Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255725 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor consists of the motor, regulator and ECU. The power window regulator motor is driven by operating the power window switch.

This DTC is stored when the ECU built into the regulator motor determines that the power window switch is stuck.

HINT:

This DTC may be stored for all the windows.


NOTICE:
·

When the power window regulator motor is reinstalled or replaced, the power window control system must be initialized.

·

After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:

(a)

Close the power window by fully pulling up the power window switch and holding it in the auto up position.

(b)

Open the power window by fully pushing down the power window switch.




Multiplex Network Master Switch
DTC Code DTC Detection Condition Trouble Area
B2312
·

The multiplex network master switch is stuck.

·

The multiplex network master switch is held in the same position for more than 20 seconds.


·

Multiplex network master switch

·

Harness or connector

·

Multiplex network master switch held in same position for more than 20 seconds



Front Power Window Regulator Motor LH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The multiplex network master switch is stuck.

·

The multiplex network master switch is held in the same position for more than 20 seconds.


·

Multiplex network master switch

·

Power window regulator motor

·

Harness or connector

·

Multiplex network master switch held in same position for more than 20 seconds



Front Power Window Regulator Motor RH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator switch is stuck.

·

The power window regulator switch is held in same position for more than 20 seconds.


·

Power window regulator switch

·

Power window regulator motor

·

Harness or connector

·

Power window regulator switch held in same position for more than 20 seconds



Rear Power Window Regulator Motor LH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator switch is stuck.

·

The power window regulator switch is held in same position for more than 20 seconds.


·

Power window regulator switch

·

Power window regulator motor

·

Harness or connector

·

Power window regulator switch held in same position for more than 20 seconds



Rear Power Window Regulator Motor RH
DTC Code DTC Detection Condition Trouble Area
B2312
·

The power window regulator switch is stuck.

·

The power window regulator switch is held in same position for more than 20 seconds.


·

Power window regulator switch

·

Power window regulator motor

·

Harness or connector

·

Power window regulator switch held in same position for more than 20 seconds



WIRING DIAGRAM

B449026E01
0.156,0.073 1.438,0.385 1.281,0.313 12 false for Driver Side: 0.542,0.813 1.896,1.052 1.354,0.24 10 false from Main Body ECU 5.198,1.385 5.406,1.573 0.208,0.188 10 false 1 5.156,2.135 5.365,2.323 0.208,0.188 10 false 10 5.229,2.823 5.438,3.01 0.208,0.188 10 false 7 2.844,1.052 3.229,1.25 0.385,0.198 10 false GND 5.469,1.5 5.854,1.698 0.385,0.198 10 false GND 5.469,2.219 5.854,2.417 0.385,0.198 10 false UP 5.458,2.938 5.979,3.156 0.521,0.219 10 false DOWN 4.208,2.115 4.417,2.302 0.208,0.188 10 false 20 4.219,2.813 4.427,3 0.208,0.188 10 false 15 3.823,2.25 4.208,2.448 0.385,0.198 10 false UP 3.635,2.938 4.156,3.156 0.521,0.219 10 false DOWN 2.833,3.146 3.042,3.333 0.208,0.188 10 false 12 0.49,3.938 1.271,4.146 0.781,0.208 10 false *1: for LHD 0.49,4.198 1.271,4.406 0.781,0.208 10 false *2: for RHD 0.615,4.458 1.375,4.667 0.76,0.208 10 false : LIN Line 3,3.74 3.76,3.938 0.76,0.198 10 false I11*1, I22*2 2.979,3.938 4.51,4.323 1.531,0.385 10 false Multiplex Network Master Switch Assembly 5.094,3.719 5.854,3.917 0.76,0.198 10 false I12*1, I4*2 5.073,3.896 7.01,4.302 1.938,0.406 10 false Front Power Window Regulator Motor Assembly LH*1, RH*2

B449030E01
0.146,0.104 2.125,0.344 1.979,0.24 12 false for Front Passenger Side: 2.469,0.823 3.938,1.031 1.469,0.208 10 false from Main Body ECU 2.917,3.635 3.698,3.833 0.781,0.198 10 false I3*1, I25*2 5.229,1.375 5.385,1.573 0.156,0.198 10 false 1 5.177,2.125 5.333,2.323 0.156,0.198 10 false 10 5.25,2.583 5.406,2.781 0.156,0.198 10 false 7 5.229,3.063 5.385,3.26 0.156,0.198 10 false 4 5.479,1.51 5.938,1.708 0.458,0.198 10 false GND 5.49,2.229 5.948,2.427 0.458,0.198 10 false UP 5.51,2.688 5.969,2.885 0.458,0.198 10 false DOWN 5.49,3.156 5.948,3.354 0.458,0.198 10 false AUTO 3.719,3.156 4.177,3.354 0.458,0.198 10 false AUTO 3.656,2.708 4.115,2.906 0.458,0.198 10 false DOWN 3.875,2.25 4.333,2.448 0.458,0.198 10 false UP 4.24,2.594 4.396,2.792 0.156,0.198 10 false 7 4.229,2.156 4.385,2.354 0.156,0.198 10 false 6 4.24,3.042 4.396,3.24 0.156,0.198 10 false 8 3.177,3.281 3.635,3.479 0.458,0.198 10 false GND 0.51,3.979 1.25,4.167 0.74,0.188 10 false *1: for LHD 0.5,4.219 1.24,4.406 0.74,0.188 10 false *2: for RHD 0.625,4.469 1.365,4.656 0.74,0.188 10 false : LIN Line 2.917,3.146 3.073,3.344 0.156,0.198 10 false 1 2.927,3.802 4.5,4.167 1.573,0.365 10 false Power Window Regulator Switch Assembly 5.031,3.625 5.813,3.823 0.781,0.198 10 false I4*1, I12*2 5.021,3.802 6.938,4.146 1.917,0.344 10 false Front Power Window Regulator Motor Assembly RH*1, LH*2

B180279E02
2.384,0.776 3.733,0.956 1.349,0.180 10 from Main Body ECU 5.499,2.666 5.970,2.836 0.471,0.170 10 DOWN 3.667,2.666 4.129,2.836 0.461,0.170 10 DOWN 5.225,2.579 5.357,2.732 0.132,0.152 10 7 5.225,3.051 5.357,3.203 0.132,0.152 10 4 5.499,3.139 5.905,3.308 0.406,0.170 10 AUTO 5.499,2.225 5.780,2.395 0.281,0.170 10 UP 5.499,1.514 5.831,1.684 0.332,0.170 10 GND 0.67,4.264 1.652,4.434 0.982,0.170 10 : LIN Line 3.187,3.272 3.530,3.442 0.343,0.170 10 GND 3.715,3.139 4.135,3.309 0.420,0.170 10 AUTO 3.921,2.225 4.143,2.395 0.222,0.170 10 UP 4.255,2.134 4.351,2.287 0.097,0.152 10 6 4.255,2.572 4.351,2.724 0.097,0.152 10 7 4.255,3.027 4.351,3.179 0.097,0.152 10 8 2.986,3.157 3.083,3.309 0.097,0.152 10 1 3.079,3.622 3.322,3.775 0.242,0.152 10 J10 4.954,3.622 5.203,3.775 0.249,0.152 10 J11 5.186,2.119 5.394,2.271 0.208,0.152 10 10 5.241,1.4 5.344,1.552 0.103,0.152 10 1 3.077,3.806 4.412,4.337 1.335,0.531 10 Rear Power Window Regulator Switch Assembly LH 4.971,3.789 6.924,4.241 1.952,0.452 10 Rear Power Window Regulator Motor Assembly LH 0.147,0.05 1.893,0.380 1.746,0.329 12 for Rear LH Side:

B180279E03
2.385,0.776 3.733,0.956 1.349,0.180 10 from Main Body ECU 5.499,2.666 5.994,2.836 0.495,0.170 10 DOWN 3.667,2.666 4.129,2.836 0.461,0.170 10 DOWN 5.225,2.579 5.357,2.732 0.132,0.152 10 7 5.225,3.05 5.357,3.202 0.132,0.152 10 4 5.499,3.139 5.905,3.308 0.406,0.170 10 AUTO 5.499,2.225 5.780,2.395 0.281,0.170 10 UP 5.499,1.514 5.828,1.684 0.329,0.170 10 GND 0.67,4.264 1.652,4.434 0.982,0.170 10 : LIN Line 3.187,3.272 3.530,3.442 0.343,0.170 10 GND 3.715,3.139 4.135,3.309 0.420,0.170 10 AUTO 3.921,2.225 4.143,2.395 0.222,0.170 10 UP 4.255,2.134 4.362,2.287 0.107,0.152 10 6 4.255,2.577 4.362,2.729 0.107,0.152 10 7 4.255,3.04 4.362,3.192 0.107,0.152 10 8 2.97,3.175 3.078,3.328 0.107,0.152 10 1 3.01,3.63 3.184,3.782 0.174,0.152 10 J3 4.977,3.63 5.151,3.782 0.174,0.152 10 J4 5.186,2.119 5.394,2.271 0.208,0.152 10 10 5.249,1.404 5.359,1.557 0.110,0.152 10 1 3.029,3.812 4.397,4.345 1.368,0.533 10 Rear Power Window Regulator Switch Assembly RH 4.971,3.789 6.924,4.241 1.952,0.452 10 Rear Power Window Regulator Motor Assembly RH 0.131,0.068 2.031,0.499 1.900,0.431 12 for Rear RH Side:

PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DTC CHECK / CLEAR).

Result
Result Proceed to
B2312 is output. A
LIN communication DTCs are output. B
No DTCs output. C



A

3.CHECK MALFUNCTION LOCATION

B

C

END (DUE TO KEEPING SWITCH OPERATED FOR 20 SECONDS OR MORE)

3.CHECK MALFUNCTION LOCATION
a.

Check where DTC B2312 is output from.

Result
Result Proceed to
B2312 output from multiplex network master switch. A
B2312 output from driver side power window regulator motor. B
B2312 output from passenger side power window regulator motor. C
B2312 output from rear power window regulator motor LH. D
B2312 output from rear power window regulator motor RH. E



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

4.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR)

C

6.READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR)

D

9.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

E

12.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)
4.READ VALUE USING INTELLIGENT TESTER (DRIVER SIDE POWER WINDOW REGULATOR MOTOR)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF ON: Driver side power window auto up/down switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
OFF: Driver side power window switch not operated
-
D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
OFF: Driver side power window switch not operated
-

Result
Result Proceed to
The display does not change according to operation of the multiplex network master switch. A
The display changes according to operation of the multiplex network master switch (for LHD). B
The display changes according to operation of the multiplex network master switch (for RHD). C



A

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR AND BODY GROUND)
a.
U164027E02
0.844,2.198 1.615,1.885 false 2.385,1.875 2.844,2.188 false 2.021,4.5 1.531,4.042 false 1.906,4.052 2.406,3.917 false 0.333,2.313 2.698,2.823 2.365,0.51 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor) 0.208,0.073 2.583,0.427 2.375,0.354 10 false Front view of wire harness connector: (to Multiplex Network Master Switch) 0.344,1.177 0.573,1.354 0.229,0.177 10 false I22 0.333,0.781 0.563,0.958 0.229,0.177 10 false I11 0.396,3.583 0.625,3.76 0.229,0.177 10 false I4 0.365,3.208 0.594,3.385 0.229,0.177 10 false I12 2.896,2.156 3.219,2.375 0.323,0.219 10 false UP 0.365,2.146 0.854,2.333 0.49,0.188 10 false DOWN 2.448,3.823 2.771,4.042 0.323,0.219 10 false UP 2.094,4.438 2.583,4.625 0.49,0.188 10 false DOWN 0.667,1.01 0.927,1.177 0.26,0.167 10 false *2 0.667,0.646 0.927,0.813 0.26,0.167 10 false *1 0.708,3.479 0.969,3.646 0.26,0.167 10 false *2 0.708,3.094 0.969,3.26 0.26,0.167 10 false *1 0.146,4.302 0.896,4.469 0.75,0.167 10 false *2: for RHD 0.146,3.969 0.875,4.135 0.729,0.167 10 false *1: for LHD

Disconnect I11*1 or I22*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Disconnect I12*1 or I4*2 motor connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I11-20 (UP) - I12-10 (UP) Always Below 1 Ω
I11-15 (DOWN) - I12-7 (DOWN) Always Below 1 Ω
I11-20 (UP) or I12-10 (UP) - Body ground Always 10 kΩ or higher
I11-15 (DOWN) or I12-7 (DOWN) - Body ground Always 10 kΩ or higher


for RHD
Tester Connection Condition Specified Condition
I22-20 (UP) - I4-10 (UP) Always Below 1 Ω
I22-15 (DOWN) - I4-7 (DOWN) Always Below 1 Ω
I22-20 (UP) or I4-10 (UP) - Body ground Always 10 kΩ or higher
I22-15 (DOWN) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

6.READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto up/down signal / ON or OFF ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Up SW Front passenger side power window manual up signal / ON or OFF ON: Front passenger side power window manual up switch operated
OFF: Front passenger side power window regulator switch not operated
-
P Door P/W Down SW Front passenger side power window manual down signal / ON or OFF ON: Front passenger side power window manual down switch operated
OFF: Front passenger side power window regulator switch not operated
-

Result
Result Proceed to
The display does not change according to operation of the power window regulator switch. A
The display changes according to operation of the power window regulator switch (for LHD). B
The display changes according to operation of the power window regulator switch (for RHD). C



A

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

7.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
U164036E01
0.056,0.054 2.597,0.619 2.540,0.565 10 Component without harness connected: (Power Window Regulator Switch) 0.556,2.011 0.777,2.171 0.220,0.161 10 I25 0.614,1.67 0.749,1.830 0.134,0.161 10 I3 2.482,2.295 2.856,2.498 0.374,0.203 10 UP 2.448,1.985 2.822,2.189 0.374,0.203 10 GND 1.583,2.795 2.074,2.945 0.491,0.150 10 AUTO 2.066,2.588 2.557,2.748 0.491,0.160 10 DOWN 1.668,2.107 2.039,2.663 false 1.561,2.899 1.484,2.095 false 1.859,2.094 2.465,2.369 false 2.071,1.854 2.439,2.071 false 0.882,1.894 1.102,2.054 0.220,0.161 10 *2 0.88,1.553 1.062,1.713 0.182,0.161 10 *1 0.053,2.989 0.818,3.133 0.765,0.143 10 *2: for RHD 0.047,2.666 0.792,2.816 0.745,0.150 10 *1: for LHD

Remove the power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
I3-6 (UP) - I3-1 (GND) Manual up operation Below 1 Ω
I3-7 (DOWN) - I3-1 (GND) Manual down operation Below 1 Ω
I3-8 (AUTO) - I3-1 (GND) Auto up/down operation Below 1 Ω

for RHD
Tester Connection Switch Condition Specified Condition
I25-6 (UP) - I25-1 (GND) Manual up operation Below 1 Ω
I25-7 (DOWN) - I25-1 (GND) Manual down operation Below 1 Ω
I25-8 (AUTO) - I25-1 (GND) Auto up/down operation Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR)

NG

REPLACE FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR)
a.
U164021E02
1.104,1.958 1.604,1.823 false 1.844,1.823 2.323,1.438 false 2.01,1.833 2.427,1.656 false 2.115,4.188 1.646,3.708 false 1.896,3.833 2.271,3.656 false 1.844,4.51 1.531,3.896 false 0.156,2.135 2.74,2.5 2.583,0.365 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor) 0.198,0.083 2.615,0.417 2.417,0.333 10 false Front view of wire harness connector: (to Power Window Regulator Switch) 0.604,1.479 0.865,1.667 0.26,0.188 10 false I25 0.635,1.188 0.813,1.375 0.177,0.188 10 false I3 0.573,3.385 0.844,3.573 0.271,0.188 10 false I12 0.615,3.052 0.792,3.24 0.177,0.188 10 false I4 0.865,1.875 1.146,2.042 0.281,0.167 10 false UP 2.396,1.354 2.875,1.542 0.479,0.188 10 false DOWN 2.5,1.594 2.917,1.76 0.417,0.167 10 false AUTO 2.344,3.583 2.625,3.75 0.281,0.167 10 false UP 1.938,4.427 2.417,4.615 0.479,0.188 10 false DOWN 2.198,4.135 2.615,4.302 0.417,0.167 10 false AUTO 0.885,1.365 1.115,1.552 0.229,0.188 10 false *2 0.885,1.031 1.115,1.219 0.229,0.188 10 false *1 0.104,4.26 1.083,4.448 0.979,0.188 10 false *2: for RHD 0.104,3.938 1.083,4.125 0.979,0.188 10 false *1: for LHD 0.865,3.26 1.094,3.448 0.229,0.188 10 false *2 0.865,2.917 1.094,3.104 0.229,0.188 10 false *1

Disconnect the I3*1 or I25*2 switch connector.

HINT:
·

*1: for LHD

·

*2: for RHD




b.

Disconnect the I4*1 or I12*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
I3-6 (UP) - I4-10 (UP) Always Below 1 Ω
I3-7 (DOWN) - I4-7 (DOWN) Always Below 1 Ω
I3-8 (AUTO) - I4-4 (AUTO) Always Below 1 Ω
I3-6 (UP) or I4-10 (UP) - Body ground Always 10 kΩ or higher
I3-7 (DOWN) or I4-7 (DOWN) - Body ground Always 10 kΩ or higher
I3-8 (AUTO) or I4-4 (AUTO) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
I25-6 (UP) - I12-10 (UP) Always Below 1 Ω
I25-7 (DOWN) - I12-7 (DOWN) Always Below 1 Ω
I25-8 (AUTO) - I12-4 (AUTO) Always Below 1 Ω
I25-6 (UP) or I12-10 (UP) - Body ground Always 10 kΩ or higher
I25-7 (DOWN) or I12-7 (DOWN) - Body ground Always 10 kΩ or higher
I25-8 (AUTO) or I12-4 (AUTO) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

9.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear power window LH auto up/down signal / ON or OFF ON: Rear power window LH auto up/down switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Up SW Rear power window LH manual up signal / ON or OFF ON: Rear power window LH manual up switch operated
OFF: Rear power window LH switch not operated
-
RL Door P/W Down SW Rear power window LH manual down signal / ON or OFF ON: Rear power window LH manual down switch operated
OFF: The rear power window LH switch not operated
-

OK:

The display changes according to operation of the rear power window regulator switch.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

10.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
10.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
B184772E02
0.071,0.04 2.793,0.398 2.722,0.358 10 Component without harness connected: (Rear Power Window Regulator Switch LH) 2.415,2.112 2.789,2.315 0.374,0.203 10 UP 2.439,1.371 2.813,1.575 0.374,0.203 10 GND 0.518,2.225 1.009,2.428 0.491,0.203 10 AUTO 0.518,1.479 1.009,1.682 0.491,0.203 10 DOWN 1.084,1.577 1.616,1.973 false 1.02,2.321 1.429,2.034 false 1.845,2.031 2.386,2.19 false 2.093,1.782 2.431,1.457 false

a.

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J10-6 (UP) - J10-1 (GND) Manual up operation Below 1 Ω
J10-7 (DOWN) - J10-1 (GND) Manual down operation Below 1 Ω
J10-8 (AUTO) - J10-1 (GND) Auto up/down operation Below 1 Ω




OK

11.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MOTOR)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

11.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - POWER WINDOW REGULATOR MOTOR)
a.
U164016E02
1.135,1.49 1.604,1.677 false 1.854,1.719 2.333,1.323 false 2.01,1.729 2.448,1.594 false 1.198,3.646 1.573,3.844 false 1.917,3.99 2.281,3.813 false 1.052,4.229 1.469,4.052 false 0.167,2.156 2.646,2.531 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.156,0.031 2.708,0.406 2.552,0.375 10 false Front view of wire harness connector: (to Rear Power Window Regulator Switch) 0.594,1.104 0.844,1.292 0.25,0.188 10 false J10 0.667,3.24 0.906,3.427 0.24,0.188 10 false J11 0.875,1.396 1.156,1.563 0.281,0.167 10 false UP 2.396,1.24 2.875,1.385 0.479,0.146 10 false DOWN 2.469,1.531 2.885,1.698 0.417,0.167 10 false AUTO 2.344,3.719 2.625,3.885 0.281,0.167 10 false UP 0.531,4.198 1.01,4.385 0.479,0.188 10 false DOWN 0.719,3.521 1.135,3.688 0.417,0.167 10 false AUTO

Disconnect the J10 switch connector.


b.

Disconnect the J11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J10-6 (UP) - J11-10 (UP) Always Below 1 Ω
J10-7 (DOWN) - J11-7 (DOWN) Always Below 1 Ω
J10-8 (AUTO) - J11-4 (AUTO) Always Below 1 Ω
J10-6 (UP) or J11-10 (UP) - Body ground Always 10 kΩ or higher
J10-7 (DOWN) or J11-7 (DOWN) - Body ground Always 10 kΩ or higher
J10-8 (AUTO) or J11-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)
a.

Use the Data List to check if the power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows)>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear power window RH auto up/down signal / ON or OFF ON: The rear power window RH auto up/down switch operated
OFF: The rear power window RH switch not operated
-
RR Door P/W Up SW Rear power window RH manual up signal / ON or OFF ON: The rear power window RH manual up switch operated
OFF: The rear power window RH switch not operated
-
RR Door P/W Down SW Rear power window RH manual down signal / ON or OFF ON: The rear power window RH manual down switch operated
OFF: The rear power window RH switch not operated
-

OK:

The display changes according to operation of the rear power window regulator switch RH.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

13.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
13.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
B184772E03
0.069,0 2.773,0.358 2.704,0.358 10 Component without harness connected: (Rear Power Window Regulator Switch RH) 2.418,2.122 2.792,2.325 0.374,0.203 10 UP 2.431,1.29 2.805,1.493 0.374,0.203 10 GND 0.514,2.221 1.005,2.424 0.491,0.203 10 AUTO 0.514,1.514 1.005,1.717 0.491,0.203 10 DOWN 1.081,1.612 1.613,2.016 false 1.016,2.317 1.467,2.028 false 1.842,2.027 2.389,2.2 false 2.075,1.755 2.422,1.376 false

a.

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J3-6 (UP) - J3-1 (GND) Manual up operation Below 1 Ω
J3-7 (DOWN) - J3-1 (GND) Manual down operation Below 1 Ω
J3-8 (AUTO) - J3-1 (GND) Auto up/down operation Below 1 Ω




OK

14.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

14.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND)
U164020E02
1.135,1.531 1.604,1.719 false 1.854,1.74 2.333,1.344 false 2,1.823 2.427,1.646 false 1.219,3.635 1.594,3.833 false 1.906,3.969 2.281,3.792 false 1.042,4.24 1.458,4.063 false 0.188,2.115 2.667,2.49 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Motor) 0.156,0.031 2.635,0.406 2.479,0.375 10 false Front view of wire harness connector: (to Power Window Regulator Switch) 0.656,1.083 0.833,1.271 0.177,0.188 10 false J3 0.688,3.24 0.865,3.427 0.177,0.188 10 false J4 0.875,1.438 1.156,1.604 0.281,0.167 10 false UP 2.344,1.208 2.823,1.396 0.479,0.188 10 false DOWN 2.51,1.552 2.927,1.719 0.417,0.167 10 false AUTO 2.333,3.667 2.615,3.833 0.281,0.167 10 false UP 0.583,4.208 1.063,4.396 0.479,0.188 10 false DOWN 0.708,3.521 1.125,3.688 0.417,0.167 10 false AUTO

a.

Disconnect the J3 switch connector.


b.

Disconnect the J4 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J3-6 (UP) - J4-10 (UP) Always Below 1 Ω
J3-7 (DOWN) - J4-7 (DOWN) Always Below 1 Ω
J3-8 (AUTO) - J4-4 (AUTO) Always Below 1 Ω
J3-6 (UP) or J4-10 (UP) - Body ground Always 10 kΩ or higher
J3-7 (DOWN) or J4-7 (DOWN) - Body ground Always 10 kΩ or higher
J3-8 (AUTO) or J4-4 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR