DEF mode damper servo motor sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the DEF mode damper servo motor2 to any position, which controls the air outlet changes.
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1455/55 | The air outlet damper position does not change even if the air conditioning amplifier assembly operates the DEF mode damper servo motor | ·
DEF mode damper servo motor ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Use the Data List to check if the DEF mode damper servo motor is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| A/O Damper DEF Pos(D Side) | DEF mode damper servo motor target pulse / Min.: 128, Max.: 383 | ·
FACE1: 258 (pulse) ·
FACE2: 258 (pulse) ·
B/L1: 277 (pulse) ·
FOOT-O: 290 (pulse) ·
FOOT-D: 290 (pulse) ·
FOOT-R: 290 (pulse) ·
FOOT-F: 307 (pulse) ·
F/D: 316 (pulse) ·
DEF: 328 (pulse) |
·
Displayed between 258 and 328 pulse ·
DEF mode damper servo motor system malfunction |
| A/O Damper DEF Actual Pos(D) | DEF mode damper servo motor actual pulse / Min.: 128, Max.: 383 | ·
FACE1: 258 (pulse) ·
FACE2: 258 (pulse) ·
B/L1: 277 (pulse) ·
FOOT-O: 290 (pulse) ·
FOOT-D: 290 (pulse) ·
FOOT-R: 290 (pulse) ·
FOOT-F: 307 (pulse) ·
F/D: 316 (pulse) ·
DEF: 328 (pulse) |
·
Displayed between 258 and 328 pulse ·
DEF mode damper servo motor system malfunction |
When the DEF mode switch is turned, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
E
Replace the DEF mode damper servo motor (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT (for RHD)>DISASSEMBLY).
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1455/55 is not output.
OK
NG
Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT (for RHD)>DISASSEMBLY).
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1455/55 is not output.
OK
NG
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1455/55 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG