The mode damper servo motor (rear) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the mode damper servo motor (rear) to any position, which controls the air outlet changes.
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1486/86 | The air outlet damper position does not change even if the air conditioning amplifier assembly operates the mode damper servo motor (rear). | ·
Mode damper servo motor (rear) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
w/ Rear Heater:
w/o Rear Heater:
Use the Data List to check if the mode damper servo motor (rear) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Outlet Servo Pls (F&R D) | Mode damper servo motor (rear) target pulse / Min.: 128, Max.: 383 | ·
FACE1: 258 (pulse) ·
FACE2: 258 (pulse) ·
B/L1: 277 (pulse) ·
FOOT-O: 290 (pulse) ·
FOOT-D: 290 (pulse) ·
FOOT-R: 290 (pulse) ·
FOOT-F: 307 (pulse) ·
F/D: 316 (pulse) ·
DEF: 328 (pulse) |
·
Displayed between 258 and 328 pulse ·
Mode damper servo motor (rear) system malfunction |
| A/O Servo Actual Plse(F&R D) | Mode damper servo motor (rear) actual pulse / Min.: 128, Max.: 383 | ·
FACE1: 258 (pulse) ·
FACE2: 258 (pulse) ·
B/L1: 277 (pulse) ·
FOOT-O: 290 (pulse) ·
FOOT-D: 290 (pulse) ·
FOOT-R: 290 (pulse) ·
FOOT-F: 307 (pulse) ·
F/D: 316 (pulse) ·
DEF: 328 (pulse) |
·
Displayed between 258 and 328 pulse ·
Mode damper servo motor (rear) system malfunction |
When the rear mode switch is turned, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
E
Replace the mode damper servo motor (rear) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT (for LHD)>DISASSEMBLY).
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1486/86 is not output.
OK
NG
Replace the air conditioning harness assembly with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT (for LHD)>DISASSEMBLY).
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1486/86 is not output.
OK
NG
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG