The air conditioning harness assembly connects the air conditioning amplifier assembly and each servo motor. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends the damper position information to the air conditioning amplifier assembly.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1497/97 | An open or error in the communication line. | ·
Air conditioning harness assembly ·
No. 2 air conditioning harness assembly ·
Air mix damper servo motor ·
Damper servo motor (REC/FRS) ·
Cool bypass damper servo motor ·
Mode damper servo motor ·
Air conditioning amplifier assembly ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1497/97 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-14 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E81-21 (+B1) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
OK
NG
Select the Active Test, use the GTS to generate a control command, and then check that the servo motors operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse(D) | Air mix damper servo motor pulse | Min.: 128, Max.: 383 | ·
Operates between 249 to 331 (for LHD) ·
Operates between 181 to 263 (for RHD) |
| Air Outlet Servo Pulse (D) | Mode damper servo motor Pulse | Min.: 128, Max.: 383 | Operates between 143 to 254 |
| Air Inlet Damper Targ Pulse | Mode damper servo motor (REC/FRS) pulse | Min.: 128, Max.: 383 | Operates between 258 to 286 |
| Cool Air Bypass Pulse | Cool bypass damper servo motor pulse | Min.: 128, Max.: 383 | Operates between 225 to 254 |
Arm of the damper servo motor selected in the Active Test moves smoothly.
| Result | Proceed to |
|---|---|
| Any front damper servo motor is malfunctioning | A |
| All front damper servo motors are malfunctioning | B |
A
B
Replace the malfunctioning damper servo motor connected to air conditioning harness assembly.
Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new one and check that the condition returns to normal.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1497/97 is not output.
OK
NG
Replace the air conditioning harness assembly with a new or known good one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1497/97 is not output.
OK
NG