Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Rear Heater)


U165789E02
3.875,0.271 4.177,0.448 0.302,0.177 10 false E36 1.792,0.26 2.042,0.438 0.25,0.177 10 false z53 5.458,0.271 5.74,0.448 0.281,0.177 10 false E35

a.

Disconnect the E36 and E35 air conditioning amplifier assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E36-6 (+B1) - E36-1 (GND) R - W-B Battery power supply Always 11 to 14 V
E36-7 (+B2) - E36-1 (GND) R - W-B Battery power supply Always 11 to 14 V
E36-5 (IG+) - E36-1 (GND) G - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
E36-2 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω
E36-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
E35-6 (E2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the E36 and E35 air conditioning amplifier assembly connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z53-3 (B BUS) - z53-1 (BUS G) - Power supply for BUS IC (for front) Always 11 to 14 V
z53-10 (B BUS) - z53-8 (BUS G) - Power supply for BUS IC (for front) Always 11 to 14 V
E36-14 (RBBU) - E36-12 (RBUG) L - BR Power supply for BUS IC (for rear) Always 11 to 14 V
E35-25 (TR3) - Body ground V - Body ground Power supply for driver side duct sensor Engine switch on (IG)
Driver side duct sensor temperature: 25°C (77°F)
4.8 to 5.2 kΩ
E35-26 (TR4) - Body ground W - Body ground Power supply for front passenger side duct sensor Engine switch on (IG)
Front passenger side duct sensor temperature: 25°C (77°F)
4.8 to 5.2 kΩ
E35-16 (SG-2) - Body ground G - Body ground Ground for pressure sensor Always Below 1 Ω
E35-29 (SG-5) - Body ground G - Body ground Ground for compressor signal Always Below 1 Ω
E35-32 (SG-1) - Body ground B - Body ground Ground for room temperature sensor (for front) Always Below 1 Ω
z53-6 (SGA) - Body ground - Ground for evaporator temperature sensor Always Below 1 Ω
z53-1 (BUS G) - Body ground - Ground for BUS IC (for front) Always Below 1 Ω
z53-8 (BUS G) - Body ground - Ground for BUS IC (for front) Always Below 1 Ω
E35-34 (SGND) - Body ground BR - Body ground Ground for driver side duct sensor Always Below 1 Ω
E35-12 (SG-9) - Body ground L - Body ground Ground for front passenger side duct sensor Always Below 1 Ω
E35-2 (SG-6) - Body ground G - Body ground Ground for room temperature sensor signal (for Rear LH and Rear RH) Always Below 1 Ω
E36-12 (RBUG) - Body ground BR - Body ground Ground for BUS IC (for rear) Always Below 1 Ω
E35-1 (SG) - Body ground P - Body ground Ground for evaporator temperature sensor signal (for Rear) Always Below 1 Ω
E36-25 (CFN+) - Body ground*1 R - Body ground Condenser fan operation signal Engine switch on (IG) 11 to 14 V
E36-33 (COOL) - Body ground W - Body ground Cool box operation signal Engine switch on (IG)
Cool box switch: On
11 to 14 V
E36-29 (AC1) - Body ground L - Body ground Compressor operation signal Engine switch on (IG)
Blower switch: Lo
A/C switch: Off
11 to 14 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On
Below 1 V
E36-22 (ACT) - Body ground G - Body ground Compressor operation signal Engine switch on (IG)
Blower switch: Lo
A/C switch: Off or on (magnet clutch off)
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On (magnet clutch on)
11 to 14 V
E35-28 (LOCK) - E35-29 (SG-5) L - G Air compressor lock sensor signal Engine idling
A/C switch: On (magnet clutch on)
Blower switch: Lo
Pulse generation
(see waveform 1)
E35-10 (TAM) - E35-16 (SG-2) V - G Ambient temperature sensor signal Engine switch on (IG)
Ambient temperature:
25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Ambient temperature:
50°C (122°F)
0.5 to 0.7 V
E35-27 (S5-1) - E35-16 (SG-2) LG - G Power supply for pressure sensor Engine switch on (IG) 4.5 to 5.5 V
E35-20 (PRE) - E35-16 (SG-2) R - G Air conditioning pressure sensor signal Refrigerant pressure:
Normal
1.0 to 4.8 V
Refrigerant pressure:
Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi])
Below 1 V
Refrigerant pressure:
Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi])
4.8 V or higher
E36-18 (MGC) - E36-1 (GND) R - W-B Compressor magnet clutch operation signal Engine idling
Blower switch: Lo
A/C switch: On (magnet clutch on permitted)
Below 1 V
E36-3 (BLW) - E36-1 (GND) R - W-B Blower motor control signal Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 2)
E35-9 (TR) - E35-32 (SG-1) W - B Room temperature sensor signal (for front) Engine switch on (IG)
Front side interior temperature: 25°C (77°F)
1.6 to 1.8 V
Room temperature sensor signal (for front) Engine switch on (IG)
Front side interior temperature: 50°C (122°F)
0.5 to 0.7 V
E35-7 (TSD) - Body ground LG - Body ground Driver side solar sensor signal Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E35-8 (TSP) - Body ground GR - Body ground Passenger side solar sensor signal Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
z53-7 (TEA) - z53-6 (SGA) - Evaporator temperature sensor signal Engine switch on (IG)
Evaporator temperature: 15°C (59°F)
1.4 to 1.8 V
z53-2 (BUS) - z53-1 (BUS G) - BUS IC control signal (for front) Engine switch on (IG) Pulse generation
z53-9 (BUS) - z53-8 (BUS G) - BUS IC control signal (for front) Engine switch on (IG) Pulse generation
E35-18 (TR) - E35-2 (SG-6) R - G Room temperature sensor signal (for Rear LH) Engine switch on (IG)
Vehicle interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Vehicle interior temperature: 50°C (122°F)
0.5 to 0.7 V
E35-19 (TR7) - E35-2 (SG-6) R - G Room temperature sensor signal (for Rear RH) Engine switch on (IG)
Vehicle interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Vehicle interior temperature: 50°C (122°F)
0.5 to 0.7 V
E36-13 (RBUS) - E36-12 (RBUG) R - BR BUS IC control signal (for rear) Engine switch on (IG) Pulse generation
E35-17 (TEC) - E35-1 (SG) W - P Evaporator temperature sensor signal (for Rear) Engine switch on (IG)
Evaporator temperature:
15°C (59°F)
1.4 to 1.8 V
E36-31 (ALT) - Body ground R - Body ground Generator signal Engine idling Pulse generation
E36-32 (SW1) - Body ground BR - Body ground Idle up operation signal Engine switch on (IG)
Idle up switch: Off
Below 1 V
Engine switch on (IG)
Idle up switch: On
11 to 14 V
E36-20 (LIN1) - E36-1 (GND) Y - W-B LIN communication signal
(for A/C switch)
Engine switch on (IG) Pulse generation
E36-21 (RLIN) - E36-1 (GND) L - W-B LIN communication signal
(for Rear A/C switch)
Engine switch on (IG) Pulse generation
E36-27 (PTC1) - Body ground*2 W - Body ground PTC1 heater relay operation signal Engine idling
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Blower switch: Off → Lo
Below 1 V → 11 to 14 V
E36-26 (PTC2) - Body ground*2 R - Body ground PTC2 heater relay operation signal
E36-35 (PTC3) - Body ground*2 R - Body ground PTC3 heater relay operation signal
E36-17 (BLWH) - E36-1 (GND) L - W-B Blower motor control signal (for rear) Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 3)
E36-19 (RMGV) - E36-1 (GND) B - W-B Rear cooling unit expansion valve signal Engine switch on (IG) 11 to 14 V

*1: w/ Condenser Fan

*2: w/ PTC Heater



e.
E157042E05
0.323,1.031 0.688,1.229 0.365,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal
Item Content
Terminal No. (Symbol) E35-28 (LOCK) - E35-29 (SG-5)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition Engine idling
Blower switch: Lo
A/C switch: On

HINT:

When the rear blower level is increased, the duty ratio changes accordingly.



f.
E103396E55
2.938,1.656 3.313,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 2.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) E36-3 (BLW) - E36-1 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Engine switch on (IG)
Blower switch: Lo

HINT:

When the blower level is increased, the duty ratio changes accordingly.



g.
E103396E55
2.938,1.656 3.313,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 3.

Rear Blower Motor Control Signal
Item Content
Terminal No. (Symbol) E36-17 (BLWH) - E36-1 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Engine switch on (IG)
Blower switch: Lo

HINT:

When the rear blower level is increased, the duty ratio changes accordingly.




CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (w/o Rear Heater)


U163889E02
4.094,0.073 4.365,0.25 0.271,0.177 10 false E81 6.167,0.083 6.438,0.26 0.271,0.177 10 false z54

a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E81-21 (+B1) - E81-14 (GND) R - W-B Battery power supply Always 11 to 14 V
E81-1 (IG+) - E81-14 (GND) G - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
E81-14 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the E81 air conditioning amplifier assembly connector.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
z54-4 (B BUS) - z54-2 (BUS G) - Power supply for BUS IC (for front) Always 11 to 14 V
E81-35 (SG-5) - Body ground G - Body ground Ground for compressor signal Always Below 1 Ω
E81-13 (SG-2) - Body ground G - Body ground Ground for pressure sensor Always Below 1 Ω
E81-34 (SG-1) - Body ground B - Body ground Ground for room temperature sensor (for front) Always Below 1 Ω
z54-2 (BUS G) - Body ground - Ground for BUS IC (for front) Always Below 1 Ω
z54-5 (SGA) - Body ground - Ground for evaporator temperature sensor Always Below 1 Ω
E81-8 (LOCK) - E81-35 (SG-5) L - G Air compressor lock sensor signal Engine idling
A/C switch: On (magnet clutch on)
Blower switch: Lo
Pulse generation
(see waveform 1)
E81-39 (CFN+) - Body ground*1 R - Body ground Condenser fan operation signal Engine switch on (IG)
A/C switch: Off
Below 1 V
Engine switch on (IG)
A/C switch: On
11 to 14 V
E81-15 (COOL) - Body ground W - Body ground Cool box operation signal Engine switch on (IG)
Cool box switch: Off
Below 1 V
Engine switch on (IG)
Cool box switch: On
11 to 14 V
E81-17 (AC1) - Body ground L - Body ground Compressor operation signal Engine switch on (IG)
Blower switch: Lo
A/C switch: Off
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On
11 to 14 V
E81-27 (ACT) - Body ground G - Body ground Compressor operation signal Engine switch on (IG)
Blower switch: Lo
A/C switch: Off or on (magnet clutch off)
Below 1 V
Engine switch on (IG)
Blower switch: Lo
A/C switch: On (magnet clutch on)
11 to 14 V
E81-5 (TAM) - E81-13 (SG-2) V - G Ambient temperature sensor signal Engine switch on (IG)
Ambient temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Ambient temperature: 50°C (122°F)
0.5 to 0.7 V
E81-30 (S5-1) - E81-13 (SG-2) LG - G Power supply for pressure sensor Engine switch on (IG) 4.5 to 5.5 V
E81-9 (PRE) - E81-13 (SG-2) R - G Air conditioning pressure sensor signal Refrigerant pressure: Normal 1.0 to 4.8 V
Refrigerant pressure: Abnormal (less than 0.392 MPa [4.0 kgf/cm2, 57 psi]) Below 1 V
Refrigerant pressure: Abnormal (less than 3.187 MPa [32.5 kgf/cm2, 463 psi]) 4.8 V or higher
E81-20 (MGC) - E81-14 (GND) R - W-B Compressor magnet clutch operation signal Engine idling
Blower switch: Lo
A/C switch: On (magnet clutch on permitted)
Below 1 V
E81-18 (RCRL) - E81-14 (GND) B - Body ground Rear cooler control relay operation signal Engine switch on (IG)
Rear blower switch: Off
Below 1 V
Engine switch on (IG)
Rear blower switch: Lo
11 to 14 V
E81-23 (BLW) - E81-14 (GND) R - W-B Blower motor control signal Engine switch on (IG)
Blower switch: Lo
Pulse generation
(see waveform 2)
E81-29 (TR) - E81-34 (SG-1) W - B Room temperature sensor signal (for front) Engine switch on (IG)
Front side interior temperature: 25°C (77°F)
1.6 to 1.8 V
Engine switch on (IG)
Front side interior temperature: 50°C (122°F)
0.5 to 0.7 V
E81-32 (TSP) - Body ground GR - Body ground Passenger side solar sensor signal Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E81-33 (TSD) - Body ground LG - Body ground Driver side solar sensor signal Engine switch on (IG)
Solar sensor subjected to electric light
0.8 to 4.3 V
E81-36 (SW1) - Body ground BR - Body ground Idle up operation signal Engine switch on (IG)
Idle up switch: Off
Below 1 V
Engine switch on (IG)
Idle up switch: On
11 to 14 V
z54-6 (TEA) - z54-5 (SGA) - Evaporator temperature sensor signal Engine switch on (IG)
Evaporate temperature: 15°C (59°F)
1.4 to 1.8 V
z54-3 (BUS) - z54-2 (BUS G) - BUS IC control signal (for front) Engine switch on (IG) Pulse generation
E81-37 (LIN1) - E81-14 (GND) Y - W-B LIN communication signal Engine switch on (IG) Pulse generation
E81-25 (ALT) - Body ground R - Body ground Generator signal Engine idling Pulse generation
E81-3 (PTC1) - Body ground*2 W - Body ground PTC1 heater relay operation signal Engine idling
Set temperature: MAX HOT
Engine coolant temperature: Below 65°C (149°F)
Ambient temperature: Below 10°C (50°F)
Below 1 V → 11 to 14 V
E81-22 (PTC2) - Body ground*2 R - Body ground PTC2 heater relay operation signal
E81-4 (PTC3) - Body ground*2 R - Body ground PTC3 heater relay operation signal
E81-24 (MGCA) - E81-14 (GND) Y - W-B Viscous with magnet clutch operation signal Engine idling
Idle up switch: On
Below 1 V

