Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Air Conditioning Control Panel Circuit  


DESCRIPTION

This circuit consists of the No. 2 air conditioning control assembly* and the air conditioning amplifier assembly. When the No. 2 air conditioning control assembly is operated, signals are transmitted to the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the No. 2 air conditioning control assembly is operated.

HINT:

*: w/ Rear Heater


WIRING DIAGRAM

E157369E11
5.564,0.845 5.997,1.026 0.433,0.181 10 RLIN 1.389,0.845 1.741,1.026 0.353,0.181 10 RLIN 1.562,1.364 1.733,1.545 0.171,0.181 10 IG 1.621,1.911 1.748,2.092 0.126,0.181 10 E 3.744,1.376 5.255,1.550 1.511,0.174 10 from IG1 NO. 3 Relay 2.435,1.515 3.438,1.696 1.003,0.181 10 ECU-IG NO. 2 5.405,2.648 7.124,3.092 1.718,0.444 10 Air Conditioning Amplifier Assembly 5.405,2.47 5.734,2.639 0.328,0.169 10 E36 0.674,2.604 2.057,2.930 1.383,0.326 10 No. 2 Air Conditioning Control Assembly 0.886,3.296 2.501,3.477 1.615,0.181 10 : LIN Communication Line 5.255,0.676 5.426,0.857 0.171,0.181 10 21 1.833,0.667 1.989,0.848 0.156,0.181 10 4 1.833,1.277 1.989,1.459 0.156,0.181 10 6 1.833,1.83 1.989,2.011 0.156,0.181 10 1 0.674,2.442 1.173,2.625 0.498,0.184 10 E55

PROCEDURE

1.INSPECT FUSE (ECU-IG NO. 2)
a.

Remove the ECU-IG NO. 2 fuse from the cowl side junction block LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG NO. 2 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING CONTROL - BODY GROUND AND BATTERY)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING CONTROL - BODY GROUND AND BATTERY)
U165785E01
0.112,0 2.610,0.539 2.498,0.539 10 Front view of wire harness connector: (to No. 2 Air Conditioning Control Assembly) 0.336,1.477 0.666,1.647 0.330,0.171 10 E55 0.522,2.036 0.734,2.192 0.212,0.157 10 E 2.673,2.036 2.899,2.200 0.226,0.164 10 IG 2.209,1.914 2.634,2.096 false 1.1,1.914 0.674,2.096 false

a.

Disconnect the E55 No. 2 air conditioning control assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E55-1 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Switch Condition Specified Condition
E55-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 2 AIR CONDITIONING CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - NO. 2 AIR CONDITIONING CONTROL)
E349929E01
0.521,1.635 0.865,1.896 0.344,0.26 5.25,1.229 5.563,1.448 0.313,0.219 1.813,2.229 2.115,2.969 false 5.781,2.813 5.979,3.25 false 0.177,0.156 2.729,0.583 2.552,0.427 10 false Front view of wire harness connector: (to No. 2 Air Conditioning Control Assembly) 4.094,0.167 6.604,0.583 2.51,0.417 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 0.583,1.677 0.896,1.875 0.313,0.198 10 false E55 1.99,3 2.375,3.219 0.385,0.219 10 false RLIN 5.854,3.292 6.24,3.51 0.385,0.219 10 false RLIN 5.292,1.26 5.583,1.438 0.292,0.177 10 true E36

a.

Disconnect the E55 No. 2 air conditioning control assembly connector.


b.

Disconnect the E36 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E36-21 (RLIN) - E55-4 (RLIN) Always Below 1 Ω
E55-4 (RLIN) - Body ground Always 10 kΩ or higher
E36-21 (RLIN) - Body ground




OK

4.CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (OPERATION)
a.

Replace the No. 2 air conditioning control assembly with a new or properly functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING PANEL>DISASSEMBLY).


b.

Operate the No. 2 air conditioning control assembly to check that it functions properly.

OK:

No. 2 air conditioning control assembly function operates normally.




OK

REPLACE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY