The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects output current from the solar sensor.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B14A2 | An open or short in the driver side solar sensor circuit. | ·
Automatic light control sensor (solar sensor) ·
Harness or connector between solar sensor and air conditioning amplifier assembly ·
Harness or connector between solar sensor and main body ECU (cowl side junction block LH) ·
Main body ECU (cowl side junction block LH) ·
Air conditioning amplifier assembly |
If DTC B1244 is output at the same time, troubleshoot DTC B1244 first.
Use the Data List to check if the driver side solar sensor is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Solar Sensor (D Side) | Driver side solar sensor /
Min.: 0, Max.: 255 |
Driver side solar sensor voltage increases as brightness increases | Open in the circuit: 0.
Short in the circuit: 255. |
The display is as specified in the normal condition.
OK
NG
w/ Rear Heater
Disconnect the F9 sensor connector.
Disconnect the E35 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E35-7 (TSD) - F9-1 (TSL)*1 | Always | Below 1 Ω |
| E35-7 (TSD) - F9-2 (TSR)*2 | Always | Below 1 Ω |
| E35-7 (TSD) - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
w/o Rear Heater
Disconnect the F9 sensor connector.
Disconnect the E81 amplifier connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-33 (TSD) - F9-1 (TSL)*1 | Always | Below 1 Ω |
| E81-33 (TSD) - F9-2 (TSR)*2 | Always | Below 1 Ω |
| E81-33 (TSD) - Body ground | Always | 10 kΩ or higher |
*1: for LHD
*2: for RHD
OK
NG
Remove the automatic light control sensor (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).
Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (TSL) - 3 (CLTE)*1 | Sensor exposed to electric light | 0.8 to 4.3 V |
| Sensor covered with a cloth | Below 0.8 V | |
| 2 (TSR) - 3 (CLTE)*2 | Sensor exposed to electric light | 0.8 to 4.3 V |
| Sensor covered with a cloth | Below 0.8 V |
As the inspection light is moved away from the sensor, the voltage decreases.
Use an incandescent light for inspection. Bring it about 300 mm (11.8 in.) from the solar sensor.
*1: for LHD
*2: for RHD
OK
NG
Disconnect the E2 ECU connector.
Disconnect the F9 sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E2-20 (CLTB) - F9-6 (CLTB) | Always | Below 1 Ω |
| E2-19 (CLTS) - F9-5 (CLTS) | ||
| E2-18 (CLTE) - F9-3 (CLTE) | ||
| E2-20 (CLTB) - Body ground | Always | 10 kΩ or higher |
| E2-19 (CLTS) - Body ground | ||
| E2-18 (CLTE) - Body ground |
OK
NG