Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (w/ Sliding Roof) › from 2015.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255720 ROOF HEADLINING(w/ Sliding Roof) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(w/ Sliding Roof)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 62597A 1.INSTALL SIDE TRIM BOX

B185343

a.

Install the side trim box with the 9 screws.


Hide 62598D 2.INSTALL SIDE TRIM BOX COVER

a.

Install the side trim box cover.


Hide 62605Q 3.INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH

a.

Install the quarter trim lid sub-assembly RH.


Hide 62522A 4.INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

B188391

a.

Attach the 6 clips to install the quarter trim cover LH.


Hide 62521B 5.INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 71866B 6.INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B181698

a.

Attach the 6 clips to install the rear No. 2 seat cover bezel.


Hide 71865A 7.INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the rear No. 2 seat cover bezel.


Hide 72058C 8.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

Hide 72057A 9.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 62526D 10.INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182421

a.

Attach the 4 claws to install the No. 2 side trim base cover LH.


Hide 62516B 11.INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

HINT:

Use the same procedures described for the LH side.


Hide 62525D 12.INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182420

a.

Attach the 4 claws to install the No. 1 side trim base cover LH.


Hide 62515B 13.INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

B187176

a.

Attach the 4 claws to install the No. 1 side trim base cover RH.


b.
B185344

Install the duct with the 6 screws.


Hide 66992 14.INSTALL NO. 2 CUP HOLDER

B182417

a.

Attach the 3 claws to install the No. 2 cup holder.


b.

Install the 5 screws.


Hide 66991B 15.INSTALL NO. 1 CUP HOLDER

B182419

a.

Attach the 3 claws to install the No. 1 cup holder.


b.

Install the 5 screws.


Hide 62502B 16.INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH

B182415

a.

Attach the 4 claws to install the quarter trim cover sub-assembly LH.


b.

Install the 7 screws.


c.
B182411

w/ Rear Heater:

Install the duct with the 8 screws.


Hide 62501C 17.INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH

B182413

a.

Attach the 4 claws to install the quarter trim cover sub-assembly RH.


b.

Install the 7 screws.


Hide 73372C 18.INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH

U155799E01
2.381,0.542 2.572,0.721 0.192,0.179 10 *a 2.71,0.505 2.902,0.684 0.192,0.179 10 *a

a.

Install the rear No. 2 seat shoulder belt hanger LH with new 2 spring nuts.

Text in Illustration
*a Spring Nut


Hide 73371C 19.INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH

HINT:

Use the same procedures described for the LH side.


Hide 73371A 20.INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedure for both rear No. 1 seat shoulder belt hangers.


a.
U155800E01
1.556,0.157 1.748,0.336 0.192,0.179 10 *a 1.156,0.229 1.348,0.408 0.192,0.179 10 *a

Install the rear No. 1 seat shoulder belt hanger with new 2 spring nuts.

Text in Illustration
*a Spring Nut


Hide 62488A 21.INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182427

a.

Attach the 7 claws to install the roof side inner garnish cover LH.


Hide 62487A 22.INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 73034 23.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182423

a.

Attach the 6 claws to install the rear shoulder belt anchor plate sub-assembly LH.


Hide 73033 24.INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 73024 25.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182425

a.

Slide the front shoulder belt anchor plate sub-assembly LH in the direction shown in the illustration and attach the 6 claws to install the front shoulder belt anchor plate sub-assembly LH.


Hide 73023 26.INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 67916 27.INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

B181675

a.

Attach the 3 clips to install the rear door scuff plate outside LH.


Hide 67915 28.INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

HINT:

Use the same procedures described for the LH side.


Hide 67912A 29.INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

B181683

a.

Attach the 4 clips to install the front door scuff plate outside LH.


Hide 67911B 30.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 67881A 31.INSTALL BACK DOOR WEATHERSTRIP

U155857E04
1.948,1.646 2.458,1.896 false 2.5,1.823 2.688,2 0.188,0.177 10 false *a 0.656,2.875 0.844,3.052 0.188,0.177 10 false *b

a.

Install the back door weatherstrip as shown in the illustration.

Text in Illustration
*a Alignment Mark
*b Mark


Hide 62332A 32.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

U155807E05
1.573,2.427 1.542,2.24 false 1.458,2.052 1.646,2.229 0.188,0.177 10 false *a 0.531,3.021 0.719,3.198 0.188,0.177 10 false *b

a.

Install the rear door opening trim weatherstrip LH as shown in the illustration.

Text in Illustration
*a Alignment Mark
*b Mark


Hide 62331A 33.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 62312B 34.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

U155806E04
1.573,2.427 1.5,2.24 false 1.385,2.021 1.573,2.198 0.188,0.177 10 false *a 0.563,3.042 0.75,3.219 0.188,0.177 10 false *b

a.

Install the front door opening trim weatherstrip LH as shown in the illustration.

Text in Illustration
*a Alignment Mark
*b Mark


Hide 62311B 35.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 36.INSTALL ROOF HEADLINING ASSEMBLY

B183934

HINT:
·

for Manual Seat:

When installing the roof headlining assembly, move the front seat and rear No. 1 seat to the position shown in the illustration.

·

for Power Seat:

When installing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

·

for Power Seat:

After moving the seats, disconnect the cable from the negative (-) battery terminal.



a.
B181716

Place the roof headlining assembly in the cabin from the rear of the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when placing it in the cabin.



b.

for 3 Person Seat Type Rear No. 2 Seat:

Attach the 12 claws, 2 clips, 2 guides and 16 fasteners to install the headlining.

U164097E03
1.927,0.823 1.125,0.823 true 1.927,2.542 1.115,2.542 true 0.927,0.729 1.115,0.906 0.188,0.177 10 false *a 0.927,2.458 1.115,2.635 0.188,0.177 10 false *a 0.146,0.083 0.375,0.26 0.229,0.177 10 false *A

Text in Illustration
*A for 3 Person Seat Type Rear No. 2 Seat - -
*a Guide - -


c.

except 3 Person Seat Type Rear No. 2 Seat:

Attach the 12 claws, 3 clips, 2 guides and 16 fasteners to install the headlining.

U164098E04
1.927,0.813 1.094,0.813 true 1.927,2.563 1.083,2.563 true 0.896,0.729 1.083,0.906 0.188,0.177 10 false *a 0.896,2.469 1.083,2.646 0.188,0.177 10 false *a 0.146,0.031 0.438,0.208 0.292,0.177 10 false *A

Text in Illustration
*A except 3 Person Seat Type Rear No. 2 Seat - -
*a Guide - -


d.
U155789E02
0.125,0.052 0.313,0.229 0.188,0.177 10 false *a

Connect the washer hose.

Text in Illustration
*a Rear Left Side


e.
U155788E01
0.094,0.012 0.286,0.191 0.192,0.179 10 *a

Connect the antenna cord connector.

Text in Illustration
*a Rear Right Side


f.
U155786E02
0.104,0.146 0.292,0.323 0.188,0.177 10 false *a

Connect the antenna cord connector and attach the 2 clamps.


g.

Install the bolt.

Text in Illustration
*a Front Right Side


h.
U155787E02
2.198,0.833 2.25,1.073 false 0.135,0.135 0.323,0.313 0.188,0.177 10 false *a 2.073,0.635 2.26,0.813 0.188,0.177 10 false *b

Connect the 3 roof wire connectors and washer hose.


i.

Attach the 4 clamps.

Text in Illustration
*a Front Left Side
*b Washer Hose


j.
B181722

Connect the connector.


k.

w/ Pre-crash Safety System:

i.
B430359

w/o Camera Heater:

Connect the 2 connectors.


ii.
B478233

w/ Camera Heater:

Connect the 3 connectors.



l.
B430358

w/ Rain Sensor:

Connect the connector.


m.
B430357

w/ EC Mirror:

Connect the connector.


Hide 62432C 37.INSTALL FRONT ROOF SIDE RAIL GARNISH LH

U155802E02
1.479,2.417 1.896,2.417 false 1.938,2.333 2.125,2.51 0.188,0.177 10 false *a

a.

Install 3 new clips to the front roof side rail garnish LH.

Text in Illustration
*a New Clip


b.

Attach the 3 clips to install the front roof side rail garnish LH.


Hide 62431C 38.INSTALL FRONT ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 74630B 39.INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedure for both 3rd seat assist grip assemblies.


a.
B165740

Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.


b.

Install the 3rd seat assist grip assembly.


Hide 74610K 40.INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH

a.

w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

Install the No. 2 assist grip assembly.

i.
B169217

Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.


ii.

Install the No. 2 assist grip assembly LH.



b.

w/ Rear No. 2 Seat, for Face to Face Seat Type:

Install the No. 2 assist grip assembly.

i.
B165740

Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.


ii.

Install the No. 2 assist grip assembly LH.



Hide 74610B 41.INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74610U 42.INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both assist grip assemblies.


a.
B165740

Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.


b.

Install the assist grip assembly.


Hide 73139B 43.INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

B181709

a.

Attach the 4 guides and 4 clips to install the seat belt anchor cover.


Hide 86466D 44.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466E 45.INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 89943 46.INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

Hide 87834 47.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 74330C 48.INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

B189887

a.

Attach the 2 clips to install the center visor assembly LH.


Hide 74330B 49.INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

HINT:

Use the same procedures described for the LH side.


Hide 74348 50.INSTALL VISOR HOLDER

HINT:

Use the same procedure for visor holders.


a.
B151383

Attach the 2 claws.


b.

Push the visor holder in to install it.


Hide 74320 51.INSTALL VISOR ASSEMBLY LH

B181707

a.

Install the visor assembly LH with the 2 screws.


Hide 74310 52.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74325 53.INSTALL VISOR BRACKET COVER

HINT:

Use the same procedure for visor bracket covers.


a.
B181706

Attach the 4 claws to install the visor bracket cover.


Hide 81290 54.INSTALL NO. 3 ROOM LIGHT ASSEMBLY

Hide 81240 55.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 62472D 57.INSTALL REAR UPPER PILLAR GARNISH LH

B181702

a.

Attach the 5 clips to install the rear upper pillar garnish LH.


b.
B183809

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Install the seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.
B183996

Attach the 2 claws to close the seat belt shoulder anchor cover.



Hide 62471D 58.INSTALL REAR UPPER PILLAR GARNISH RH

B184328

a.

w/o Power Back Door:

i.

Attach the 5 clips to install the rear upper pillar garnish RH.



b.
U157046E01
2.985,1.405 3.093,2.151 false 3.033,2.176 3.225,2.355 0.192,0.179 10 *a

w/ Power Back Door:

i.

Pass the power back door rod through the rear upper pillar garnish RH.

Text in Illustration
*a Power Back Door Rod


ii.

Attach the 5 clips to install the rear upper pillar garnish RH.



c.
B195963

Install the seat belt shoulder anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.
B187190

Attach the 2 claws to close the seat belt shoulder anchor cover.


Hide 67847 59.INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

Hide 67937B 60.INSTALL BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

Hide 67939B 61.INSTALL BACK DOOR GARNISH CENTER (w/ Power Back Door)

Hide 62639 62.INSTALL REAR FRONT QUARTER TRIM GARNISH LH

B181703

a.

Pass the seat belt anchor through the rear front quarter trim garnish LH.


b.

Attach the clip and 2 guides to install the rear front quarter trim garnish LH.


c.

Install the screw.


Hide 62638 63.INSTALL REAR FRONT QUARTER TRIM GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62520P 64.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644

HINT:

When installing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

w/o Rear Air Conditioning System:

Connect the rear seat lock control lever cable.


ii.

w/ Rear Air Conditioning System:

Connect the thermistor connector and rear seat lock control lever cable.


iii.

Attach the 18 clips and 2 claws to install the front quarter trim panel assembly LH.


iv.

Install the clip and bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

B186889



b.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Attach the 18 clips and 2 claws to install the front quarter trim panel assembly LH.


ii.

Install the clip.

B190221



c.
U155783E04
1.906,1.073 2.479,0.292 true 1.313,1.49 1.365,1.76 false 1.323,1.833 1.51,2.01 0.188,0.177 10 false *a 2.552,0.083 2.74,0.26 0.188,0.177 10 false *a

w/ Rear No. 2 Seat, except Face to Face Seat Type:

Install the rear No. 2 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.


Text in Illustration
*a Protruding Part


d.
B181689

Install the rear No. 1 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.
B181687

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 62510P 65.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:

When installing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

w/o Rear Air Conditioning System:

Connect the rear seat lock control lever cable.


ii.

w/ Rear Air Conditioning System:

Connect the thermistor connector and rear seat lock control lever cable.


iii.

Attach the 16 clips and 2 claws to install the front quarter trim panel assembly RH.


iv.

Install the clip and bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

B186890



b.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Attach the 16 clips and 2 claws to install the front quarter trim panel assembly RH.


ii.

Install the clip.

B190220



c.
B181693

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Install the rear No. 2 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.
B181692

Attach the 3 claws to install the outer lap belt anchor cover.



d.
B181690

Install the rear No. 1 seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.
B181688

Attach the 3 claws to install the outer lap belt anchor cover.


Hide 71845B 66.INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedure for rear seat cover caps.


a.
B190186

Attach the 3 claws to install the rear seat cover cap.


Hide 62412 67.INSTALL CENTER PILLAR GARNISH LH

B181681

a.

Pass the seat belt anchor through the center pillar garnish LH.


b.

Attach the 2 clips and 2 guides to install the center pillar garnish LH.


c.

Install the bolt.


Hide 62411 68.INSTALL CENTER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 74620A 69.INSTALL REAR ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both rear assist grip assemblies.


a.
B181680

Attach the 2 claws to install the rear assist grip assembly.


b.

Install the 2 bolts.


c.
B181679

Attach the 4 claws to install the 2 assist grip plugs.


Hide 62414A 70.INSTALL CENTER LOWER PILLAR GARNISH LH

HINT:
·

for Manual Seat:

When installing the center lower pillar garnish LH, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When installing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181678

Attach the 2 claws and 7 clips to install the center lower pillar garnish LH.


b.
B181677

Install the seat belt anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62413A 71.INSTALL CENTER LOWER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62422 72.INSTALL CENTER PILLAR GARNISH COVER LH

HINT:
·

for Manual Seat:

When installing the center pillar garnish cover LH, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When installing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181676

Attach the 2 clips and 2 guides to install the center pillar garnish cover LH.


Hide 62421 73.INSTALL CENTER PILLAR GARNISH COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 62212 74.INSTALL FRONT PILLAR GARNISH LH

B185447

a.

w/ Speaker:

Connect the speaker connector.


b.

Attach the clip and 3 guides to install the front pillar garnish LH.


Hide 62211 75.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 74610A 76.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both assist grip sub-assemblies.


a.
B181685

Attach the 2 claws to install the assist grip sub-assembly.


b.

Install the 2 bolts.


c.
B181684

Attach the 4 claws to install the 2 assist grip plugs.


Hide 58574A 77.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672

a.

Attach the 6 clips to install the rear floor mat support plate.


Hide 67918E 78.INSTALL REAR DOOR SCUFF PLATE LH

B181674

a.

Attach the 3 claws and 4 clips to install the rear door scuff plate LH.


b.

Install the screw.


Hide 67917C 79.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 51775 80.INSTALL REAR STEP COVER

HINT:

Use the same procedure for both rear step covers.


a.
B181673

Attach the 2 claws to install the rear step cover.


Hide 67914B 81.INSTALL FRONT DOOR SCUFF PLATE LH

B448829

a.

Attach the 7 claws and 4 clips to install the front door scuff plate LH.


Hide 67913B 82.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 83.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)

Hide 84.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 85.INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)

Hide 86.INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 87.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).