*1: w/ Condenser Fan

*2: w/ PTC Heater



e.
E157042E05
0.323,1.031 0.688,1.229 0.365,0.198 10 false GND

Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal
Item Content
Terminal No. (Symbol) E81-8 (LOCK) - E81-35 (SG-5)
Tool Setting 200 mV/DIV., 10 ms/DIV.
Condition Engine idling
Blower switch: Lo
A/C switch: On

HINT:

When the rear blower level is increased, the duty ratio changes accordingly.



f.
E103396E55
2.938,1.656 3.313,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 2.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) E81-23 (BLW) - E81-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Engine switch on (IG)
Blower switch: Lo

HINT:

When the blower level is increased, the duty ratio changes accordingly.




CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


U164044E04
3.469,0.25 3.792,0.427 0.323,0.177 10 false F10

a.

Disconnect the F10 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F10-7 (IG+) - F10-1 (GND) G - W-B Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
F10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the F10 air conditioning control assembly connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F10-12 (DTP+) - F10-1 (GND) R - W-B Temperature up switch signal Temperature up switch not pressed Below 1 V
Temperature up switch pressed Alternating between 3.5 V or higher and below 1 V
F10-10 (PTP+) - F10-1 (GND) L - W-B Temperature up switch signal Temperature up switch not pressed Below 1 V
Temperature up switch pressed Alternating between 3.5 V or higher and below 1 V
F10-9 (S5) - F10-1 (GND) B - W-B Signal ground Always Below 1 Ω
F10-11 (DTP-) - F10-1 (GND) G - W-B Temperature down switch signal Temperature down switch not pressed Below 1 V
Temperature down switch pressed Alternating between 3.5 V or higher and below 1 V
F10-3 (PTP-) - F10-1 (GND) W - W-B Temperature down switch signal Temperature down switch not pressed Below 1 V
Temperature down switch pressed Alternating between 3.5 V or higher and below 1 V
F10-2 (SG) - F10-1 (GND) GR - W-B Signal ground Always Below 1 Ω



CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY


U166060E02
3.5,0.406 3.792,0.573 0.292,0.167 10 false E55

a.

Disconnect the E55 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
E55-6 (IG) - E55-1 (E) G - W-B Ignition power supply Always 11 to 14 V
E55-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


U164692E06
2.896,1.073 2.802,1.073 2.802,1.073 2.385,1.333 false 5.51,0.698 5.427,0.698 5.427,0.698 5.01,0.958 false 2.875,1.646 2.802,1.646 2.802,1.646 2.396,1.802 false 2.917,2.656 2.823,2.656 2.823,2.656 2.406,2.406 false 2.896,2.24 2.823,2.24 2.823,2.24 2.417,2.146 false 2.24,2.802 2.469,2.969 0.229,0.167 10 false 2A 1.083,3.635 1.313,3.802 0.229,0.167 10 false 2A 1.958,2.063 2.167,2.229 0.208,0.167 10 false 2B 3.083,3.635 3.292,3.802 0.208,0.167 10 false 2B 1.969,1.188 2.177,1.354 0.208,0.167 10 false 2C 5.667,3.625 5.875,3.792 0.208,0.167 10 false 2C 5.115,1.615 5.323,1.781 0.208,0.167 10 false 2D 1.573,5.188 1.781,5.354 0.208,0.167 10 false 2D 4.396,5.188 4.604,5.354 0.208,0.167 10 false 2E 5.583,0.625 5.792,0.792 0.208,0.167 10 false 2E 2.979,1 3.198,1.167 0.219,0.167 10 false E1 6.031,7.01 6.25,7.177 0.219,0.167 10 false E1 2.958,1.583 3.177,1.75 0.219,0.167 10 false E2 3.552,7 3.771,7.167 0.219,0.167 10 false E2 2.979,2.177 3.198,2.344 0.219,0.167 10 false E3 1.083,7 1.302,7.167 0.219,0.167 10 false E3 2.99,2.583 3.208,2.75 0.219,0.167 10 false E4 6.104,5.083 6.323,5.25 0.219,0.167 10 false E4

a.

Disconnect the 2A, 2B, and 2D ECU connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2B-20 (BATB) - Body ground L - Body ground Battery power supply Always 11 to 14 V
2A-1 (ACC) - Body ground B - Body ground ACC power supply Engine switch on (ACC) 11 to 14 V
2A-1 (ACC) - Body ground B - Body ground ACC power supply Engine switch off Below 1 V
2D-62 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.




MULTI-DISPLAY ASSEMBLY (w/ Navigation System)


U166353E02
0.479,0.906 0.813,1.156 0.333,0.25 10 false F90

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F90-2 (TEC+) - Body ground R - Body ground Temperature up switch signal Temperature up switch not pressed Below 1 V
Temperature up switch pressed 3.5 V or higher
F90-3 (TES+) - Body ground L - Body ground Temperature up switch signal Temperature up switch not pressed Below 1 V
Temperature up switch pressed 3.5 V or higher
F90-6 (AGND) - Body ground B - Body ground Signal ground Always Below 1 Ω
F90-7 (TEC-) - Body ground G - Body ground Temperature down switch signal Temperature down switch not pressed Below 1 V
Temperature down switch pressed 3.5 V or higher
F90-8 (TES-) - Body ground W - Body ground Temperature down switch signal Temperature down switch not pressed Below 1 V
Temperature down switch pressed 3.5 V or higher
F90-9 (BGND) - Body ground GR - Body ground Signal ground Always Below 1 Ω



MULTI-MEDIA MODULE RECEIVER ASSEMBLY (w/ Navigation System) (See page Vehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>TERMINALS OF ECU)