0.74,0.375 10 false 1 5.365,0.594 6.104,0.969 0.74,0.375 10 false 3 5.125,2.115 7.094,2.375 1.969,0.26 10 false Driving Support ECU Assembly 5.531,0.698 6.271,1.073 0.74,0.375 10 false BZ 5.125,1.958 5.865,2.333 0.74,0.375 10 false E164 3.208,0.938 3.948,1.313 0.74,0.375 10 false E5 3.208,1.104 5.177,1.365 1.969,0.26 10 false Pre-crash Safety City Buzzer

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform the Active Test according to the display on the GTS.

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

This DTC can be stored by performing the Active Test.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Pre-crash safety city buzzer ON/OFF Test possible with engine switch on (IG), vehicle stopped


h.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A4A is output. A
DTC C1A4A is not output. B



A

2.CHECK TERMINAL VOLTAGE

B

2.CHECK TERMINAL VOLTAGE
a.
U164298E02
1.969,1.552 2.396,1.875 true 2.458,1.823 2.813,1.99 0.354,0.167 10 false IG1 0.542,1.135 0.875,1.323 0.333,0.188 10 false E5 0.125,0.104 0.313,0.292 0.188,0.188 10 false *a

Disconnect the pre-crash safety city buzzer connector.

Text in Illustration
*a Front view of wire harness connector
(to Pre-crash Safety City Buzzer)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Condition Specified Condition
E5-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
E5-2 (IG1) - Body ground Engine switch off Below 1 V



OK

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY CITY BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the pre-crash safety city buzzer connector.


b.

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
E5-1 (BZ) - E164-3 (BZ) Always Below 1 Ω
E5-1 (BZ) orE164-3 (BZ) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK B


A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR

B

6.INSPECT PRE-CRASH SAFETY CITY BUZZER (CONFIRM BUZZER OPERATION)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

5.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
5.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform "Active Test" according to the display on the GTS.

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

This DTC can be stored by performing the Active Test.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Pre-crash safety city buzzer ON/OFF Test possible with engine switch on (IG), vehicle stopped


h.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A4A is output. A
DTC C1A4A is not output. B



A

6.INSPECT PRE-CRASH SAFETY CITY BUZZER (CONFIRM BUZZER OPERATION)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PRE-CRASH SAFETY CITY BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the engine switch on (IG).


b.

Check if the pre-crash safety city buzzer is sounding.


Result
Result Proceed to
The pre-crash safety city buzzer does not sound when the engine switch is on (IG). A
The pre-crash safety city buzzer sounds continuously when the engine switch is on (IG). B


A

7.INSPECT PRE-CRASH SAFETY CITY BUZZER (UNIT INSPECTION)

B

8.REPLACE PRE-CRASH SAFETY CITY BUZZER
7.INSPECT PRE-CRASH SAFETY CITY BUZZER (UNIT INSPECTION)
a.

Remove the pre-crash safety city buzzer (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL).


b.

Result
Result Proceed to
Pre-crash safety city buzzer is abnormal. A
Pre-crash safety city buzzer is normal. B


A

8.REPLACE PRE-CRASH SAFETY CITY BUZZER

B

10.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
8.REPLACE PRE-CRASH SAFETY CITY BUZZER
a.

Replace the pre-crash safety city buzzer (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL).



NEXT

9.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
9.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform "Active Test" according to the display on the GTS.

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

This DTC can be stored by performing the Active Test.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Pre-crash Safety City Buzzer ON/OFF Test possible with engine switch on (IG), vehicle stopped


h.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A4A is output. A
DTC C1A4A is not output. B



A

REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK DTC OUTPUT (PRE-CRASH SAFETY SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



f.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


g.

Perform "Active Test" according to the display on the GTS.

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

This DTC can be stored by performing the Active Test.


Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Pre-crash Safety City Buzzer ON/OFF Test possible with engine switch on (IG), vehicle stopped


h.

Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A4A is output. A
DTC C1A4A is not output. B



A

REPLACE DRIVING SUPPORT ECU ASSEMBLY

B