Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
82192
1.INSTALL FRONT SEAT WIRE LH
Attach the claw to install the front seat wire LH.
Attach the wire harness clamps and connect the connectors.
73920A
2.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH
89178A
3.INSTALL SEAT POSITION SENSOR (for Driver Side)
72403
4.INSTALL SEAT FRAME SET BRACKET SUB-ASSEMBLY (w/ Climate Control Seat System)
Attach the 4 hooks to install the seat frame set bracket sub-assembly.
88921D
5.INSTALL NO. 1 AIR FILTER (w/ Climate Control Seat System)
Rotate the No. 1 air filter clockwise to attach the claws and install it.
85863
6.INSTALL SEAT CLIMATE CONTROL BLOWER LH (w/ Climate Control Seat System)
Install the seat climate control blower LH with the nut.
Attach the wire harness clamp.
Install the 2 bolts and connect the connector.
85865A
7.INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seat Cushion)
Install the seat climate control controller LH with the 2 screws.
Attach the wire harness clamp.
Attach the 4 claws to connect the seat climate control blower LH.
85861
8.INSTALL SEAT CLIMATE CONTROL ECU (w/ Climate Control Seat System)
Attach the claw to install the seat climate control ECU.
Connect the connector.
87501D
9.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
Attach the claw to install the seat heater control sub-assembly.
Attach the wire harness clamp and connect the connector.
71874
10.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH
Attach the hook to install the front lower seat cushion shield LH.
Install the screw.
71873
11.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH
Attach the hook to install the front lower seat cushion shield RH.
Install the screw.
71643A
12.INSTALL UPPER ACTIVE HEADREST UNIT
Install the upper active headrest unit with the 4 nuts.
71644
13.INSTALL LOWER ACTIVE HEADREST UNIT
Install the lower active headrest unit with the 2 nuts.
Attach the clamp.
Connect the active headrest cable to the upper active headrest unit with the nut.
14.INSTALL BUSH (for Driver Side)
Attach the 3 claws to install the bush.
72760D
15.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Side)
Install the lumbar support adjuster LH with the 2 screws.
Connect the connector.
Attach the 4 hooks to install the seatback spring.
| *1 | Cable Clamp |
| *2 | Hook |
Install the 4 springs.
Connect the active headrest cable to the seatback spring with the cable clamp.
71876G
16.INSTALL OUTSIDE RECLINING ADJUSTER COVER LH
Attach the claw to install the outside reclining adjuster cover LH.
Install the screw.
71875F
17.INSTALL OUTSIDE RECLINING ADJUSTER COVER RH
Attach the claw to install the outside reclining adjuster cover RH.
Install the screw.
71876
18.INSTALL INSIDE RECLINING ADJUSTER COVER LH
Attach the claw to install the inside reclining adjuster cover LH.
Install the 2 screws.
Attach the wire harness clamp.
71875A
19.INSTALL INSIDE RECLINING ADJUSTER COVER RH
Attach the claw to install the inside reclining adjuster cover RH.
Install the 2 screws.
Attach the wire harness clamp.
20.INSTALL FRONT SEATBACK PROTECTOR
Apply double-sided tape as shown in the illustration.
| *1 | Double-sided tape |
Install the front seatback protector.
87510N
21.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
Set the front seatback heater assembly LH onto the front separate type seatback cover so that the name stamp is facing the front separate type seatback pad.
w/o Climate Control Seat System:
Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.
| *1 | Tack Pin | *2 | Front Separate Type Seatback Cover |
| *3 | Front Seatback Heater Assembly LH | *4 | Name Stamp |
w/ Climate Control Seat System:
Install the front seatback heater assembly LH to the front separate type seatback cover with new tack pins.
| *1 | Tack Pin | *2 | Front Separate Type Seatback Cover |
| *3 | Front Seatback Heater Assembly LH | *4 | Name Stamp |
71074S
22.INSTALL FRONT SEPARATE TYPE SEATBACK COVER
Attach the fastening tape to install the front separate type seatback cover.
| *1 | Hog Ring Pliers |
| *2 | Fastening Tape |
Using hog ring pliers, install new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Pass the seatback cover bracket through the hole of the front separate type seatback pad.
| *1 | Seatback Cover Bracket |
71074S
23.INSTALL FRONT SEPARATE TYPE SEATBACK COVER (w/ Climate Control Seat System)
Using hog ring pliers, install the front separate type seatback cover to the front separate type seatback pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Pass the seatback cover bracket through the hole of the front separate type seatback pad.
| *1 | Seatback Cover Bracket |
24.INSTALL SEATBACK COVER WITH PAD
Attach the hooks to install the seatback cover with pad.
| *1 | Hog Ring |
| *2 | Hog Ring Pliers |
Attach the seatback cover bracket with the nut.
| *1 | Seatback Cover Bracket |
After the seatback cover with pad is installed, make sure the seatback cover bracket is not twisted.
Using hog ring pliers, install new hog rings.
Be careful not to damage the cover.
71931
25.INSTALL FRONT SEAT HEADREST SUPPORT
Attach the 4 claws to install the 2 front seat headrest supports.
85865
26.INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System, for Seatback)
Attach the 4 hooks to install the seat climate control controller LH.
Attach the 2 claws to connect the seat climate control blower LH.
71706
27.INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH
Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
Install the 2 screws.
87510L
28.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
Set the front seat cushion heater assembly LH onto the front separate type seat cushion cover so that the name stamp is facing the front separate type seat cushion pad.
w/o Climate Control Seat System:
Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.
| *1 | Tack Pin | *2 | Front Separate Type Seat Cushion Cover |
| *3 | Front Seat Cushion Heater Assembly LH | *4 | Name Stamp |
w/ Climate Control Seat System:
Install the front seat cushion heater assembly LH to the front separate type seat cushion cover with new tack pins.
| *1 | Tack Pin | *2 | Front Separate Type Seat Cushion Cover |
| *3 | Front Seat Cushion Heater Assembly LH | *4 | Name Stamp |
71072S
29.INSTALL FRONT SEPARATE TYPE SEAT CUSHION COVER
Using hog ring pliers, install the front separate type seat cushion cover to the front separate type seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
30.INSTALL SEAT CUSHION COVER WITH PAD
Set the seat cushion cover with pad in place.
Attach the hooks to install the seat cushion cover with pad.
Bend the 2 seat frame claws downward.
for Front Passenger Side:
Attach the 2 clamps to connect the connector holder.
Connect the connector.
w/o Climate Control Seat System:
Connect the connector and attach the wire harness clamp.
Connect the connector and attach the 2 wire harness clamps.
w/ Climate Control Seat System:
Attach the wire harness clamp.
Connect the 2 connectors and attach the 4 wire harness clamps.
Install the 2 clips.
84922C
31.INSTALL FRONT POWER SEAT SWITCH LH
Install the front power seat switch LH with the 3 screws.
w/ Seat Position Memory System:
Connect the 2 connectors.
w/o Seat Position Memory System:
Connect the connector.
71862
32.INSTALL FRONT INNER SEAT CUSHION SHIELD LH
Attach the 2 claws and clip to install the front inner seat cushion shield LH.
Install the screw.
73240
33.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
84920
34.INSTALL LUMBAR SWITCH (for Driver Side)
Install the lumbar switch to the front seat cushion shield LH with the 2 screws.
71868A
35.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH
Attach the claw to install the front inner No. 1 cushion shield LH to the front seat cushion shield LH.
Install the screw.
71812D
36.INSTALL FRONT SEAT CUSHION SHIELD LH
for Driver Side:
Connect the connector.
Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.
Install the 3 screws.
Connect the 2 rubber bands.
Install the 2 screws.
84921A
37.INSTALL RECLINING POWER SEAT SWITCH KNOB
Attach the 2 claws to install the reclining power seat switch knob.
84921B
38.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Attach the 2 claws to install the slide and vertical power seat switch knob.