Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Air Conditioning Relay Circuit  


DESCRIPTION

When the No. 2 air conditioning control assembly (rear blower switch) is set to position LO or higher, the contact of the RR A/C relay is closed, current flows to the rear blower motor, and the rear blower motor operates. The rear blower motor speed can be changed by exchanging the ground and the rear blower resistor circuit with the No. 2 air conditioning control assembly (rear blower switch).

WIRING DIAGRAM

E162050E02
5.813,3.792 7.146,4.156 1.333,0.365 10 false Air Conditioning Amplifier Assembly 6.302,1.281 6.708,1.458 0.406,0.177 10 false RCRL 6.292,2.948 6.698,3.125 0.406,0.177 10 false GND 3.458,1.594 4.01,1.792 0.552,0.198 10 false RR A/C 1.427,5.135 2.823,5.438 1.396,0.302 10 false Rear Blower Resistor 5.458,4.781 6.729,5.021 1.271,0.24 10 false Rear Blower Motor 0.51,2.01 3,2.385 2.49,0.375 10 false No. 2 Air Conditioning Control Assembly (Rear Blower Switch) 2.625,1.448 3.135,1.625 0.51,0.177 10 false A/C IG 0.74,1.292 2.188,1.531 1.448,0.24 10 false from IG1 NO. 2 Relay 2.896,2.646 3.094,2.823 0.198,0.177 10 false LO 0.51,1.802 0.823,1.979 0.313,0.177 10 false E89 5.458,4.594 5.771,4.771 0.313,0.177 10 false z49 3.927,5.281 6.188,5.521 2.26,0.24 10 false Rear Cooling Unit Expansion Valve 0.365,3.698 1.24,4.438 0.875,0.74 10 false Wiring Air Conditioning Harness Sub-assembly 3.927,5.104 4.24,5.281 0.313,0.177 10 false z50 5.844,3.615 6.156,3.792 0.313,0.177 10 false E81 1.427,4.969 1.74,5.146 0.313,0.177 10 false z52 2.875,4.698 3.073,4.875 0.198,0.177 10 false LO 2.646,2.75 2.844,2.927 0.198,0.177 10 false HI 2.167,2.74 2.406,2.917 0.24,0.177 10 false M2 1.646,2.719 1.875,2.896 0.229,0.177 10 false M1 2.604,4.635 2.802,4.813 0.198,0.177 10 false HI 2.135,4.656 2.375,4.833 0.24,0.177 10 false M2 1.573,4.656 1.802,4.833 0.229,0.177 10 false M1 0.531,2.635 0.677,2.813 0.146,0.177 10 false E 5.979,1.208 6.146,1.385 0.167,0.177 10 false 18 5.979,2.875 6.146,3.052 0.167,0.177 10 false 14 4.99,4.281 5.146,4.458 0.156,0.177 10 false 1 3.896,4.281 4.052,4.458 0.156,0.177 10 false 1 4.073,1.208 4.229,1.385 0.156,0.177 10 false 2 1.708,4.281 1.865,4.458 0.156,0.177 10 false 2 2.26,4.271 2.417,4.448 0.156,0.177 10 false 3 4.063,0.74 4.219,0.917 0.156,0.177 10 false 3 2.813,4.281 2.969,4.458 0.156,0.177 10 false 1 1.708,2.99 1.865,3.167 0.156,0.177 10 false 3 2.26,2.99 2.417,3.167 0.156,0.177 10 false 4 3.271,0.813 3.427,0.99 0.156,0.177 10 false 5 2.802,2.969 2.958,3.146 0.156,0.177 10 false 8 3.177,2.552 3.333,2.729 0.156,0.177 10 false 5 0.313,2.542 0.469,2.719 0.156,0.177 10 false 6 3.177,4.729 3.333,4.906 0.156,0.177 10 false 4 3.458,0.385 3.615,0.563 0.156,0.177 10 false 4 5.354,4.292 5.51,4.469 0.156,0.177 10 false 2 4.406,4.292 4.563,4.469 0.156,0.177 10 false 2 3.271,1.198 3.427,1.375 0.156,0.177 10 false 1 1.292,0.906 2.146,1.135 0.854,0.229 10 false from Battery

PROCEDURE

1.INSPECT FUSE (A/C IG, RR A/C NO.2)
a.

Remove the A/C IG and RR A/C NO. 2 fuses from the cowl side junction block LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C IG fuse Always Below 1 Ω
RR A/C NO. 2 fuse Always Below 1 Ω




OK

2.INSPECT RR A/C RELAY

NG

REPLACE FUSE

2.INSPECT RR A/C RELAY
B106753E22
2.51,0.844 2.51,0.656 false 2.854,1.177 3.042,1.177 false 2.5,1.51 2.5,1.708 false 2.063,1.198 2.063,1.729 false 2.479,1.031 1.813,1.031 false 0.813,0.146 0.958,0.375 0.146,0.229 10 false 4 0.333,0.792 0.427,0.99 0.094,0.198 10 false 5 1.292,0.781 1.385,0.979 0.094,0.198 10 false 3 0.323,1.604 0.417,1.802 0.094,0.198 10 false 1 1.302,1.583 1.396,1.781 0.094,0.198 10 false 2 1.667,0.969 1.76,1.167 0.094,0.198 10 false 4 3.104,1.104 3.198,1.302 0.094,0.198 10 false 5 2.031,1.75 2.125,1.948 0.094,0.198 10 false 3 2.458,0.417 2.552,0.615 0.094,0.198 10 false 1 2.448,1.74 2.542,1.938 0.094,0.198 10 false 2

a.

Remove the RR A/C relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

3.INSPECT REAR BLOWER MOTOR

NG

REPLACE RR A/C RELAY

3.INSPECT REAR BLOWER MOTOR
U166006E01
1.782,1.094 2.517,0.467 false 2.516,0.287 2.859,0.468 0.343,0.181 10 1 (-) 1.656,1.094 0.968,0.388 false 0.587,0.247 0.942,0.429 0.355,0.181 10 2 (+) 1.595,0.132 1.887,0.297 0.292,0.166 10 z49

a.

Disconnect the z49 motor connector.


b.

Connect the battery's positive (+) lead to terminal 2 and the negative (-) lead to terminal 1, then check that the rear blower motor operates smoothly.

OK:

The rear blower motor operates smoothly.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
z49-1 (-) - z49-2 (+) Rear blower motor operates 1 to 3 A




OK

4.INSPECT NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (REAR BLOWER SWITCH)

NG

4.INSPECT NO. 2 AIR CONDITIONING CONTROL ASSEMBLY (REAR BLOWER SWITCH)
U166078E02
2.302,1.552 2.406,1.865 false 0.99,1.344 0.604,1.542 false 1.281,1.604 1.24,1.917 false 1.219,1.344 0.656,1.854 false 1.583,1.188 2.833,0.969 false 0.063,0.073 2.646,0.5 2.583,0.427 10 false Component without harness connected: (No. 2 Air Conditioning Control Assembly) 0.302,0.979 0.625,1.156 0.323,0.177 10 false E89 2.906,0.896 3.167,1.073 0.26,0.177 10 false M1 1.177,1.958 1.354,2.104 0.177,0.146 10 false HI 2.365,1.896 2.5,2.094 0.135,0.198 10 false E 0.354,1.479 0.573,1.656 0.219,0.177 10 false LO 0.448,1.854 0.719,2.042 0.271,0.188 10 false M2

a.

