Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1443  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1443 The air outlet damper position does not change for 30 seconds or more when the air conditioning amplifier assembly operates the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo).
·

No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E350098E02
3.135,1.083 3.448,1.281 0.313,0.198 10 false IC 5.313,0.385 5.49,0.615 0.177,0.229 10 false 4 5.302,0.958 5.479,1.188 0.177,0.229 10 false 3 5.323,1.51 5.5,1.74 0.177,0.229 10 false 2 5.573,0.51 6.063,0.708 0.49,0.198 10 false B BUS 5.552,1.052 6.042,1.25 0.49,0.198 10 false BUS 5.552,1.573 6.042,1.771 0.49,0.198 10 false BUS G 0.563,2.052 2.354,2.438 1.792,0.385 10 false No. 1 Blower Damper Servo Sub-assembly 2.844,2.094 5.125,2.333 2.281,0.24 10 false Air Conditioning Harness Assembly 5.594,2.021 5.958,2.219 0.365,0.198 10 false z54 5.583,2.198 6.813,2.594 1.229,0.396 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AIR OUTLET SERVO PULSE [D])
a.

Use the Data List to check if the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) target pulse / Min.: 0, Max.: 255
·

FACE: 117 (pulse)

·

B/L: 93 (pulse)

·

FOOT: 41 (pulse)

·

F/D: 18 (pulse)

·

DEF: 6 (pulse)


-

OK:

The display is as specified in the normal condition column.


Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to problem symptoms table) B
NG C



A

2.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
a.

Temporarily replace the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo).


HINT:

Since the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the No. 1 air conditioning radiator damper servo sub-assembly (mode damper servo) with a new or normally functioning one.




c.

Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1443 is not output A
DTC B1443 is output B



A

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

B

3.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
3.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

A

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY