The temperature control switch assembly LH and RH sends the temperature up and down signal to the air conditioning amplifier assembly through the air conditioning control assembly.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B14B2 is not output..
OK
NG
Check that the temperature control switches operate.
| Result | Proceed to |
|---|---|
| Temperature control switch LH does not operate | A |
| Temperature control switch RH does not operate | B |
| Temperature control switch LH and RH do not operate | C |
A
B
C
Remove the temperature control switch assembly LH (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Entry and Start System)>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (UP) - 4 (SE) | UP switch pressed | Below 1 Ω |
| UP switch not pressed | 10 kΩ or higher | |
| 5 (DOWN) - 4 (SE) | DOWN switch pressed | Below 1 Ω |
| DOWN switch not pressed | 10 kΩ or higher |
| *a | Component without harness connected
(Temperature Control Switch Assembly LH) |
OK
NG
Disconnect the F133 temperature control switch assembly LH connector.
Disconnect the F10 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F133-3 (UP) - F10-12 (DTP+) | Always | Below 1 Ω |
| F133-5 (DOWN) - F10-11 (DTP-) | Always | Below 1 Ω |
| F133-4 (SE) - F10-9 (S5) | Always | Below 1 Ω |
| F133-3 (UP) - Body ground | Always | 10 kΩ or higher |
| F133-5 (DOWN) - Body ground | Always | 10 kΩ or higher |
| F133-4 (SE) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the temperature control switch assembly RH (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Entry and Start System)>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (UP) - 4 (SE) | UP switch pressed | Below 1 Ω |
| UP switch not pressed | 10 kΩ or higher | |
| 3 (DOWN) - 4 (SE) | DOWN switch pressed | Below 1 Ω |
| DOWN switch not pressed | 10 kΩ or higher |
| *a | Component without harness connected
(Temperature Control Switch Assembly LH) |
OK
NG
Disconnect the F132 temperature control switch assembly RH connector.
Disconnect the F10 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F132-5 (UP) - F10-10 (PTP+) | Always | Below 1 Ω |
| F132-3 (DOWN) - F10-3 (PTP-) | Always | Below 1 Ω |
| F132-4 (SE) - F10-2 (SG) | Always | Below 1 Ω |
| F132-5 (UP) - Body ground | Always | 10 kΩ or higher |
| F132-3 (DOWN) - Body ground | Always | 10 kΩ or higher |
| F132-4 (SE) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the air conditioning control assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (w/o Entry and Start System)>REMOVAL).
Check that the temperature control with temperature control switch LH and RH.
Temperature control with temperature control switch LH and RH.
OK
NG