Remove the No. 2 air conditioning control assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING PANEL>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
ALL - E89-6 (E) OFF 10 kΩ or higher
E89-5 (LO) - E89-6 (E) LO Below 1 Ω
E89-3 (M1) - E89-6 (E) M1 Below 1 Ω
E89-4 (M2) - E89-6 (E) M2 Below 1 Ω
E89-8 (HI) - E89-6 (E) HI Below 1 Ω




OK

5.INSPECT REAR BLOWER RESISTOR

NG

REPLACE NO. 2 AIR CONDITIONING CONTROL ASSEMBLY

5.INSPECT REAR BLOWER RESISTOR
E158871E01
1.906,1.48 2.561,0.926 false 1.44,1.461 0.809,0.961 false 1.433,1.776 0.753,1.392 false 1.931,1.77 2.536,1.455 false 2.606,0.796 2.797,0.969 0.191,0.173 10 HI 2.611,1.37 2.892,1.541 0.281,0.171 10 M2 0.486,0.829 0.742,1.022 0.256,0.192 10 M1 0.424,1.281 0.658,1.472 0.233,0.191 10 LO 0.185,0.029 2.692,0.414 2.507,0.385 10 Component without harness connected: (Rear Blower Resistor)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z52-1 (HI) - z52-2 (M1) Always 1.32 to 1.52 Ω
z52-1 (HI) - z52-3 (M2) Always 0.39 to 0.45 Ω
z52-1 (HI) - z52-4 (LO) Always 2.24 to 2.4 Ω




OK

6.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)

NG

6.CHECK REAR COOLING UNIT EXPANSION VALVE (OPERATION)
a.

Replace the rear cooling unit expansion valve (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT (w/o Heater)>DISASSEMBLY).

HINT:

Since the rear cooling unit expansion valve cannot be inspected while it is removed from the vehicle, replace the rear cooling unit expansion valve with a normal one and check that the condition returns to normal.


OK:

Same problem does not occur.




OK

NG

7.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - WIRING AIR CONDITIONING HARNESS)
7.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - WIRING AIR CONDITIONING HARNESS)
E349940E01
4.49,1.604 4.833,1.854 0.344,0.25 1.073,2.167 1.448,1.854 false 1.542,2.229 1.646,1.865 false 2.188,2.25 2.083,1.865 false 2.5,2.177 2.26,1.844 false 5.438,1.635 5,1.385 false 5.438,1.948 5.052,2.177 false 6.146,1.406 5.76,1.635 false 6.125,2.188 5.76,1.917 false 0.271,0.104 2.573,0.656 2.302,0.552 10 false Front view of wire harness connector: (to Wiring Air Conditioning Harness Sub-assembly) 4.302,0.146 6.604,0.542 2.302,0.396 10 false Front view of wire harness connector: (to Rear Blower Resistor) 0.875,2.208 1.146,2.406 0.271,0.198 10 false LO 1.438,2.25 1.708,2.448 0.271,0.198 10 false M1 2.146,2.292 2.417,2.49 0.271,0.198 10 false M2 2.49,2.198 2.76,2.396 0.271,0.198 10 false HI 4.823,1.271 5.094,1.469 0.271,0.198 10 false HI 4.823,2.146 5.094,2.344 0.271,0.198 10 false M2 6.219,1.302 6.49,1.5 0.271,0.198 10 false M1 6.156,2.198 6.427,2.396 0.271,0.198 10 false LO 4.552,1.635 4.823,1.833 0.271,0.198 10 false Z52

a.

Disconnect the wiring air conditioning harness sub-assembly connector.


b.

Disconnect the z52 rear blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (M1) - z52-2 (M1) Always Below 1 Ω
5 (M2) - z52-3 (M2) Always Below 1 Ω
4 (HI) - z52-1 (HI) Always Below 1 Ω
7 (LO) - z52-4 (LO) Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (REAR BLOWER SWITCH - WIRING AIR CONDITIONING HARNESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (REAR BLOWER SWITCH - WIRING AIR CONDITIONING HARNESS)
E349942E01
0.521,1.646 0.854,1.885 0.333,0.24 1.052,2.281 1.396,1.938 false 2.302,1.927 2.604,2.271 false 2.302,1.667 2.771,1.938 false 2.458,1.646 2.823,1.688 false 2.104,1.563 2.625,1.156 false 4.573,2.135 4.938,1.979 false 5,2.313 5.146,1.99 false 5.688,2.344 5.479,2 false 6.146,2.177 5.708,1.969 false 0.417,0.104 2.708,0.656 2.292,0.552 10 false Front view of wire harness connector: (to No. 2 Air Conditioning Control Assembly) 4.198,0.104 6.49,0.656 2.292,0.552 10 false Front view of wire harness connector: (to Wiring Air Conditioning Harness Sub-assembly) 0.563,1.677 0.875,1.865 0.313,0.188 10 false E89 0.927,2.302 1.135,2.5 0.208,0.198 10 false E 2.615,2.302 2.823,2.5 0.208,0.198 10 false HI 2.802,1.938 3.01,2.135 0.208,0.198 10 false M2 2.875,1.615 3.083,1.813 0.208,0.198 10 false LO 2.667,1.052 2.875,1.25 0.208,0.198 10 false M1 4.406,2.094 4.615,2.292 0.208,0.198 10 false HI 4.917,2.333 5.125,2.531 0.208,0.198 10 false M2 5.635,2.344 5.844,2.542 0.208,0.198 10 false M1 6.188,2.125 6.396,2.323 0.208,0.198 10 false LO

a.

Disconnect the E89 No. 2 air conditioning control assembly connector.


b.

Disconnect the Wiring air conditioning harness sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E89-3 (M1) - 6 (M1) Always Below 1 Ω
E89-4 (M2) - 5 (M2) Always Below 1 Ω
E89-8 (HI) - 4 (HI) Always Below 1 Ω
E89-5 (LO) - 7 (LO) Always Below 1 Ω
E89-6 (E) - Body ground Always Below 1 Ω




OK

9.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - REAR BLOWER MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (REAR BLOWER RESISTOR - REAR BLOWER MOTOR)
U166007E02
1.479,1.646 0.813,1.99 false 0.625,1.969 0.823,2.167 0.198,0.198 10 false HI 0.635,1.219 0.938,1.406 0.302,0.188 10 false z52 0.469,3.74 0.771,3.927 0.302,0.188 10 false z49 0.24,0.125 2.573,0.552 2.333,0.427 10 false Front view of wire harness connector: (to Rear Blower Resistor) 0.24,2.521 2.542,2.938 2.302,0.417 10 false Front view of wire harness connector: (to Rear Blower Motor)

a.

Disconnect the z52 rear blower resistor connector.


b.

Disconnect the z49 rear motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z52-1 (HI) - z49-1 Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - BODY GROUND AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (REAR BLOWER MOTOR - BODY GROUND AND BATTERY)
U166008E02
0.521,1.292 0.823,1.479 0.302,0.188 10 false z49 0.302,0.125 2.656,0.698 2.354,0.573 10 false Front view of wire harness connector: (to Rear Blower Motor)

a.

Disconnect the z49 rear motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z49-2 - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z49-2 - Body ground Engine switch on (IG)
Heater control (blower switch) HI
11 to 14 V




OK

11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND)
U166010E02
1.74,2.167 2.208,2.917 false 1.469,2.167 1.208,2.927 false 2.156,2.958 2.563,3.135 0.406,0.177 10 false GND 0.948,2.969 1.354,3.146 0.406,0.177 10 false RCRL 1.688,1.042 1.979,1.208 0.292,0.167 10 false E81 0.167,0.094 2.646,0.438 2.479,0.344 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly)

a.

Disconnect the E81air conditioning amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E81-18 (RCRL) - Body ground Engine switch on (IG)
Heater control (blower switch): OFF
11 to 14 V
E81-18 (RCRL) - Body ground Engine switch on (IG)
Heater control (blower switch): ON
Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-14 (GND) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR