Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052847 HEATING / AIR CONDITIONING _0255703 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Control Panel Circuit  


DESCRIPTION

This circuit consists of the air conditioning control assembly and air conditioning amplifier assembly. When the air conditioning control assembly is operated, signals are transmitted to the air conditioning amplifier assembly through the LIN communication system.

If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate when the air conditioning control assembly is operated.

WIRING DIAGRAM

E157369E47
5.564,0.845 5.874,1.026 0.310,0.181 10 LIN1 1.389,0.845 1.741,1.026 0.353,0.181 10 LIN1 1.463,1.364 1.708,1.545 0.245,0.181 10 IG+ 1.407,1.911 1.732,2.092 0.326,0.181 10 GND 3.744,1.376 5.225,1.550 1.481,0.174 10 from IG1 NO.3 Relay 2.419,1.515 3.335,1.696 0.916,0.181 10 ECU-IG No.2 5.525,2.648 6.991,3.054 1.467,0.406 10 Air Conditioning Amplifier Assembly 5.525,2.47 5.853,2.639 0.328,0.169 10 E81 0.671,2.62 2.076,2.953 1.405,0.333 10 Air Conditioning Control Assembly 0.886,3.296 2.501,3.477 1.615,0.181 10 : LIN Communication Line 5.255,0.676 5.426,0.857 0.171,0.181 10 37 1.833,1.256 1.989,1.437 0.156,0.181 10 7 1.833,1.811 1.989,1.992 0.156,0.181 10 1 1.83,0.653 2.016,0.835 0.186,0.181 10 5 0.671,2.446 1.169,2.630 0.498,0.184 10 F10

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING CONTROL)
a.

Disconnect the E81 air conditioning amplifier assembly connector.


b.

Disconnect the F10 air conditioning control assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E81-37 (LIN1) - F10-5 (LIN1) Always Below 1 Ω
F10-5 (LIN1) - Body ground Always 10 kΩ or higher




OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BATTERY AND BODY GROUND)
a.
U166236E01
0.177,0.055 0.388,0.242 0.212,0.187 10 *a 0.333,0.858 0.618,1.029 0.285,0.171 10 F10 0.533,1.67 0.932,1.841 0.398,0.171 10 GND 3.047,0.191 3.299,0.362 0.252,0.171 10 IG+ 1.144,1.064 0.789,1.642 false 2.688,0.991 3.014,0.285 false

Disconnect the F10 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F10-7 (IG+) - F10-1 (GND) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Control Assembly)



OK

3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE AIR CONDITIONING CONTROL ASSEMBLY
a.

Temporarily replace the air conditioning control assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL(w/o Multi-display)>DISASSEMBLY).



NEXT

4.CHECK AIR CONDITIONING CONTROL ASSEMBLY
4.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Operate the air conditioning control assembly to check that it functions properly.

OK:

Air conditioning control assembly operates normally.




OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY