Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower with fan motor sub-assembly is operated by signals from the air conditioning amplifier assembly. The rear blower with fan motor sub-assembly speed signals are transmitted by changes in the duty ratio.

The rear blower motor controller controls the rear blower with fan motor sub-assembly speed.

WIRING DIAGRAM

E330395E03
5.984,1.346 6.505,1.522 0.521,0.176 10 BLWH 5.69,1.27 5.931,1.447 0.242,0.176 10 17 5.765,1.908 6.007,2.084 0.242,0.176 10 1 4.001,0.63 4.243,0.807 0.242,0.176 10 1 4.036,0.864 5.034,1.040 0.998,0.176 10 A/C RR NO.1 5.143,0.713 6.141,0.889 0.998,0.176 10 from Battery 4.001,1.27 4.243,1.447 0.242,0.176 10 8 4.001,1.91 4.243,2.087 0.242,0.176 10 4 1.856,0.63 2.097,0.807 0.242,0.176 10 1 1.856,1.27 2.097,1.447 0.242,0.176 10 3 1.856,1.91 2.097,2.087 0.242,0.176 10 6 1.856,2.55 2.097,2.727 0.242,0.176 10 2 2.082,2.55 2.324,2.727 0.242,0.176 10 2 2.825,2.55 3.067,2.727 0.242,0.176 10 1 1.854,2.905 3.269,3.312 1.415,0.407 10 Rear Blower with Fan Motor Sub-assembly 1.772,3.634 3.365,4.078 1.593,0.445 10 Wiring Air Conditioning Harness Sub-assembly 0.1,3.441 1.483,3.674 1.382,0.233 10 z51 0.1,3.599 1.483,3.833 1.382,0.233 10 Blower Motor Control 5.509,2.409 6.891,2.643 1.382,0.233 10 E36 5.509,2.568 7.127,3.009 1.617,0.441 10 Air Conditioning Amplifier Assembly 5.984,1.993 6.505,2.214 0.521,0.222 10 GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR BLOWER MOTOR)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the rear blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Rear Blower Motor Rear blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Rear blower with fan motor sub-assembly is operated normally using the GTS.




OK

NG

2.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
2.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Remove the rear blower with fan motor sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>REMOVAL).


b.

Inspect the rear blower with fan motor sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E330396

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Wiring Air Conditioning Harness Sub-assembly)


OK

4.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Disconnect the E36 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 - E36-17 (BLWH) Always Below 1 Ω
8 or E36-17 (BLWH) - Body ground Always 10 kΩ or higher




OK

5.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY
a.

Replace the wiring air conditioning harness sub-assembly with a new or known good one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

END (WIRING AIR CONDITIONING HARNESS SUB-ASSEMBLY WAS DEFECTIVE)

NG

6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
6.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U166490E02
1.948,1.052 2.083,1.375 2.083,1.375 2.354,1.375 false 0.083,0.073 0.438,0.323 0.354,0.25 10 false *a 0.677,0.698 1.031,0.948 0.354,0.25 10 false z51 2.427,1.271 2.781,1.521 0.354,0.25 10 false SI 2.875,2.667 3.229,2.917 0.354,0.25 10 false GND

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) z51-3 (SI) - Body ground
Tool Setting 2 V/DIV., 500 μs/DIV.
Condition
·

Ignition switch ON

·

Blower switch LO



OK:

Waveform is as shown in the illustration.


HINT:

Waveform varies with the blower level.




OK

NG

7.CHECK BLOWER MOTOR CONTROL
7.CHECK BLOWER MOTOR CONTROL
a.

Replace the blower motor control with a new or known good one and check that the condition returns to normal.

OK:

Same problem does not occur.




OK

END (BLOWER MOTOR CONTROL WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY