Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1GR-FE)
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255681 COMPRESSOR(for 1GR-FE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor and magnetic clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnetic clutch before installation.

Standard:
GRJ200L-GNANKV, GNMNKV, GPANKV, GPMNKV:

(Oil capacity inside the new compressor and magnetic clutch: 140 + 15 cc (4.7 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)

Except GRJ200L-GNANKV, GNMNKV, GPANKV, GPMNKV:

(Oil capacity inside the new compressor and magnetic clutch: 135 + 15 cc (4.6 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed from the new compressor when replacing)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

If a new compressor and magnetic clutch is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed compressor and magnetic clutch is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 or equivalent for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

E154180E01
3.271,1.792 3.408,1.938 0.137,0.147 10 1 2.973,1.826 3.128,1.972 0.155,0.147 10 2 3.18,1.115 3.335,1.262 0.155,0.147 10 3

a.

Install the cooler compressor with the 3 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



b.

Connect the connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E154179E02
2.604,0.448 2.75,0.635 0.146,0.188 10 false A 1.667,1.823 1.813,2.01 0.146,0.188 10 false B

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose.


d.

Connect the suction hose to the cooler compressor with the 2 bolts.

Torque:
for bolt A : 9.8 N*m (100 kgf*cm, 87 ft.*lbf)
for bolt B : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

E154178

a.

Remove the attached vinyl tape from the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the cooler refrigerant discharge hose.


d.

Connect the cooler refrigerant discharge hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 53737B 6.INSTALL FRONT FENDER APRON SEAL LH

E156500

a.

Install the seal with the 4 clips.


Hide 53292A 10.INSTALL UPPER RADIATOR SUPPORT SEAL