Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Seat Position Memory System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052845 SEAT _0255625 FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Seat Position Memory System)  One or more Power Seat Motors do not Operate  


DESCRIPTION

When the front power seat switch is operated, a command signal is sent to the position control ECU. The position control ECU then controls the appropriate seat motor as needed. The position control ECU is designed so that a malfunction of the seat memory system will not interfere with manual seat control.

WIRING DIAGRAM

B183730E01
0.561,1.721 1.631,1.945 1.070,0.223 10 Reclining Motor 5.582,8.076 6.937,8.447 1.355,0.370 10 Position Control ECU and Switch 4.507,6.197 5.570,6.571 1.063,0.373 10 Lumbar Support Switch 0.561,2.834 1.405,3.057 0.844,0.223 10 Slide Motor 0.561,3.955 1.384,4.146 0.822,0.191 10 Lifter Motor 0.561,5.037 1.876,5.278 1.314,0.241 10 Front Vertical Motor 5.703,0.89 6.320,1.093 0.617,0.203 10 RCL - 5.703,1.309 6.320,1.512 0.617,0.203 10 RCL + 5.703,2.417 6.320,2.620 0.617,0.203 10 SLD + 5.703,1.978 6.320,2.181 0.617,0.203 10 SLD - 5.703,3.561 6.320,3.763 0.617,0.203 10 LFT + 5.703,3.118 6.320,3.321 0.617,0.203 10 LFT - 5.703,4.662 6.320,4.865 0.617,0.203 10 FRV+ 5.703,4.227 6.320,4.430 0.617,0.203 10 FRV - 0.941,1.167 1.080,1.369 0.139,0.202 10 1 1.462,1.167 1.601,1.369 0.139,0.203 10 2 1.462,2.135 1.601,2.337 0.139,0.202 10 1 0.941,2.135 1.080,2.338 0.139,0.203 10 2 5.441,2.315 5.580,2.518 0.139,0.203 10 2 3.83,5.407 3.969,5.610 0.139,0.203 10 3 3.83,5.631 3.969,5.834 0.139,0.203 10 B 5.395,0.758 5.612,0.961 0.217,0.203 10 10 5.441,1.208 5.636,1.410 0.195,0.202 10 8 5.441,1.874 5.647,2.077 0.206,0.203 10 3 5.441,3.022 5.658,3.225 0.217,0.203 10 9 5.441,3.446 5.647,3.649 0.206,0.203 10 7 5.441,4.096 5.636,4.298 0.195,0.202 10 4 5.441,4.545 5.647,4.748 0.206,0.203 10 6 1.262,5.289 2.408,5.549 1.146,0.260 10 from Battery 0.505,7.087 2.142,7.304 1.636,0.217 10 Lumbar Support Adjuster 5.441,5.194 5.614,5.397 0.173,0.203 10 5 2.639,6.443 2.812,6.646 0.173,0.203 10 4 2.845,6.443 3.017,6.646 0.173,0.203 10 H 2.845,5.798 3.017,6.001 0.173,0.203 10 R 2.639,5.801 2.812,6.004 0.173,0.203 10 1 5.703,5.295 5.998,5.498 0.295,0.203 10 +B 5.703,7.315 6.153,7.523 0.450,0.208 10 GND 5.441,7.214 5.636,7.417 0.195,0.203 10 1 3.827,7.074 4.021,7.276 0.195,0.203 10 5 4.096,7.074 4.291,7.276 0.195,0.203 10 2 5.582,7.889 5.876,8.048 0.295,0.159 10 c14 4.507,6.011 4.808,6.191 0.302,0.180 10 c16 0.505,6.906 0.782,7.071 0.276,0.165 10 c21 0.561,4.865 0.835,5.034 0.274,0.170 10 c19 0.561,3.774 0.835,3.944 0.274,0.170 