Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

E349882E01
0.531,0.104 1.563,0.313 1.031,0.208 10 false Blower Level 0.823,1.448 1.135,1.646 0.313,0.198 10 false LO 0.854,0.521 1.167,0.719 0.313,0.198 10 false HI 0.854,1 1.167,1.198 0.313,0.198 10 false M 1.052,2.115 1.365,2.313 0.313,0.198 10 false 0 1.521,2.104 1.833,2.302 0.313,0.198 10 false Low 2.375,2.094 2.688,2.292 0.313,0.198 10 false High 1.583,2.396 2.615,2.604 1.031,0.208 10 false SI Duty (%) 4.115,0.656 5.219,0.865 1.104,0.208 10 false Duty Ratio (%) = 5.469,0.542 5.719,0.74 0.25,0.198 10 false T1 5.469,0.781 5.719,0.979 0.25,0.198 10 false T2 6.167,0.646 6.417,0.844 0.25,0.198 10 false 100 5.25,1.302 5.5,1.5 0.25,0.198 10 false T1 5.458,2.219 5.708,2.417 0.25,0.198 10 false T2 4.469,1.625 5.021,1.833 0.552,0.208 10 false OPEN 4.625,1.917 4.938,2.115 0.313,0.198 10 false LO

The blower motor is operated by signals from the air conditioning amplifier assembly. The blower motor speed signals are transmitted by changes in the duty ratio.

Duty Ratio:

The duty ratio is the ratio of the blower motor OPEN time (T1) to the total of the blower motor OPEN and LO time (T2).

The blower motor controller controls the blower motor speed.

WIRING DIAGRAM

E160307E03
0.058,0.009 1.307,0.221 1.249,0.211 12 w/ Rear Heater: 0.925,2.275 1.264,2.412 0.338,0.138 10 GND 1.047,1.679 1.265,1.817 0.218,0.138 10 +B 1.094,0.71 1.265,0.848 0.171,0.138 10 SI 1.364,2.186 1.592,2.377 0.228,0.191 10 1 1.364,1.588 1.592,1.779 0.228,0.191 10 3 1.364,0.615 1.592,0.807 0.228,0.191 10 2 0.169,2.819 0.515,2.963 0.345,0.144 10 A29 0.169,2.975 1.569,3.179 1.399,0.205 10 Front Blower Motor 2.844,1.675 3.759,1.840 0.914,0.164 10 from Battery 5.898,2.333 6.266,2.524 0.369,0.191 10 GND 5.898,0.707 6.266,0.898 0.369,0.191 10 BLW 5.676,2.231 5.834,2.389 0.158,0.158 10 1 5.676,0.585 5.834,0.743 0.158,0.158 10 3 5.508,2.752 5.839,2.923 0.332,0.171 10 E36 5.508,2.934 7.105,3.266 1.598,0.332 10 Air Conditioning Amplifier Assembly

E160307E04
0.058,0.009 1.374,0.221 1.316,0.211 12 w/o Rear Heater: 0.925,2.275 1.264,2.412 0.338,0.138 10 GND 1.047,1.679 1.265,1.817 0.218,0.138 10 +B 1.094,0.71 1.265,0.848 0.171,0.138 10 SI 1.364,2.186 1.592,2.377 0.228,0.191 10 1 1.364,1.588 1.592,1.779 0.228,0.191 10 3 1.364,0.615 1.592,0.807 0.228,0.191 10 2 0.169,2.819 0.515,2.963 0.345,0.144 10 A29 0.169,2.975 1.569,3.179 1.399,0.205 10 Front Blower Motor 2.844,1.675 3.759,1.840 0.914,0.164 10 from Battery 5.898,2.333 6.266,2.524 0.369,0.191 10 GND 5.898,0.707 6.266,0.898 0.369,0.191 10 BLW 5.676,2.231 5.834,2.389 0.158,0.158 10 1 5.597,0.585 5.833,0.743 0.236,0.158 10 23 5.508,2.752 5.839,2.923 0.332,0.171 10 E81 5.508,2.934 7.105,3.266 1.598,0.332 10 Air Conditioning Amplifier Assembly

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT BLOWER MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the front blower motor operates.

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Front blower motor Min.: 0, Max.: 31 -

Result
Result Proceed to
Front blower motor operates normally A
Front blower motor does not operate B
Front blower motor operates but does not change speed C



A

B

2.CHECK HARNESS AND CONNECTOR (FRONT BLOWER MOTOR - BODY GROUND)

C

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - FRONT BLOWER MOTOR)
2.CHECK HARNESS AND CONNECTOR (FRONT BLOWER MOTOR - BODY GROUND)
U165773E02
1.24,2.167 1.104,2.833 false 0.281,1.677 0.583,1.917 0.302,0.24 10 false A29 0.979,2.865 1.417,3.073 0.438,0.208 10 false GND 0.313,0.146 2.635,0.5 2.323,0.354 10 false Front view of wire harness connector: (to Front Blower Motor)

a.

Disconnect the A29 motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (FRONT BLOWER MOTOR - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT BLOWER MOTOR - BATTERY)
U165774E02
2.167,2.146 2.292,2.719 false 2.229,2.771 2.552,2.979 0.323,0.208 10 false +B 0.24,1.698 0.542,1.938 0.302,0.24 10 false A29 0.292,0.125 2.583,0.542 2.292,0.417 10 false Front view of wire harness connector: (to Front Blower Motor)

a.

Disconnect the A29 motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-3 (+B) - Body ground Always 11 to 14 V




OK

4.CHECK FRONT BLOWER MOTOR (SI VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT BLOWER MOTOR (SI VOLTAGE)
U165775E02
1.76,2 1.906,2.635 false 1.854,2.688 2.125,2.896 0.271,0.208 10 false SI 0.24,1.635 0.521,1.875 0.281,0.24 10 false A29 0.198,0.115 2.458,0.479 2.26,0.365 10 false Component with harness connected: (Front Blower Motor)

a.

Disconnect the E36*1 or E81*2 amplifier connector.


b.

Reconnect the A29 motor connector.


c.

Measure the voltage according to the value(s) in the table below.

HINT:

*1: for LHD

*2: for RHD


Standard Voltage:
Tester Connection Switch Condition Specified Condition
A29-2 (SI) - Body ground Engine switch on (IG) 4.5 to 5.5 V




OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - FRONT BLOWER MOTOR)

NG

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - FRONT BLOWER MOTOR)
a.
U165943E01
0.091,0.115 2.569,0.461 2.479,0.346 10 Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 1.532,1.379 1.823,1.554 0.291,0.175 10 E36 1.96,4.222 2.299,4.367 0.339,0.145 10 BLW 2.607,3.829 2.958,3.992 0.352,0.163 10 GND 2.256,3.053 2.75,3.791 false 1.78,3.087 2.14,4.19 false

w/ Rear Heater

i.

Disconnect the E36 amplifier connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-3 (BLW) - E36-1 (GND) Engine switch on (IG)
Blower switch off
4.5 to 5.5 V




b.
U166045E01
0.206,0.148 2.695,0.498 2.489,0.350 10 Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 1.77,1.757 2.141,1.954 0.371,0.198 10 E81 2.202,3.753 2.558,3.903 0.356,0.150 10 BLW 2.818,3.138 3.173,3.288 0.356,0.150 10 GND 2.546,3.035 2.805,3.193 false 2.395,3.135 2.396,3.737 false

w/o Rear Heater

i.

Disconnect the E81 amplifier connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-23 (BLW) - E81-1 (GND) Engine switch on (IG)
Blower switch off
4.5 to 5.5 V





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - FRONT BLOWER MOTOR)
a.
U165943E01
0.091,0.115 2.569,0.461 2.479,0.346 10 Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 1.532,1.379 1.823,1.554 0.291,0.175 10 E36 1.96,4.222 2.299,4.367 0.339,0.145 10 BLW 2.607,3.829 2.958,3.992 0.352,0.163 10 GND 2.256,3.053 2.75,3.791 false 1.78,3.087 2.14,4.19 false

w/ Rear Heater

i.

Disconnect the E36 amplifier connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E36-3 (BLW) - E36-1 (GND) Engine switch on (IG)
Blower switch off
4.5 to 5.5 V




b.
U166045E01
0.206,0.148 2.695,0.498 2.489,0.350 10 Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 1.77,1.757 2.141,1.954 0.371,0.198 10 E81 2.202,3.753 2.558,3.903 0.356,0.150 10 BLW 2.818,3.138 3.173,3.288 0.356,0.150 10 GND 2.546,3.035 2.805,3.193 false 2.395,3.135 2.396,3.737 false

w/o Rear Heater

i.

Disconnect the E81 amplifier connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-23 (BLW) - E81-1 (GND) Engine switch on (IG)
Blower switch off
4.5 to 5.5 V





OK

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)
a.

w/ Rear Heater

E349914E01
1.604,0.927 1.958,1.146 0.354,0.219 1.448,2.396 1.844,1.5 false 2.375,2.417 2.177,1.51 false 0.115,0.104 2.406,0.51 2.292,0.406 10 false Component with harness connected: (Air Conditioning Amplifier Assembly) 1.656,0.969 1.948,1.135 0.292,0.167 10 true E36 1.302,2.438 1.677,2.646 0.375,0.208 10 true BLW 2.24,2.448 2.615,2.656 0.375,0.208 10 true GND 6.104,0.896 6.698,1.104 0.594,0.208 10 true 1 V/DIV. 6.26,2 6.635,2.208 0.375,0.208 10 true GND 4.469,2.302 5.458,2.521 0.99,0.219 10 true 500 μsec./DIV.

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) E36-3 (BLW) - E36-1 (GND)
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Engine switch on (IG)
Blower switch: off → on

OK:

Waveform is as shown in the illustration.


HINT:

Waveform varies with the blower level.




b.

w/o Rear Heater

E349915E01
1.833,1.156 2.167,1.385 0.333,0.229 2.135,2.385 2.365,1.823 false 2.635,2.333 2.49,1.74 false 0.146,0.104 2.448,0.51 2.302,0.406 10 false Component with harness connected: (Air Conditioning Amplifier Assembly) 1.875,1.188 2.177,1.365 0.302,0.177 10 false E81 6.188,0.719 6.854,0.927 0.667,0.208 10 false 1 V/DIV. 1.969,2.438 2.333,2.656 0.365,0.219 10 false BLW 2.563,2.385 2.927,2.604 0.365,0.219 10 false GND 4.458,2.146 5.417,2.344 0.958,0.198 10 false 500 μsec./DIV. 6.333,1.823 6.698,2.042 0.365,0.219 10 false GND

i.

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


ii.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) E81-23 (BLW) - E81-1 (GND)
Tool Setting 1 V/DIV., 500 μsec./DIV.
Condition Engine switch on (IG)
Blower switch: OFF → ON

OK:

Waveform is as shown in the illustration.


HINT:

Waveform varies with the blower level.





OK

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY