Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
72507D
1.INSTALL NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY
Install the release handle with the bolt.
72616A
2.INSTALL REAR SEATBACK LOCK STRIKER COVER LH
Attach the 2 clamps to install the cover.
72997C
3.INSTALL REAR NO. 2 SEATBACK COVER LH
Attach the 3 claws to install the cover.
72680A
4.INSTALL REAR SEATBACK LOCK STRIKER ASSEMBLY LH
Install the lock striker with the 2 nuts.
72695A
5.INSTALL REAR SEAT LOCK CONTROL CABLE
Attach the 2 clamps to install the lock control cable.
Attach the 2 cable clamps to connect the 2 cables.
71878A
6.INSTALL REAR INNER SEAT RECLINING COVER RH
Attach the claw to install the cover.
Install the screw.
71879A
7.INSTALL REAR INNER SEAT RECLINING COVER LH
Attach the claw to install the cover.
Install the screw.
79034
8.INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *1 | Hog Ring Pliers |
9.INSTALL SEATBACK COVER WITH PAD
Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog rings.
LH Side:
w/ Rear Center Seat Headrest:
Attach the 8 claws to install the 4 headrest supports.
Install the rear seat protector.
Insert the center headrest storage bag.
Attach the 2 hooks.
Close the fastener.
w/o Rear Center Seat Headrest:
Attach the 4 claws to install the 2 headrest supports.
Install the rear seat protector.
Attach the hook.
RH Side:
Attach the 4 claws to install the 2 headrest supports.
Install the rear seat protector.
Attach the hook.
71984A
10.INSTALL REAR SEAT HEADREST HANDLE
Install the snap ring to the headrest handle.
Install the headrest handle to the headrest.
71970
11.INSTALL REAR SEAT HEADREST ASSEMBLY (w/ Folding Headrest)
While releasing the lock inside the headrest support with a screwdriver, install the headrest.
Tape the screwdriver tip before use.
| *1 | Protective Tape |
71970
12.INSTALL REAR SEAT HEADREST ASSEMBLY (w/o Folding Headrest)
72779A
13.INSTALL REAR SEAT HINGE PAWL GUIDE
Install the guide with the screw.
72779
14.INSTALL REAR SEAT HINGE PAWL GUIDE
Attach the 5 claws to install the guide.
72668A
15.INSTALL REAR LOWER SEATBACK LOCK BEZEL
Attach the 3 claws and clip to install the seatback lock bezel.
79393
16.INSTALL REAR NO. 2 SEATBACK CUSHION
Install the seatback cushion with the screw.
78930
17.INSTALL NO. 3 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY
Attach the 2 clamps to install the 2 cables.
Attach the 2 cable clamps to connect the 2 cables.
79029A
18.INSTALL NO. 2 SEAT STAY SUB-ASSEMBLY
Install the seat stay with the bolt.
79032
19.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
w/o Bottle Holder:
Attach the fastening tape to install the seatback cover.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *1 | Hog Ring Pliers |
| *2 | Fastening Tape |
w/ Bottle Holder:
Attach the 3 fastening tapes to install the seatback cover.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *1 | Hog Ring Pliers |
| *2 | Fastening Tape |
79345A
20.INSTALL NO. 3 SEAT CUSHION PAD LH
21.INSTALL SEAT CUSHION COVER WITH PAD
66990B
22.INSTALL NO. 2 BOTTLE HOLDER
Install the No. 2 bottle holder with the 2 screws.
73949
23.INSTALL CAP
Attach the 4 claws to install the 2 caps.
71887C
24.INSTALL REAR SEAT CUSHION CARPET
Install the seat cushion carpet with new tack pins.
73580A
25.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY
73307
26.INSTALL REAR CENTER SEAT INNER BELT LH (w/ Rear Center Seat Headrest)
73302
27.INSTALL REAR CENTER SEAT INNER BELT RH (w/ Rear Center Seat Headrest)
72690C
28.INSTALL SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY LH
Attach the cable clamp to connect the cable.
Attach the claw to install the release lever.
Install the screw.
72345
29.INSTALL SEAT STAND FRAME CAP
Attach the 2 claws to install the stand frame cap.
72666B
30.INSTALL REAR SEAT LOCK COVER LH
Attach the 2 clamps to install the cover.
Install the 2 screws.
79367
31.INSTALL NO. 3 SEAT LEG COVER NO. 2
Attach the 4 claws to install the cover.
Install the 2 screws.
79382
32.INSTALL NO. 3 SEAT FRONT BRACKET COVER LH
Attach the 4 claws to install the cover.
72928
33.INSTALL REAR SEAT CUSHION UNDER COVER LH
Install the cover with the 7 screws.
Attach the 16 claws.
72918
34.INSTALL 3RD SEAT CUSHION LOCK COVER
Attach the 4 claws to install the 2 covers.
72906
35.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH
Install the seat link with the bolt and nut.
79246A
36.INSTALL NO. 2 SEAT LEG COVER NO. 2
Install the seat leg cover with the screw.
79384
37.INSTALL REAR NO. 3 SEAT LEG COVER LH
Install the seat leg cover with the 2 screws.
Install the spring of the seat stay ball-joint.
Connect the seat stay to the seat frame.
79957
38.INSTALL REAR SEAT REAR BRACKET COVER REAR
Attach the 2 claws to install the cover.
71843C
39.INSTALL RECLINING ADJUSTER COVER RH
Attach the 5 claws in the order shown in the illustration to install the cover.
Install the screw.
71844B
40.INSTALL RECLINING ADJUSTER COVER LH
Attach the 3 claws in the order shown in the illustration to install the cover.
Install the screw.
72526C
41.INSTALL NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH
Install the release handle with the screw.
72329
42.INSTALL SEAT ADJUSTER BOLT COVER
Attach the 2 claws to install the cover.