10 c18 0.561,2.653 0.835,2.823 0.274,0.170 10 c17 0.561,1.54 0.835,1.710 0.274,0.170 10 c20 0.155,8.241 0.922,8.425 0.767,0.184 10 *1: for LHD 0.155,8.466 0.922,8.649 0.767,0.184 10 *2: for RHD 5.82,7.889 6.011,8.060 0.191,0.171 10 *1 6.037,7.889 6.332,8.048 0.295,0.159 10 c26 6.275,7.889 6.466,8.060 0.191,0.171 10 *2 4.744,6.011 4.935,6.182 0.191,0.171 10 *1 4.961,6.011 5.256,6.170 0.295,0.159 10 c28 5.2,6.011 5.390,6.182 0.191,0.171 10 *2 0.799,1.54 0.989,1.711 0.191,0.171 10 *1 1.016,1.54 1.213,1.700 0.198,0.159 10 c6 1.175,1.54 1.365,1.711 0.191,0.171 10 *2 0.799,2.653 0.989,2.824 0.191,0.171 10 *1 1.016,2.653 1.213,2.813 0.198,0.159 10 c3 1.175,2.653 1.365,2.824 0.191,0.171 10 *2 0.799,3.774 0.989,3.945 0.191,0.171 10 *1 1.016,3.774 1.213,3.933 0.198,0.159 10 c4 1.175,3.774 1.365,3.945 0.191,0.171 10 *2 0.799,4.865 0.989,5.036 0.191,0.171 10 *1 1.016,4.865 1.213,5.024 0.198,0.159 10 c5 1.175,4.865 1.365,5.036 0.191,0.171 10 *2 0.735,6.905 0.926,7.076 0.191,0.171 10 *1 0.952,6.905 1.202,7.064 0.250,0.159 10 c29 1.19,6.905 1.381,7.076 0.191,0.171 10 *2 1.04,2.159 1.231,2.330 0.191,0.171 10 *1 1.541,2.159 1.732,2.330 0.191,0.171 10 *1 1.462,2.272 1.601,2.474 0.139,0.202 10 2 0.941,2.272 1.080,2.475 0.139,0.203 10 1 1.04,2.295 1.231,2.466 0.191,0.171 10 *2 1.541,2.295 1.732,2.466 0.191,0.171 10 *2 1.462,4.358 1.601,4.560 0.139,0.202 10 1 0.941,4.358 1.080,4.561 0.139,0.203 10 2 1.04,4.381 1.231,4.552 0.191,0.171 10 *1 1.541,4.381 1.732,4.552 0.191,0.171 10 *1 1.462,4.495 1.601,4.697 0.139,0.202 10 2 0.941,4.495 1.080,4.697 0.139,0.203 10 1 1.04,4.518 1.231,4.689 0.191,0.171 10 *2 1.541,4.518 1.732,4.689 0.191,0.171 10 *2 1.462,6.25 1.601,6.452 0.139,0.202 10 1 0.941,6.25 1.080,6.453 0.139,0.203 10 2 1.04,6.273 1.231,6.444 0.191,0.171 10 *1 1.541,6.273 1.732,6.444 0.191,0.171 10 *1 1.462,6.387 1.601,6.588 0.139,0.202 10 2 0.941,6.387 1.080,6.589 0.139,0.203 10 1 1.04,6.41 1.231,6.581 0.191,0.171 10 *2 1.541,6.41 1.732,6.581 0.191,0.171 10 *2 1.462,3.245 1.601,3.447 0.139,0.202 10 2 0.941,3.245 1.080,3.448 0.139,0.203 10 1 1.04,3.268 1.231,3.439 0.191,0.171 10 *1 1.541,3.268 1.732,3.439 0.191,0.171 10 *1 1.462,3.381 1.601,3.583 0.139,0.202 10 1 0.941,3.381 1.080,3.584 0.139,0.203 10 2 1.04,3.405 1.231,3.576 0.191,0.171 10 *2 1.541,3.405 1.732,3.576 0.191,0.171 10 *2 4.079,6.825 4.310,7.027 0.231,0.202 10 E 4.079,6.645 4.310,6.847 0.231,0.202 10 E2 4.272,6.671 4.462,6.842 0.191,0.171 10 *1 4.192,6.851 4.383,7.022 0.191,0.171 10 *2 3.782,6.825 4.012,7.027 0.231,0.202 10 E 3.694,6.645 3.925,6.847 0.231,0.202 10 E2 3.871,6.671 4.061,6.842 0.191,0.171 10 *1 3.879,6.851 4.069,7.022 0.191,0.171 10 *2

PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switches.

Result
Result Proceed to
All front power seat switch operations are malfunctioning except lumbar support switch operation A
Only lumbar support switch operation is malfunctioning B



A

2.READ VALUE USING INTELLIGENT TESTER (FRONT POWER SEAT SWITCH)

B

6.INSPECT LUMBAR SUPPORT SWITCH
2.READ VALUE USING INTELLIGENT TESTER (FRONT POWER SEAT SWITCH)
a.

Using the intelligent tester, read the Data List.

Driver Seat
Item Measurement Item/Display (Range) Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) / ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) / ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) / ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) / ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) / ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) / ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Sliding switch signal (Rearward) / ON or OFF ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
-
Slide Front Sliding switch signal (Forward) / ON or OFF ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
-

OK:

On intelligent tester screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT POWER SEAT MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT POWER SEAT MOTOR)
a.

Using the intelligent tester, perform the Active Test.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Reclining Seat reclining operation Front / OFF / Rear -
Front Vertical Operation Seat front vertical operation Up / OFF / Down -
Lifter Operation Seat lifter operation Up / OFF / Down -
Seat Slide Operation Seat sliding operation Front / OFF / Rear -

OK:

The power seat motors operate normally.




OK

REPLACE POSITION CONTROL ECU AND SWITCH

NG

4.INSPECT FRONT SEAT ASSEMBLY (FRONT POWER SEAT MOTOR)
4.INSPECT FRONT SEAT ASSEMBLY (FRONT POWER SEAT MOTOR)
a.

Remove the front seat assembly LH (for LHD) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).


b.

Remove the front seat assembly RH (for RHD) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).


c.
B188327E01
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Slide Motor)

Check operation of the slide motor.

i.

Check if the seat moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Forward
Battery positive (+) → 2
Battery negative (-) → 1
Rearward

for RHD
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Forward
Battery positive (+) → 1
Battery negative (-) → 2
Rearward




d.
B188327E03
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Front Vertical Motor)

Check operation of the front vertical motor.

i.

Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Upward
Battery positive (+) → 2
Battery negative (-) → 1
Downward

for RHD
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Upward
Battery positive (+) → 1
Battery negative (-) → 2
Downward




e.
B188327E04
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Lifter Motor)

Check operation of the lifter motor.

i.

Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Upward
Battery positive (+) → 1
Battery negative (-) → 2
Downward

for RHD
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Upward
Battery positive (+) → 2
Battery negative (-) → 1
Downward




f.
B188327E05
0.13,0.054 2.666,0.460 2.536,0.406 10 Component without harness connected: (Reclining Motor)

Check operation of the reclining motor.

i.

Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Forward
Battery positive (+) → 1
Battery negative (-) → 2
Rearward




Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH - POWER SEAT MOTOR)

B

C

REPLACE FRONT SEAT ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH - POWER SEAT MOTOR)
B449435E01
1.615,1.719 1.188,1.24 true 1.406,1.813 1.063,1.813 true 1.635,2.125 1.385,2.458 true 1.865,2.167 1.729,2.49 true 2.104,2.167 2.25,2.51 true 2.365,2.146 2.708,2.406 true 2.927,2.052 2.583,2.052 true 2.927,1.802 2.583,1.802 true 2.823,1.292 2.344,1.698 true 0.823,0.042 3.167,0.479 2.344,0.438 10 false Front view of wire harness connector: (to Position Control ECU and Switch) 1.615,1.021 2.042,1.292 0.427,0.271 10 false c14 2.115,1.021 2.542,1.292 0.427,0.271 10 false c26 1.833,0.938 2.26,1.208 0.427,0.271 10 false *1 2.385,0.938 2.813,1.208 0.427,0.271 10 false *2 0.792,1.125 1.26,1.333 0.469,0.208 10 false SLD+ 0.74,1.74 1.208,1.948 0.469,0.208 10 false GND 1.104,2.458 1.573,2.667 0.469,0.208 10 false FRV+ 1.573,2.51 2.042,2.719 0.469,0.208 10 false LFT+ 2.146,2.531 2.615,2.74 0.469,0.208 10 false RCL+ 2.729,2.406 3.198,2.615 0.469,0.208 10 false LFT 2.969,1.99 3.438,2.198 0.469,0.208 10 false RCL 2.948,1.729 3.417,1.938 0.469,0.208 10 false FRV 2.854,1.135 3.323,1.344 0.469,0.208 10 false SLD- 4.146,0.052 6.49,0.49 2.344,0.438 10 false Front view of wire harness connector: (to Power Seat Motor) 4.344,1.271 4.75,1.479 0.406,0.208 10 false c17 4.354,1.531 4.76,1.74 0.406,0.208 10 false c18 4.354,1.781 4.76,1.99 0.406,0.208 10 false c19 4.354,2.021 4.76,2.229 0.406,0.208 10 false c20 6.042,1.271 6.448,1.479 0.406,0.208 10 false c3 6.052,1.521 6.458,1.729 0.406,0.208 10 false c4 6.052,1.781 6.458,1.99 0.406,0.208 10 false c5 6.063,2.031 6.469,2.24 0.406,0.208 10 false c6 4.615,1.198 5.021,1.406 0.406,0.208 10 false *1 4.615,1.458 5.021,1.667 0.406,0.208 10 false *1 4.615,1.698 5.021,1.906 0.406,0.208 10 false *1 4.615,1.948 5.021,2.156 0.406,0.208 10 false *1 6.292,1.208 6.698,1.417 0.406,0.208 10 false *2 6.302,1.458 6.708,1.667 0.406,0.208 10 false *2 6.302,1.698 6.708,1.906 0.406,0.208 10 false *2 6.302,1.948 6.708,2.156 0.406,0.208 10 false *2 0.052,2.156 0.781,2.344 0.729,0.188 10 false *1: for LHD 0.052,2.417 0.781,2.604 0.729,0.188 10 false *2: for RHD

a.

Disconnect the c14*1 or c26*2 switch connector.


b.

Disconnect the c17*1, c18*1, c19*1, c20*1 or c3*2, c4*2, c5*2, c6*2 motor connectors.

HINT:

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
c14-3 (SLD-) - c17-2 Always Below 1 Ω
c14-2 (SLD+) - c17-1 Always Below 1 Ω
c14-4 (FRV-) - c19-2 Always Below 1 Ω
c14-6 (FRV+) - c19-1 Always Below 1 Ω
c14-9 (LFT-) - c18-1 Always Below 1 Ω
c14-7 (LFT+) - c18-2 Always Below 1 Ω
c14-10 (RCL-) - c20-1 Always Below 1 Ω
c14-8 (RCL+) - c20-2 Always Below 1 Ω
c14-1 (GND) - Body ground Always Below 1 Ω
c14-3 (SLD-) or c17-2 - Body ground Always 10 kΩ or higher
c14-2 (SLD+) or c17-1 - Body ground Always 10 kΩ or higher
c14-4 (FRV-) or c19-2 - Body ground Always 10 kΩ or higher
c14-6 (FRV+) or c19-1 - Body ground Always 10 kΩ or higher
c14-9 (LFT-) or c18-1 - Body ground Always 10 kΩ or higher
c14-7 (LFT+) or c18-2 - Body ground Always 10 kΩ or higher
c14-10 (RCL-) or c20-1 - Body ground Always 10 kΩ or higher
c14-8 (RCL+) or c20-2 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
c26-3 (SLD-) - c3-1 Always Below 1 Ω
c26-2 (SLD+) - c3-2 Always Below 1 Ω
c26-4 (FRV-) - c5-1 Always Below 1 Ω
c26-6 (FRV+) - c5-2 Always Below 1 Ω
c26-9 (LFT-) - c4-2 Always Below 1 Ω
c26-7 (LFT+) - c4-1 Always Below 1 Ω
c26-10 (RCL-) - c6-1 Always Below 1 Ω
c26-8 (RCL+) - c6-2 Always Below 1 Ω
c26-1 (GND) - Body ground Always Below 1 Ω
c26-3 (SLD-) or c3-1 - Body ground Always 10 kΩ or higher
c26-2 (SLD+) or c3-2 - Body ground Always 10 kΩ or higher
c26-4 (FRV-) or c5-1 - Body ground Always 10 kΩ or higher
c26-6 (FRV+) or c5-2 - Body ground Always 10 kΩ or higher
c26-9 (LFT-) or c4-2 - Body ground Always 10 kΩ or higher
c26-7 (LFT+) or c4-1 - Body ground Always 10 kΩ or higher
c26-10 (RCL-) or c6-1 - Body ground Always 10 kΩ or higher
c26-8 (RCL+) or c6-2 - Body ground Always 10 kΩ or higher




OK

REPLACE POSITION CONTROL ECU AND SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT LUMBAR SUPPORT SWITCH
B449436E01
1.083,1.708 0.885,1.167 true 0.792,2.281 0.594,1.74 true 2.552,1.75 2.333,1.271 true 2.844,1.74 3.031,1.271 true 2.302,2.104 2.427,1.813 true 2.719,2.146 2.719,1.823 true 3.135,2.135 3.031,1.833 true 2.948,3.823 2.75,3.281 true 2.635,4.323 2.448,3.844 true 0.271,4.198 0.521,3.896 true 0.542,4.313 0.688,3.885 true 0.813,4.323 0.813,3.927 true 1.146,4.302 0.979,3.917 true 1.396,4.219 1.115,3.885 true 0.052,0.01 0.729,0.208 0.677,0.198 12 false for LHD: 0.083,0.219 2.854,0.76 2.771,0.542 10 false Component without harness connected: (Lumbar Support Switch) 0.365,1.083 0.927,1.281 0.563,0.198 10 false Release 0.833,2.219 1.396,2.417 0.563,0.198 10 false Hold 2.25,1.104 2.813,1.302 0.563,0.198 10 false H 2.969,1.115 3.417,1.292 0.448,0.177 10 false E2 2.177,2.135 2.625,2.313 0.448,0.177 10 false E2 2.667,2.167 2.823,2.375 0.156,0.208 10 false B 3.135,2.146 3.292,2.354 0.156,0.208 10 false R 0.063,2.51 0.74,2.708 0.677,0.198 12 false for RHD: 0.104,2.708 2.875,3.25 2.771,0.542 10 false Component without harness connected: (Lumbar Support Switch) 2.427,3.208 2.99,3.406 0.563,0.198 10 false Hold 2.708,4.26 3.271,4.458 0.563,0.198 10 false Release 0.125,4.177 0.573,4.354 0.448,0.177 10 false E 0.458,4.323 0.906,4.5 0.448,0.177 10 false H 0.771,4.344 1.219,4.521 0.448,0.177 10 false B 1.177,4.302 1.625,4.49 0.448,0.188 10 false E 1.406,4.219 1.854,4.406 0.448,0.188 10 false R

a.

Remove the lumbar support switch (See page Vehicle Interior>SEAT>LUMBAR SWITCH (for Power Seat)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E2)
4 (H) - 5 (E2) Off
1 (R) - 2 (E2)
4 (H) - 5 (E2) Release
1 (R) - 3 (B)

for RHD
Tester Connection Switch Condition Specified Condition
3 (B) - 4 (H) Hold Below 1 Ω
1 (R) - 2 (E)
4 (H) - 5 (E) Off
1 (R) - 2 (E)
4 (H) - 5 (E) Release
1 (R) - 3 (B)




OK

7.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY

NG

REPLACE LUMBAR SUPPORT SWITCH

7.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY
B107944E09
0.771,2.344 1.365,1.49 true 1.896,0.969 2.698,1.167 0.802,0.198 10 false Clockwise 0.167,0.938 0.844,1.333 0.677,0.396 10 false Counter-clockwise 0.073,2.365 0.948,2.563 0.875,0.198 10 false Driving Axis 0.083,0 2.604,0.385 2.521,0.385 10 false Component without harness connected: (Lumbar Support Adjuster)


b.

Check operation of the lumbar support adjuster.

i.

Check that the lumbar support adjuster moves smoothly when the battery is connected to the lumbar support adjuster motor connector terminals.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Counterclockwise

for RHD
Measurement Condition Specified Condition
Battery positive (+) → 2
Battery negative (-) → 1
Clockwise
Battery positive (+) → 1
Battery negative (-) → 2
Counterclockwise





OK

8.CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT SWITCH - BATTERY AND BODY GROUND)

NG

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT SWITCH - BATTERY AND BODY GROUND)
U163948E01
0.079,0.058 2.466,0.459 2.387,0.401 10 Front view of wire harness connector: (to Lumbar Support Switch) 0.725,2.283 0.937,2.449 0.211,0.166 10 E2 0.725,2.463 0.877,2.629 0.152,0.166 10 E 1.791,2.516 1.933,2.682 0.142,0.166 10 B 2.148,2.11 2.564,2.407 false 1.485,2.113 1.137,2.428 false 1.707,2.123 1.833,2.502 false 0.263,1.7 0.623,1.893 0.360,0.193 10 c16 0.648,1.635 0.836,1.809 0.188,0.174 10 *1 0.263,2.061 0.623,2.254 0.360,0.193 10 c28 0.648,1.996 0.836,2.170 0.188,0.174 10 *2 0.94,2.282 1.128,2.456 0.188,0.174 10 *1 0.85,2.452 1.037,2.627 0.188,0.174 10 *2 2.602,2.244 2.813,2.410 0.211,0.166 10 E2 2.602,2.424 2.754,2.590 0.152,0.166 10 E 2.817,2.243 3.005,2.417 0.188,0.174 10 *1 2.726,2.414 2.914,2.588 0.188,0.174 10 *2 0.083,2.729 0.841,2.908 0.758,0.179 10 *1: for LHD 0.083,3.013 0.841,3.192 0.758,0.179 10 *2: for RHD

a.

Disconnect the c16*1 or c28*2 switch connector.

HINT:

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
c16-3 (B) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
c28-3 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
c16-5 (E2) - Body ground Always Below 1 Ω
c16-2 (E2) - Body ground

for RHD
Tester Connection Condition Specified Condition
c28-5 (E) - Body ground Always Below 1 Ω
c28-2 (E) - Body ground




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (LUMBAR SUPPORT SWITCH - LUMBAR SUPPORT ADJUSTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR