The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.
The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch off.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1422/22 | An open or short in the compressor lock sensor circuit. | ·
Cooler compressor assembly (A/C lock sensor) ·
Compressor drive belt ·
Harness or connector between cooler compressor assembly and air conditioning amplifier assembly ·
Air conditioning amplifier assembly ·
CAN communication line |
Use the intelligent tester to check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output (for LHD) | B |
| CAN DTC is output (for RHD) | C |
A
B
C
w/ Rear Heater
Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Measure the waveform of the connector.
| Item | Contents |
|---|---|
| Terminal No. (Symbol) | E35-28 (LOCK) - E35-29 (SG-5) |
| Tool Setting | 200 mV/DIV., 10 ms/DIV. |
| Condition | Engine running
A/C switch on Blower switch LO |
w/o Rear Heater
Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).
Measure the waveform of the connector.
| Item | Contents |
|---|---|
| Terminal No. (Symbol) | E81-8 (LOCK) - E81-35 (SG-5) |
| Tool Setting | 200 mV/DIV., 10 ms/DIV. |
| Condition | Engine running
A/C switch on Blower switch LO |
OK
NG
Disconnect the C30 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C30-1 (SSR+) - C30-2 (SSR-) | 20°C (68°F) | 65 to 125 Ω |
OK
NG
w/ Rear Heater
Disconnect the E35 amplifier connector.
Disconnect the C30 compressor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E35-28 (LOCK) - C30-1 (SSR+) | Always | Below 1 Ω |
| E35-29 (SG-5) - C30-2 (SSR-) | Always | Below 1 Ω |
| E35-28 (LOCK) - Body ground | Always | 10 kΩ or higher |
| E35-29 (SG-5) - Body ground | Always | 10 kΩ or higher |
w/o Rear Heater
Disconnect the E81 amplifier connector.
Disconnect the C30 compressor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-8 (LOCK) - C30-1 (SSR+) | Always | Below 1 Ω |
| E81-35 (SG-5) - C30-2 (SSR-) | Always | Below 1 Ω |
| E81-8 (LOCK) - Body ground | Always | 10 kΩ or higher |
| E81-35 (SG-5) - Body ground | Always | 10 kΩ or higher |
OK
NG