Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255699 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A3  Front Passenger Side Solar Sensor Short Circuit  


DESCRIPTION

E132508E30
0.438,0.177 2.427,0.427 1.99,0.25 10 false Output Current of Photodiode 0.354,0.792 0.813,1.042 0.458,0.25 10 false High 0.365,2.448 0.823,2.719 0.458,0.271 10 false Low 0.823,2.698 1.344,2.948 0.521,0.25 10 false Weak 2.198,2.688 2.75,2.958 0.552,0.271 10 false Strong 0.844,3 2.583,3.24 1.74,0.24 10 false Strength of Solar Radiation

The automatic light control sensor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in auto mode. The output current from the solar sensor varies according to the amount of sunlight. When the sunlight increases, the output current increases. As the sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects output current from the solar sensor.

DTC Code DTC Detection Condition Trouble Area
B14A3 An open or short in the passenger side solar sensor circuit.
·

Automatic light control sensor (solar sensor)

·

Harness or connector between solar sensor and air conditioning amplifier assembly

·

Harness or connector between solar sensor and main body ECU (cowl side junction block LH)

·

Main body ECU (cowl side junction block LH)

·

Air conditioning amplifier assembly



HINT:

If DTC B1244 is output at the same time, troubleshoot DTC B1244 first.


WIRING DIAGRAM

E160577E09
1.543,1.14 1.949,1.324 0.406,0.184 10 CLTB 2.01,1.075 2.157,1.258 0.147,0.184 10 6 4.783,0.955 4.980,1.115 0.197,0.160 10 20 4.771,0.331 5.045,0.491 0.274,0.160 10 E2 4.771,1.16 5.045,1.320 0.274,0.160 10 E2 4.771,0.745 5.045,0.905 0.274,0.160 10 E2 5.151,2.749 5.467,2.909 0.316,0.160 10 TSP 5.091,1.151 5.490,1.311 0.399,0.160 10 CLTB 4.763,1.664 4.989,1.824 0.225,0.160 10 2D 4.845,2.052 7.116,2.375 2.272,0.323 10 Main Body ECU (Cowl Side Junction Block LH) 4.863,3.22 7.151,3.404 2.287,0.185 10 Air Conditioning Amplifier Assembly 4.349,2.659 5.051,2.844 0.702,0.185 10 8*1, 32*2 4.87,3.061 5.815,3.245 0.945,0.185 10 E35*1, E81*2 0.671,2.282 2.663,2.624 1.992,0.342 10 Automatic Light Control Sensor (Passenger Side Solar Sensor) 0.038,3.17 1.339,3.346 1.301,0.176 10 *1: w/ Rear Heater 0.038,0.023 1.339,0.305 1.301,0.282 12 for LHD: 0.038,3.451 1.449,3.626 1.411,0.176 10 *2: w/o Rear Heater 4.783,0.145 4.980,0.305 0.197,0.160 10 18 4.783,0.558 4.980,0.718 0.197,0.160 10 19 4.769,1.475 5.057,1.634 0.288,0.160 10 62 5.409,1.577 5.549,1.737 0.140,0.160 10 4 2.01,0.259 2.157,0.443 0.147,0.184 10 3 2.01,0.67 2.157,0.854 0.147,0.184 10 5 2.01,1.564 2.676,1.748 0.666,0.184 10 2 1.543,0.344 1.949,0.528 0.406,0.184 10 CLTE 1.543,0.736 1.949,0.920 0.406,0.184 10 CLTS 1.575,1.648 2.011,1.832 0.436,0.184 10 TSR 5.092,0.332 5.498,0.516 0.406,0.184 10 CLTE 5.092,0.724 5.498,0.908 0.406,0.184 10 CLTS 5.606,1.695 6.012,1.878 0.406,0.184 10 GND2 0.68,2.134 0.900,2.289 0.221,0.156 10 F9

E160577E12
1.543,1.133 1.949,1.316 0.406,0.184 10 CLTB 2.01,1.067 2.157,1.251 0.147,0.184 10 6 4.783,0.948 4.980,1.107 0.197,0.160 10 20 4.771,0.323 5.045,0.483 0.274,0.160 10 E2 4.771,1.153 5.045,1.312 0.274,0.160 10 E2 4.771,0.738 5.045,0.897 0.274,0.160 10 E2 5.151,2.741 5.467,2.901 0.316,0.160 10 TSP 5.091,1.144 5.490,1.304 0.399,0.160 10 CLTB 4.763,1.657 4.989,1.816 0.225,0.160 10 2D 5.043,2.016 6.970,2.339 1.927,0.323 10 Main Body ECU (Cowl Side Junction Block LH) 4.863,3.212 7.151,3.397 2.287,0.185 10 Air Conditioning Amplifier Assembly 4.45,2.651 5.052,2.836 0.602,0.185 10 8*1, 32*2 4.87,3.053 5.815,3.238 0.945,0.185 10 E35*1, E81*2 0.82,2.274 2.812,2.617 1.992,0.342 10 Automatic Light Control Sensor (Passenger Side Solar Sensor) 0.038,3.163 1.296,3.338 1.257,0.176 10 *1: w/ Rear Heater 0.038,3.443 1.289,3.618 1.251,0.176 10 *2: w/o Rear Heater 4.783,0.137 4.980,0.297 0.197,0.160 10 18 4.783,0.55 4.980,0.710 0.197,0.160 10 19 4.781,1.467 4.978,1.627 0.197,0.160 10 62 5.429,1.579 5.627,1.739 0.197,0.160 10 4 2.01,0.252 2.157,0.435 0.147,0.184 10 3 2.01,0.663 2.157,0.846 0.147,0.184 10 5 2.01,1.556 2.157,1.740 0.147,0.184 10 1 1.543,0.336 1.949,0.520 0.406,0.184 10 CLTE 1.543,0.728 1.949,0.912 0.406,0.184 10 CLTS 1.622,1.64 1.926,1.824 0.304,0.184 10 TSL 5.092,0.324 5.498,0.508 0.406,0.184 10 CLTE 5.092,0.716 5.498,0.900 0.406,0.184 10 CLTS 5.606,1.687 6.012,1.871 0.406,0.184 10 GND2 0.829,2.126 1.050,2.282 0.221,0.156 10 F9 0.044,0 0.908,0.316 0.864,0.316 12 for RHD:

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (PASSENGER SIDE SOLAR SENSOR)
a.

Use the Data List to check if the front passenger side solar sensor is functioning properly.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (P Side) Passenger side solar sensor /
Min.: 0, Max.: 255
Passenger side solar sensor voltage increases as brightness increases Open in the circuit: 0.
Short in the circuit: 255.

OK:

The display is as specified in the normal condition.




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AUTOMATIC LIGHT CONTROL SENSOR)
E349755E02
0.833,1.667 1.125,1.917 0.292,0.25 5.875,1.083 6.198,1.323 0.323,0.24 1.146,2.417 1.563,2 false 1.844,1.958 2.26,1.542 false 5.75,3.313 5.844,3.313 5.844,3.313 6.375,2.542 false 0.177,0.167 2.479,0.583 2.302,0.417 10 false Front view of wire harness connector: (to Automatic Light Control Sensor) 3.823,0.156 6.271,0.573 2.448,0.417 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 0.896,1.719 1.208,1.917 0.313,0.198 10 false F9 0.708,2.375 1.229,2.604 0.521,0.229 10 false TSL*2 2.313,1.458 2.833,1.688 0.521,0.229 10 false TSR*1 5.906,1.135 6.198,1.313 0.292,0.177 10 true E35 5.417,3.229 5.771,3.448 0.354,0.219 10 false TSP 3.969,2.958 4.781,3.177 0.813,0.219 10 false *1: for LHD 3.979,3.313 4.792,3.531 0.813,0.219 10 false *2: for RHD

a.

w/ Rear Heater

i.

Disconnect the F9 sensor connector.


ii.

Disconnect the E35 amplifier connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E35-8 (TSP) - F9-2 (TSR)*1 Always Below 1 Ω
E35-8 (TSP) - F9-1 (TSL)*2 Always Below 1 Ω
E35-8 (TSP) - Body ground Always 10 kΩ or higher


HINT:

*1: for LHD

*2: for RHD




b.

w/o Rear Heater

E349756E02
0.708,1.281 1.01,1.5 0.302,0.219 5.469,0.854 5.823,1.073 0.354,0.219 1.115,2.031 1.531,1.615 false 1.802,1.563 2.219,1.146 false 5.198,2.458 5.344,2.458 5.344,2.458 5.458,2.021 false 0.125,0.115 2.438,0.51 2.313,0.396 10 false Front view of wire harness connector: (to Automatic Light Control Sensor) 3.927,0.146 6.365,0.531 2.438,0.385 10 false Rear view of wire harness connector: (to Air Conditioning Amplifier Assembly) 0.771,1.302 1.083,1.5 0.313,0.198 10 false F9 0.896,2.052 1.375,2.25 0.479,0.198 10 false TSL*2 2.292,1.052 2.771,1.25 0.479,0.198 10 false TSR*1 5.531,0.885 5.844,1.083 0.313,0.198 10 false E81 4.906,2.365 5.24,2.563 0.333,0.198 10 false TSP 3.938,2.427 4.677,2.635 0.74,0.208 10 false *2: for RHD 3.938,2.125 4.677,2.333 0.74,0.208 10 false *1: for LHD

i.

Disconnect the F9 sensor connector.


ii.

Disconnect the E81 amplifier connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-32 (TSP) - F9-2 (TSR)*1 Always Below 1 Ω
E81-32 (TSP) - F9-1 (TSL)*2 Always Below 1 Ω
E81-32 (TSP) - Body ground Always 10 kΩ or higher


HINT:

*1: for LHD

*2: for RHD





OK

3.INSPECT AUTOMATIC LIGHT CONTROL SENSOR (TSR, TSL - CLTE VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AUTOMATIC LIGHT CONTROL SENSOR (TSR, TSL - CLTE VOLTAGE)
E108193E40
1.906,1.385 2.521,1.625 false 1.49,1.219 0.906,0.917 false 1.5,1.573 0.875,1.281 false 1.906,1.198 2.333,0.979 false 0.406,0.792 0.906,1.021 0.5,0.229 10 false TSR*1 2.438,0.865 2.938,1.094 0.5,0.229 10 false TSL*2 2.583,1.573 3.104,1.802 0.521,0.229 10 false CLTE 0.458,1.188 0.875,1.417 0.417,0.229 10 false CLTB 0.281,0.115 2.552,0.458 2.271,0.344 10 false Component with harness connected: (Automatic Light Control Sensor) 0.073,1.563 0.802,1.75 0.729,0.188 10 false *1: for LHD 0.073,1.885 0.813,2.073 0.74,0.188 10 false *2: for RHD

a.

Remove the automatic light control sensor (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Apply battery voltage between terminals 6 (CLTB) and 3 (CLTE) of the solar sensor.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (TSR) - 3 (CLTE)*1 Sensor exposed to electric light 0.8 to 4.3 V
Sensor covered with a cloth Below 0.8 V
1 (TSL) - 3 (CLTE)*2 Sensor exposed to electric light 0.8 to 4.3 V
Sensor covered with a cloth Below 0.8 V


HINT:
·

As the inspection light is moved away from the sensor, the voltage decreases.

·

Use an incandescent light for inspection. Bring it about 300 mm (11.8 in.) from the solar sensor.

·

*1: for LHD

·

*2: for RHD





OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
U165922E02
2.448,1.688 2.75,1.823 false 2.26,1.698 2.385,2.156 false 2.115,1.708 1.958,2.167 false 1.229,3.917 1.542,3.844 false 1.552,4.073 1.333,4.292 false 1.906,4.073 2.063,4.281 false 0.083,0.094 2.406,0.448 2.323,0.354 10 false Front view of wire harness connector: (to Main Body ECU) 0.125,2.521 2.417,2.906 2.292,0.385 10 false Front view of wire harness connector: (to Automatic Light Control Sensor) 2.802,1.75 3.302,1.958 0.5,0.208 10 false CLTB 2.073,4.292 2.573,4.5 0.5,0.208 10 false CLTB 2.323,2.156 2.823,2.365 0.5,0.208 10 false CLTS 0.969,4.292 1.354,4.5 0.385,0.208 10 false CLTS 1.594,2.167 2.021,2.375 0.427,0.208 10 false CLTE 0.385,1.469 0.688,1.677 0.302,0.208 10 false E2 0.844,3.875 1.229,4.083 0.385,0.208 10 false CLTE 0.854,3.479 1.156,3.688 0.302,0.208 10 false F9

a.

Disconnect the E2 ECU connector.


b.

Disconnect the F9 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-20 (CLTB) - F9-6 (CLTB) Always Below 1 Ω
E2-19 (CLTS) - F9-5 (CLTS)
E2-18 (CLTE) - F9-3 (CLTE)
E2-20 (CLTB) - Body ground Always 10 kΩ or higher
E2-19 (CLTS) - Body ground
E2-18 (CLTE) - Body ground




OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR