Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

E350120E01
0.323,0.198 1.198,0.417 0.875,0.219 10 false Blower Level 0.729,0.573 1.021,0.781 0.292,0.208 10 false HI 0.719,1.052 1.01,1.26 0.292,0.208 10 false M 0.698,1.51 0.99,1.719 0.292,0.208 10 false LO 0.906,2.167 1.198,2.375 0.292,0.208 10 false 0 1.375,2.156 1.667,2.365 0.292,0.208 10 false Low 2.25,2.156 2.542,2.365 0.292,0.208 10 false High 1.406,2.427 2.281,2.646 0.875,0.219 10 false SI Duty (%) 3.896,0.667 5.021,0.885 1.125,0.219 10 false Duty Ratio (%) = 5.281,0.542 5.573,0.75 0.292,0.208 10 false T1 5.281,0.781 5.573,0.99 0.292,0.208 10 false T2 5.938,0.656 6.229,0.865 0.292,0.208 10 false 100 5.042,1.198 5.333,1.406 0.292,0.208 10 false T1 5.198,2.135 5.49,2.344 0.292,0.208 10 false T2 4.542,1.552 4.833,1.76 0.292,0.208 10 false Off 4.542,1.802 4.833,2.01 0.292,0.208 10 false On

The blower with fan motor sub-assembly operates according to signals from the air conditioning amplifier assembly. The blower with fan motor sub-assembly speed signals are transmitted by changes in the duty ratio.

Duty Ratio:

The duty ratio is the ratio of the blower with fan motor sub-assembly on time (T1) to the total of the blower with fan motor sub-assembly on and off time (T2).

The air conditioning amplifier assembly controls the blower with fan motor sub-assembly speed.

WIRING DIAGRAM

E185637E08
1.079,0.711 1.318,0.894 0.239,0.184 10 SI 1.051,1.652 1.318,1.845 0.267,0.193 10 +B 0.93,2.247 1.317,2.421 0.387,0.174 10 GND 1.342,0.604 1.572,0.815 0.230,0.211 10 2 1.342,1.552 1.572,1.764 0.230,0.211 10 3 1.342,2.17 1.572,2.381 0.230,0.211 10 1 0.207,2.9 0.567,3.066 0.360,0.165 10 A29 0.193,3.064 2.562,3.294 2.369,0.230 10 Blower with Fan Motor Sub-assembly 2.92,1.663 4.259,1.916 1.339,0.253 10 from HTR H-Fuse 5.619,0.576 5.831,0.745 0.211,0.170 10 23 5.596,2.201 5.807,2.371 0.211,0.170 10 14 5.9,0.69 6.223,0.860 0.323,0.170 10 BLW 5.9,2.321 6.320,2.519 0.420,0.198 10 GND 5.508,2.779 5.928,2.977 0.420,0.198 10 E81 5.508,2.939 7.122,3.289 1.614,0.350 10 Air Conditioning Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BLOWER MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Blower with fan motor sub-assembly operates and blower with fan motor sub-assembly speed changes.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
a.
U166083E01
0.107,0.036 0.284,0.192 0.177,0.156 10 *a 0.511,1.149 0.810,1.311 0.298,0.163 10 A29 0.705,1.673 1.038,1.818 0.333,0.145 10 GND 1.345,1.596 1.096,1.716 false 2.415,1.81 2.748,1.956 0.333,0.145 10 +B 2.05,1.596 2.372,1.828 false

Disconnect the A29 blower with fan motor sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-3 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blower with Fan Motor Sub-assembly)


OK

3.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - AIR CONDITIONING AMPLIFIER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Disconnect the A29 blower with fan motor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-23 (BLW) - A29-2 (SI) Always Below 1 Ω
E81-23 (BLW) - Body ground Always 10 kΩ or higher
E81-14 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U166104E01
0.163,0.162 0.347,0.332 0.184,0.170 10 *a 1.586,0.327 1.900,0.492 0.313,0.165 10 E81 0.496,0.46 0.846,0.606 0.350,0.147 10 GND 2.886,3.886 3.236,4.033 0.350,0.147 10 GND 2.312,2.05 2.662,2.196 0.350,0.147 10 BLW 1.362,1.376 0.889,0.619 false

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) E81-23 (BLW) - E81-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Ignition switch ON
Blower switch LO level

OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

HINT:

Waveform varies with the blower level.




OK

5.REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.REPLACE BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Temporarily replace the blower with fan motor sub-assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL).



NEXT

6.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
6.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Operate the blower with fan motor sub-assembly to check that it functions properly.

OK:

Blower with fan motor sub-assembly operates normally.




OK

END (BLOWER WITH FAN MOTOR SUB-ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY