Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  Power Seat Position is not Memorized  


DESCRIPTION

When the seat memory SET switch and a seat memory switch (seat memory switch 1, seat memory switch 2 or seat memory switch 3) are pressed simultaneously, the outer mirror control ECU commands the position control ECU and switch through CAN communication to record each position value.

WIRING DIAGRAM

B183720E02
0.052,2.63 2.130,2.792 2.078,0.161 10 Position Control ECU and Switch 1.008,0.731 1.433,0.884 0.425,0.153 10 MPX1 1.008,1.91 1.433,2.064 0.425,0.153 10 MPX2 0.052,2.466 0.312,2.620 0.260,0.153 10 c15 1.535,0.598 1.718,0.755 0.182,0.157 10 5 1.535,1.776 1.718,1.934 0.182,0.157 10 1 3.275,2.448 3.554,2.599 0.278,0.150 10 I18 3.316,0.601 3.429,0.741 0.113,0.139 10 1 3.283,1.778 3.472,1.923 0.189,0.145 10 21 3.543,0.73 3.967,0.884 0.425,0.153 10 CANH 3.543,1.917 3.967,2.071 0.425,0.153 10 CANL 4.674,0.423 4.866,0.584 0.193,0.161 10 8 4.674,0.822 4.866,0.983 0.193,0.161 10 7 4.674,1.217 4.866,1.377 0.193,0.161 10 6 4.674,1.62 4.866,1.781 0.193,0.161 10 9 4.634,2.008 4.827,2.169 0.193,0.161 10 10 4.342,0.514 4.553,0.664 0.211,0.150 10 M1 4.342,0.911 4.553,1.061 0.211,0.150 10 M2 4.342,1.305 4.553,1.456 0.211,0.150 10 M3 4.294,1.712 4.552,1.862 0.259,0.150 10 MM 4.089,2.1 4.550,2.265 0.461,0.165 10 MSWE 5.731,0.512 5.961,0.668 0.230,0.156 10 M1 5.731,0.903 5.961,1.059 0.230,0.156 10 M2 5.731,1.303 5.961,1.459 0.230,0.156 10 M3 5.731,2.098 5.841,2.254 0.110,0.156 10 E 5.731,1.709 6.180,1.862 0.450,0.153 10 MRY 5.534,1.202 5.644,1.358 0.110,0.156 10 2 5.534,0.806 5.644,0.962 0.110,0.156 10 3 5.534,0.414 5.644,0.570 0.110,0.156 10 4 5.534,1.605 5.644,1.761 0.110,0.156 10 5 5.534,1.999 5.644,2.155 0.110,0.156 10 6 3.275,2.642 4.899,2.808 1.624,0.165 10 Outer Mirror Control ECU 5.608,2.515 5.808,2.664 0.199,0.149 10 X1 5.608,2.673 6.910,2.849 1.302,0.177 10 Seat Memory Switch 0.85,3.399 1.607,3.554 0.757,0.155 10 : CAN Line 0.145,2.922 0.919,3.089 0.774,0.167 10 *1: for LHD 0.145,3.142 0.919,3.310 0.774,0.167 10 *2: for RHD 0.292,2.464 0.490,2.648 0.198,0.184 10 *1 0.552,2.466 0.812,2.620 0.260,0.153 10 c27 0.792,2.464 0.990,2.648 0.198,0.184 10 *2 3.481,2.448 3.678,2.632 0.197,0.184 10 *1 3.74,2.45 4.000,2.604 0.260,0.153 10 I24 3.956,2.448 4.154,2.632 0.198,0.184 10 *2 5.782,2.512 5.980,2.696 0.198,0.184 10 *1 6.042,2.514 6.262,2.668 0.221,0.153 10 X2 6.234,2.512 6.432,2.696 0.198,0.184 10 *2

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL FUNCTION
a.

Check that each function of the power seat operates normally by using the front power seat switches.

OK:

Each function of power seat operates normally by using seat switches.




OK

2.CHECK SEAT MEMORY SWITCH FUNCTION

NG

2.CHECK SEAT MEMORY SWITCH FUNCTION
a.

Perform a memory operation properly. Check that the buzzer sounds to indicate the completion of the memory operation.

NOTICE:
·

The seat position will not be recorded if the seat memory SET switch and 2 or more of the seat memory switches (for example, seat memory switch 1 and seat memory switch 2) are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat memory switch function operates normally.




OK

END

NG

3.CHECK COMBINATION METER FUNCTION
3.CHECK COMBINATION METER FUNCTION
a.

When the engine switch is on (IG) and the shift lever is in P, check that the combination meter shows that the shift lever is in P.

OK:

Meter shows that shift lever is in P.




OK

4.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)

NG

4.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
a.

Check the Data List for proper functioning of the seat memory switch.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SET Switch Seat memory SET switch signal / ON or OFF ON: Seat memory SET switch on
OFF: Seat memory SET switch off
-
M1 Switch Seat memory switch 1 signal / ON or OFF ON: Seat memory switch 1 on
OFF: Seat memory switch 1 off
-
M2 Switch Seat memory switch 2 signal / ON or OFF ON: Seat memory switch 2 on
OFF: Seat memory switch 2 off
-
M3 Switch Seat memory switch 3 signal / ON or OFF ON: Seat memory switch 3 on
OFF: Seat memory switch 3 off
-


OK:

On intelligent tester screen, each item changes between ON and OFF according to above chart.



OK

REPLACE POSITION CONTROL ECU AND SWITCH

NG

5.INSPECT SEAT MEMORY SWITCH
5.INSPECT SEAT MEMORY SWITCH
B179859E01
0.11,0.149 2.593,0.555 2.483,0.406 10 Component without harness connected: (Seat Memory Switch) 1.639,2.959 1.878,3.143 0.239,0.184 10 M1 0.774,2.959 0.953,3.143 0.179,0.184 10 E 2.025,2.823 2.264,3.006 0.239,0.184 10 M2 2.485,2.949 2.724,3.133 0.239,0.184 10 M3 1.146,2.823 1.497,3.006 0.350,0.184 10 MRY 2.267,2.268 2.602,2.94 false 2.052,2.272 2.165,2.815 false 1.836,2.268 1.781,2.944 false 1.619,2.273 1.349,2.809 false 1.406,2.274 0.843,2.949 false

a.

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (M1) - 6 (E) Seat memory switch 1 pressed Below 1 Ω
3 (M2) - 6 (E) Seat memory switch 2 pressed Below 1 Ω
2 (M3) - 6 (E) Seat memory switch 3 pressed Below 1 Ω
5 (MRY) - 6 (E) Seat memory SET switch pressed Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - SEAT MEMORY SWITCH)
B449437E01
0.979,2.01 1.313,1.708 true 1.385,2.063 1.552,1.698 true 1.979,2.031 1.875,1.708 true 2.396,2.042 2.135,1.708 true 2.75,1.854 2.375,1.688 true 1.115,4.271 1.208,3.833 true 1.469,4.229 1.417,3.833 true 1.781,4.313 1.635,3.833 true 2.094,4.177 1.875,3.854 true 2.542,4.323 2.115,3.865 true 0.24,0 2.5,0.375 2.26,0.375 10 false Front view of wire harness connector: (to Outer Mirror Control ECU) 0.292,1.125 0.635,1.354 0.344,0.229 10 false I18 0.281,1.51 0.625,1.74 0.344,0.229 10 false I24 0.635,1.052 0.979,1.281 0.344,0.229 10 false *1 0.635,1.396 0.979,1.625 0.344,0.229 10 false *2 0.74,1.948 1.083,2.177 0.344,0.229 10 false M3 1.281,2.063 1.625,2.292 0.344,0.229 10 false M2 1.938,2.073 2.281,2.302 0.344,0.229 10 false M1 2.344,2.031 2.688,2.26 0.344,0.229 10 false MM 2.781,1.833 3.375,2.104 0.594,0.271 10 false MSWE 0.229,2.344 2.49,2.719 2.26,0.375 10 false Front view of wire harness connector: (to Seat Memory Switch) 0.281,3.302 0.625,3.531 0.344,0.229 10 false X1 0.281,3.708 0.625,3.938 0.344,0.229 10 false X2 0.052,4.094 0.75,4.375 0.698,0.281 10 false *1: for LHD 0.042,4.385 0.74,4.667 0.698,0.281 10 false *2: for RHD 1.01,4.302 1.708,4.583 0.698,0.281 10 false M3 1.406,4.25 2.104,4.531 0.698,0.281 10 false M2 1.771,4.344 2.469,4.625 0.698,0.281 10 false M1 2.021,4.198 2.719,4.479 0.698,0.281 10 false MRY 2.573,4.302 3.271,4.583 0.698,0.281 10 false E

a.

Disconnect the I18*1 or I24*2 ECU connector.


b.

Disconnect the X1*1 or X2*2 switch connector.

HINT:

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I18-8 (M1) - X1-4 (M1) Always Below 1 Ω
I18-7 (M2) - X1-3 (M2) Always Below 1 Ω
I18-6 (M3) - X1-2 (M3) Always Below 1 Ω
I18-9 (MM) - X1-5 (MRY) Always Below 1 Ω
I18-10 (MSWE) - X1-6 (E) Always Below 1 Ω
I18-8 (M1) - Body ground Always 10 kΩ or higher
I18-7 (M2) - Body ground Always 10 kΩ or higher
I18-6 (M3) - Body ground Always 10 kΩ or higher
I18-9 (MM) - Body ground Always 10 kΩ or higher
I18-10 (MSWE) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I24-8 (M1) - X2-4 (M1) Always Below 1 Ω
I24-7 (M2) - X2-3 (M2) Always Below 1 Ω
I24-6 (M3) - X2-2 (M3) Always Below 1 Ω
I24-9 (MM) - X2-5 (MRY) Always Below 1 Ω
I24-10 (MSWE) - X2-6 (E) Always Below 1 Ω
I24-8 (M1) - Body ground Always 10 kΩ or higher
I24-7 (M2) - Body ground Always 10 kΩ or higher
I24-6 (M3) - Body ground Always 10 kΩ or higher
I24-9 (MM) - Body ground Always 10 kΩ or higher
I24-10 (MSWE) - Body ground Always 10 kΩ or higher




OK

7.CHECK OUTER MIRROR CONTROL ECU (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OUTER MIRROR CONTROL ECU (OPERATION)
a.

After replacing the outer mirror control ECU, check that the front power seat control functions operate normally using the front seat switches and seat memory switch.

OK:

Front power seat control functions operate normally.




OK

END (REPLACE OUTER MIRROR CONTROL ECU)

NG

REPLACE POSITION CONTROL ECU AND SWITCH