Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1442 The air inlet damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 blower damper servo sub-assembly.
·

No. 1 blower damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E350098E01
3.135,1.083 3.448,1.281 0.313,0.198 10 false IC 5.313,0.385 5.49,0.615 0.177,0.229 10 false 4 5.302,0.958 5.479,1.188 0.177,0.229 10 false 3 5.323,1.51 5.5,1.74 0.177,0.229 10 false 2 5.573,0.51 6.063,0.708 0.49,0.198 10 false B BUS 5.552,1.052 6.042,1.25 0.49,0.198 10 false BUS 5.552,1.573 6.042,1.771 0.49,0.198 10 false BUS G 0.563,2.052 2.354,2.438 1.792,0.385 10 false No. 1 Blower Damper Servo Sub-assembly 2.844,2.094 5.125,2.333 2.281,0.24 10 false Air Conditioning Harness Assembly 5.594,2.021 5.958,2.219 0.365,0.198 10 false z54 5.583,2.198 6.813,2.594 1.229,0.396 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AIR INLET DAMPER TARG PULSE)
a.

Use the Data List to check if the No. 1 blower damper servo sub-assembly is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly target pulse / Min.: 0, Max.: 255
for LHD
·

Recirculation: 37 (pulse)

·

Fresh: 9 (pulse)


for RHD
·

Recirculation: 9 (pulse)

·

Fresh: 37 (pulse)


-

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to problem symptoms table) B
NG C



A

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
a.

Temporarily replace the No. 1 blower damper servo sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the No. 1 blower damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the No. 1 blower damper servo sub-assembly with a new or normally functioning one.




c.

Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1442 is not output A
DTC B1442 is output B



A

END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

B

3.CHECK AIR CONDITIONING HARNESS ASSEMBLY
3.CHECK AIR CONDITIONING HARNESS ASSEMBLY

A

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY