The mode damper servo motor sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the mode damper servo motor to any position, which controls the air outlet changes.
Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1443/43 | The air outlet damper position does not change even if the air conditioning amplifier assembly operates the air outlet damper servo motor. | ·
Mode damper servo motor ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Use the Data List to check if the mode damper servo motor is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Outlet Servo Pulse (D) | Mode damper servo motor target pulse / Min.: 128, Max.: 383 | ·
FACE: 254 (pulse) ·
FACE1: 246 (pulse) ·
FACE2: 254 (pulse) ·
B/L1: 230 (pulse) ·
B/L2: 218 (pulse) ·
FOOT-O: 208 (pulse) ·
FOOT-D: 189 (pulse) ·
FOOT-R: 178 (pulse) ·
FOOT-F: 178 (pulse) ·
FOOT 178 (pulse) ·
F/D: 155 (pulse) ·
DEF: 143 (pulse) |
·
Displayed between 143 and 254 pulse ·
Mode damper servo motor system malfunction |
| Air Outlet Servo Actu Pulse(D) | Mode damper servo motor actual pulse / Min.: 128, Max.: 383 | ·
FACE: 254 (pulse) ·
FACE1: 246 (pulse) ·
FACE2: 254 (pulse) ·
B/L1: 230 (pulse) ·
B/L2: 218 (pulse) ·
FOOT-O: 208 (pulse) ·
FOOT-D: 189 (pulse) ·
FOOT-R: 178 (pulse) ·
FOOT-F: 178 (pulse) ·
FOOT 178 (pulse) ·
F/D: 155 (pulse) ·
DEF: 143 (pulse) |
·
Displayed between 143 and 254 pulse ·
Mode damper servo motor LH system malfunction |
When the driver side mode switch is turned, the actual pulse changes following the target pulse.
| Result | Proceed to |
|---|---|
| Target pulse changes but actual pulse does not change | A |
| Target pulse and actual pulse do not change | B |
| Actual pulse changes following the target pulse (When troubleshooting according to the DTC) | C |
| Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) | D |
A
B
C
D
Replace the mode damper servo motor.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443/43 is not output.
OK
B
Replace the air conditioning harness assembly with a new or known good one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443/43 is not output.
OK
NG
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443/43 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG