Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the multiplex network master switch, power window regulator motor, harness or connector.


WIRING DIAGRAM

B449136E01
1.219,0.625 2.333,0.792 1.115,0.167 10 false FR DOOR LH*1 1.219,0.813 2.333,0.979 1.115,0.167 10 false FR DOOR RH*2 2.552,0.677 3.938,0.906 1.385,0.229 10 false from Main Body ECU 0.573,0.979 1.104,1.365 0.531,0.385 10 false from Battery 2.979,2.313 3.229,2.563 0.25,0.25 10 false 11 2.958,3.052 3.208,3.302 0.25,0.25 10 false 12 3.271,2.427 3.521,2.677 0.25,0.25 10 false B 3.271,3.125 3.656,3.375 0.385,0.25 10 false GND 3.99,2.115 4.25,2.313 0.26,0.198 10 false UP 3.75,2.813 4.271,3.01 0.521,0.198 10 false DOWN 4.323,1.99 4.573,2.24 0.25,0.25 10 false 20 4.313,2.688 4.563,2.938 0.25,0.25 10 false 15 5.281,1.99 5.531,2.24 0.25,0.25 10 false 10 5.354,2.688 5.604,2.938 0.25,0.25 10 false 7 5.344,0.917 5.594,1.167 0.25,0.25 10 false 2 5.333,1.271 5.583,1.521 0.25,0.25 10 false 1 5.604,1.021 5.854,1.271 0.25,0.25 10 false B 5.594,1.375 5.979,1.625 0.385,0.25 10 false GND 5.573,2.104 5.833,2.302 0.26,0.198 10 false UP 5.573,2.781 6.094,2.979 0.521,0.198 10 false DOWN 3.083,3.458 3.875,3.635 0.792,0.177 10 false I11*1, I22*2 5.146,3.458 5.938,3.635 0.792,0.177 10 false I12*1, I4*2 3.073,3.625 4.604,3.979 1.531,0.354 10 false Multiplex Network Master Switch Assembly 5.135,3.625 7.052,3.969 1.917,0.344 10 false Front Power Window Regulator Motor Assembly LH 0.719,4.396 1.417,4.583 0.698,0.188 10 false : LIN Line 0.292,4.125 1.063,4.323 0.771,0.198 10 false *2: for RHD 0.292,3.844 1.063,4.042 0.771,0.198 10 false *1: for LHD

PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK FOR DTC (B2312)

NG

2.CHECK FOR DTC (B2312)

OK

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MOTOR)

NG

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR MOTOR)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-

OK:

The display changes according to operation of the multiplex network master switch.


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U163952E02
1.188,2.354 1.208,2.667 false 1.302,2.344 1.708,2.677 false 0.073,0.094 2.427,0.448 2.354,0.354 10 false Front view of wire harness connector: (to Multiplex Network Master Switch) 0.406,2.083 0.677,2.281 0.271,0.198 10 false I22 0.406,1.74 0.656,1.927 0.25,0.188 10 false I11 1.188,2.698 1.333,2.885 0.146,0.188 10 false B 1.625,2.688 1.99,2.885 0.365,0.198 10 false GND 0.063,3.063 0.958,3.292 0.896,0.229 10 false *2: for RHD 0.063,2.75 0.979,2.969 0.917,0.219 10 false *1: for LHD 0.75,1.958 0.948,2.135 0.198,0.177 10 false *2 0.75,1.573 0.948,1.75 0.198,0.177 10 false *1

Disconnect the I11*1 or I22*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I11-11 (B) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
I22-11 (B) - Body ground Always 11 to 14 V


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I11-12 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
I22-12 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)
a.
U163953E01
0.068,0.042 2.705,0.415 2.637,0.372 10 Front view of wire harness connector: (to Front Power Window Regulator Motor) 0.653,1.56 0.871,1.710 0.218,0.150 10 I4 0.609,1.219 0.827,1.369 0.218,0.150 10 I12 2.398,2.069 2.552,2.268 0.154,0.200 10 B 0.635,2.035 0.986,2.234 0.352,0.200 10 GND 2.376,2.122 1.886,1.774 false 1.563,1.772 1.049,2.12 false 0.121,2.998 0.860,3.168 0.740,0.169 10 *2: for RHD 0.121,2.706 0.860,2.875 0.740,0.169 10 *1: for LHD 0.968,1.449 1.152,1.618 0.184,0.169 10 *2 0.968,1.108 1.152,1.277 0.184,0.169 10 *1

Disconnect the I12*1 or I4*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
I12-2 (B) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
I4-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I12-1 (GND) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
I4-1 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
a.
U164027E03
0.844,2.188 1.615,1.875 false 2.365,1.885 2.823,2.198 false 1.99,4.51 1.5,4.052 false 1.906,4.063 2.406,3.927 false 0.26,2.344 2.573,2.854 2.313,0.51 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor) 0.271,0.052 2.646,0.406 2.375,0.354 10 false Front view of wire harness connector: (to Multiplex Network Master Switch) 0.365,1.177 0.594,1.354 0.229,0.177 10 false I22 0.365,0.802 0.594,0.979 0.229,0.177 10 false I11 0.396,3.604 0.625,3.781 0.229,0.177 10 false I4 0.344,3.188 0.573,3.365 0.229,0.177 10 false I12 2.875,2.146 3.198,2.365 0.323,0.219 10 false UP 0.323,2.104 0.813,2.292 0.49,0.188 10 false DOWN 2.438,3.833 2.76,4.052 0.323,0.219 10 false UP 2.063,4.427 2.552,4.615 0.49,0.188 10 false DOWN 0.667,1.031 0.927,1.198 0.26,0.167 10 false *2 0.667,0.656 0.927,0.823 0.26,0.167 10 false *1 0.708,3.5 0.969,3.667 0.26,0.167 10 false *2 0.708,3.135 0.969,3.302 0.26,0.167 10 false *1 0.146,4.302 0.896,4.469 0.75,0.167 10 false *2: for RHD 0.146,3.969 0.875,4.135 0.729,0.167 10 false *1: for LHD

Disconnect the I11*1 or I22*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Disconnect the I12*1 or I4*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I11-20 (UP) - I12-10 (UP) Always Below 1 Ω
I11-15 (DOWN) - I12-7 (DOWN) Always Below 1 Ω
I11-20 (UP) or I12-10 (UP) - Body ground Always 10 kΩ or higher
I11-15 (DOWN) or I12-7 (DOWN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I22-20 (UP) - I4-10 (UP) Always Below 1 Ω
I22-15 (DOWN) - I4-7 (DOWN) Always Below 1 Ω
I22-20 (UP) or I4-10 (UP) - Body ground Always 10 kΩ or higher
I22-15 (DOWN) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

8.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
B175750E24
1.74,1.469 1.365,0.479 1.365,0.479 1.26,0.479 false 1.042,3.208 1.625,3.438 false 1.844,3.448 2.375,3.323 false 1.552,3.75 1.135,3.896 false 1.927,3.802 2.385,3.958 false 0.49,0.427 1.26,0.615 0.771,0.188 10 false Motor Gear 2,2.26 2.688,2.448 0.688,0.188 10 false Clockwise 0.875,3.073 1.24,3.26 0.365,0.188 10 false B 2.448,3.229 2.813,3.417 0.365,0.188 10 false GND 0.885,3.854 1.188,4.063 0.302,0.208 10 false UP 2.438,3.885 2.938,4.073 0.5,0.188 10 false DOWN 2.573,0.563 3.25,1.01 0.677,0.448 10 false Counter-clockwise


b.

Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.




c.

Apply negative (-) battery voltage to connector terminals 1 (GND), and 7 (DOWN) or 10 (UP).


d.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.


Motor gear rotates clockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.


Motor gear rotates counterclockwise (Down)




OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

8.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
B180611E01
1.754,1.46 1.38,0.468 1.38,0.468 1.274,0.468 false 0.362,0.359 1.138,0.543 0.776,0.184 10 Motor Gear 0.091,1.068 0.783,1.252 0.692,0.184 10 Clockwise 0.897,3.086 1.257,3.269 0.360,0.184 10 B 2.424,3.217 2.784,3.401 0.360,0.184 10 GND 0.798,3.882 1.158,4.066 0.360,0.184 10 UP 2.425,3.888 2.923,4.071 0.499,0.184 10 DOWN 1.052,3.205 1.627,3.428 false 1.876,3.445 2.398,3.316 false 1.578,3.746 1.157,3.892 false 1.937,3.737 2.392,3.895 false 0.562,2.3 1.756,2.508 1.194,0.208 10 Counterclockwise


b.

Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.


·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.




c.

Apply negative (-) battery voltage to the connector terminals 1 (GND), and 7 (DOWN) or 10 (UP).


d.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 10(UP).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 10(UP) within 1 second.


Motor gear rotates counterclockwise (Up)
1.

Connect the positive (+) battery cable to terminal 2(B), and connect the negative (-) battery cable to terminal 1(GND), and keep them connected for 3 seconds or more.

2.

With terminals 2(B) and 1(GND) connected, connect the negative (-) battery cable to terminal 7(DOWN).

3.

Disconnect and reconnect the negative (-) battery cable to terminal 7(DOWN) within 1 second.


Motor gear rotates clockwise (Down)




OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH