Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255624 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 72462A 1.REMOVE VERTICAL ADJUSTER COVER LH (for 8 Way Seat Type)

B180752

a.

Using a screwdriver, detach the 2 claws and remove the vertical adjuster cover LH.

HINT:

Tape the screwdriver tip before use.



Hide 72495 2.REMOVE VERTICAL ADJUSTING HANDLE LH (for 8 Way Seat Type)

B180753

a.

Remove the 2 screws and vertical adjusting handle LH.


Hide 72457 3.REMOVE VERTICAL SEAT ADJUSTER KNOB (for 8 Way Seat Type)

B180754

a.

Remove the snap ring and vertical seat adjuster knob.


Hide 72526A 4.REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B180755E02
1.823,0.146 1.719,0.146 false 1.719,0.146 1.021,0.729 true 1.865,0.052 3.115,0.469 1.25,0.417 10 true Protective Tape

a.

Lift the reclining adjuster release handle LH.


b.

Using a screwdriver, detach the claw and remove the reclining adjuster release handle LH.

HINT:

Tape the screwdriver tip before use.



Hide 71812D 5.REMOVE FRONT SEAT CUSHION SHIELD LH

a.
B180757

w/ Seatback Board:

Disconnect the 2 rubber bands from the 2 hooks.


b.
B180756

w/o Seatback Board:

Disconnect the rubber band from the 2 hooks.


c.
B180758E03
2.646,0.354 2.833,0.521 0.188,0.167 10 true (1) 1.688,1.344 1.875,1.51 0.188,0.167 10 false (2) 0.781,1.615 0.969,1.781 0.188,0.167 10 false (3)

for 4 Way Seat Type:

i.

Remove the 2 screws.


ii.

Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.



d.
B180759E01
2.674,0.265 2.867,0.407 0.193,0.142 10 (1) 1.812,0.975 2.002,1.117 0.190,0.142 10 (2) 1.265,1.259 1.454,1.401 0.189,0.142 10 (3)

for 8 Way Seat Type:

i.

Remove the 3 screws.


ii.

Detach the 3 claws in the order shown in the illustration, and then remove the front seat cushion shield LH.



e.

w/ Lumbar Support:

Disconnect the lumbar switch connector.


Hide 84920 6.REMOVE LUMBAR SWITCH (w/ Lumbar support)

B449516

a.

Remove the 2 screws and lumbar switch.


Hide 73240 7.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Manual Seat)

Hide 73240 8.REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Bench Seat Type)

Hide 71862 9.REMOVE FRONT INNER SEAT CUSHION SHIELD LH

B180761

a.

Remove the screw.


b.

Detach the claw and clip, and then remove the front inner seat cushion shield LH.


Hide 10.REMOVE SEAT CUSHION COVER WITH PAD

a.
B180762

Using a clip remover, remove the 2 clips.


b.
B180763

w/ Lumbar Support:

Detach the wire harness clamp.


c.
B180765

w/ Occupant Detection Sensor:

Detach the 2 clamps and remove connector holder.


d.
B180764

Bend the 2 seat frame claws upward.


e.

Detach the hooks and remove the seat cushion cover with pad.


Hide 71072S 11.REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER

a.
B180709

Remove the hog rings and front separate type seat cushion cover from the front separate type seat cushion pad.


Hide 71706 12.REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH (w/ Seatback Board)

B180711

a.

Remove the 2 screws.


b.

Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.


Hide 71931 13.REMOVE FRONT SEAT HEADREST SUPPORT (w/ Active Headrest)

B180712

a.

Detach the 4 claws and remove the 2 front seat headrest supports.


Hide 14.REMOVE SEATBACK COVER WITH PAD

a.

w/ Seatback Board:

i.
B191295E01
2.94,0.187 3.291,0.332 0.352,0.145 10 Hook 3.003,1.432 3.355,1.576 0.352,0.145 10 Hook 0.039,1.499 0.391,1.644 0.352,0.145 10 Hook 2.702,2.863 3.307,3.035 0.605,0.172 10 Hog Ring 1.153,2.418 2.639,2.944 false 1.747,2.432 2.626,2.939 2.626,2.939 2.383,2.418 false 2.695,2.945 2.639,2.946 false 1.921,0.774 2.691,0.265 2.691,0.265 2.895,0.265 false 2.567,1.167 2.913,1.523 2.913,1.523 2.517,0.732 false 2.516,2.103 2.913,1.523 2.913,1.523 2.531,1.74 false 2.913,1.523 2.971,1.523 false 0.965,1.246 0.574,1.595 0.574,1.595 0.945,0.77 false 1.041,2.097 0.574,1.595 0.574,1.595 1.02,1.718 false 0.574,1.595 0.453,1.595 false

Remove the 3 hog rings and detach the 9 hooks.


ii.
B180716

w/ Front Seat Side Airbag:

Remove the nut and seatback cover bracket from the seat frame.



b.

w/o Seatback Board:

i.
B180766

Remove the 3 hog rings.


ii.
B180767

Open the 2 fasteners, and then open the front separate type seatback cover.


iii.
B180716

w/ Front Seat Side Airbag:

Remove the nut and seatback cover bracket from the seat frame.


iv.
B180768

Detach the 4 claws and remove the 2 front seat headrest supports.



c.

Remove the seatback cover with pad from the seatback frame.


Hide 71074S 15.REMOVE FRONT SEPARATE TYPE SEATBACK COVER

a.
B180717

w/ Front Seat Side Airbag:

Disconnect the seatback cover bracket from the front separate type seatback pad.


b.
B180718E03
1.177,1.031 1.323,1.031 1.323,1.031 1.542,1.167 true 0.156,0.927 1.146,1.406 0.99,0.479 10 true Fastening Tape

Remove the hog rings.


c.

Detach the fastening tape and remove the front separate type seatback cover from the front separate type seatback pad.


Hide 71876 16.REMOVE INSIDE RECLINING ADJUSTER COVER LH

B180770

a.

w/ Front Seat Side Airbag:

Detach the wire harness clamp.


b.

Remove the screw.


c.

Detach the claw and remove the inside reclining adjuster cover LH.


Hide 71875A 17.REMOVE INSIDE RECLINING ADJUSTER COVER RH

a.

w/ Lumbar Support:

Detach the wire harness clamp.


b.

Remove the screw.


c.

Detach the claw and remove the inside reclining adjuster cover RH.


Hide 71876G 18.REMOVE OUTSIDE RECLINING ADJUSTER COVER LH

B180769

a.

Remove the screw and outside reclining adjuster cover LH.


Hide 71875F 19.REMOVE OUTSIDE RECLINING ADJUSTER COVER RH

a.

Remove the screw and outside reclining adjuster cover RH.


Hide 72760D 20.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/Lumbar Support)

a.
B293541E02
2.219,1.573 1.833,1.573 1.833,1.573 1.833,1.219 true 2.25,1.469 3.281,1.906 1.031,0.438 10 true Cable Clamp

Remove the 4 springs.


b.

w/ Active Headrest:

Remove the cable clamp and disconnect the active headrest cable from the seatback spring.


c.

Detach the 4 hooks and remove the seatback spring.


d.
B180724

Disconnect the lumbar support adjuster connector.


e.

Remove the 2 screws and lumbar support adjuster assembly LH.


f.
B180725

Detach the 3 claws and remove the bush from the seat frame.


Hide 71644 21.REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest)

B180726

a.

Remove the 6 nuts, and then remove the lower active headrest unit together with the upper active headrest unit.


Hide 71643A 22.REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest)

B180727

a.

Remove the nut.


b.

Detach the cable clamp and remove the upper active headrest unit from the lower active headrest unit.


Hide 71874 23.REMOVE FRONT LOWER SEAT CUSHION SHIELD LH

B180771

a.

Detach the claw and remove the front lower seat cushion shield LH.


Hide 71873 24.REMOVE FRONT LOWER SEAT CUSHION SHIELD RH

a.

Detach the claw and remove the front lower seat cushion shield RH.


Hide 89178A 25.REMOVE SEAT POSITION SENSOR (w/ Front Seat Side Airbag)

Hide 73920A 26.REMOVE FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)

Hide 82192 27.REMOVE FRONT SEAT WIRE LH (w/ Wire Harness)

a.

Detach the wire harness clamps.


b.

Detach the claw and remove the front seat wire LH.


Hide 72140A 28.REMOVE FRONT INNER SEAT TRACK ASSEMBLY LH

a.

for 4 Way Seat Type:

i.
B185503

Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.


ii.
B180772

Using a T40 "TORX" socket wrench , remove the 4 "TORX" bolts and seat frame with adjuster.


iii.
B180773

Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and reinforcement.



b.

for 8 Way Seat Type:

i.
B180775

Detach the spring.


ii.

Using a T40 "TORX" socket wrench, remove the 2 "TORX" bolts and inner seat track bracket.


iii.

Using a T40 "TORX" socket, remove the "TORX" bolt and spring.


iv.
B180776

Using a T40 "TORX" socket, remove the 4 bolts and seat frame with adjuster.


v.
B180777

Using a T40 "TORX" socket wench, remove the 2 "TORX" bolts and reinforcement.



c.
B293537

Using a screwdriver, detach the spring and remove the front inner seat track assembly LH from the seat track adjusting handle as shown in the illustration.


Hide 72120 29.REMOVE FRONT OUTER SEAT TRACK ASSEMBLY LH

a.
B293539

Using a screwdriver, detach the spring and remove the front outer seat track assembly LH from the seat track adjusting handle as shown in the illustration.