If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, rear power window regulator motor RH, multiplex network master switch assembly, harness or connector.
Remove the rear power window regulator switch assembly RH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (U) - 3 (B) | UP | Below 1 Ω |
| 2 (SD) - 1 (D) | ||
| 5 (SU) - 4 (U) | OFF | Below 1 Ω |
| 2 (SD) - 1 (D) | ||
| 5 (SU) - 4 (U) | DOWN | Below 1 Ω |
| 3 (B) - 1 (D) |
OK
NG
Remove the rear power window regulator motor assembly RH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).
Apply battery voltage to the regulator motor and check the operation of the regulator motor.
| *1 | Motor Gear |
| *a | Clockwise |
| *b | Counterclockwise |
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1
Battery negative (-) → 2 |
Motor gear rotates clockwise |
| Battery positive (+) → 2
Battery negative (-) → 1 |
Motor gear rotates counterclockwise |
OK
NG
Disconnect the J21 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J21-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH) |
OK
NG
Disconnect the J21 rear power window regulator switch assembly RH connector.
Disconnect the J20 rear power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J21-4 (U) - J20-1 | Always | Below 1 Ω |
| J21-1 (D) - J20-2 | Always | Below 1 Ω |
| J21-4 (U) or J20-1 - Body ground | Always | 10 KΩ or higher |
| J21-1 (D) or J20-2 - Body ground | Always | 10 KΩ or higher |
OK
NG
Disconnect the J21 rear power window regulator switch assembly RH connector.
Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J21-5 (SU) - I31-10 (U) | Always | Below 1 Ω |
| J21-2 (SD) - I31-18 (D) | Always | Below 1 Ω |
| J21-5 (SU) or I30-10 (U) - Body ground | Always | 10 kΩ or higher |
| J21-2 (SD) or I30-18 (D) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J21-5 (SU) - I26-16 (U) | Always | Below 1 Ω |
| J21-2 (SD) - I26-15 (D) | Always | Below 1 Ω |
| J21-5 (SU) or I26-16 (U) - Body ground | Always | 10 kΩ or higher |
| J21-2 (SD) or I26-15 (D) - Body ground | Always | 10 kΩ or higher |
OK
NG