Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255735 POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only)  Rear Power Window LH does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, power window rear regulator motor LH, multiplex network master switch assembly, harness or connector.


WIRING DIAGRAM

B292714E02
0.11,2.024 1.105,2.372 0.995,0.348 10 from P/W MAIN Relay 0.04,4.124 0.783,4.282 0.743,0.157 10 *1: for LHD 2.548,3.923 3.358,4.080 0.810,0.157 10 J23 2.563,1.909 2.658,2.067 0.095,0.157 10 3 2.714,2.013 3.523,2.171 0.810,0.157 10 B 2.548,4.089 4.480,4.429 1.932,0.340 10 Rear Power Window Regulator Switch Assembly LH 5.438,3.923 6.248,4.080 0.810,0.157 10 I31*1, I26*2 5.438,4.089 7.053,4.429 1.615,0.340 10 Multiplex Network Master Switch Assembly 5.15,1.613 5.959,1.771 0.810,0.157 10 J22 5.15,1.78 7.138,2.120 1.988,0.340 10 Rear Power Window Regulator Motor Assembly LH 0.04,4.458 0.783,4.615 0.743,0.157 10 *2: for RHD 3.924,1.132 4.051,1.289 0.127,0.157 10 D 3.83,2.804 4.051,2.961 0.220,0.157 10 SU 3.83,3.43 4.051,3.587 0.220,0.157 10 SD 3.924,0.506 4.051,0.663 0.127,0.157 10 U 4.105,1.018 4.394,1.175 0.288,0.157 10 1 4.105,2.69 4.394,2.847 0.288,0.157 10 5 4.105,3.316 4.394,3.473 0.288,0.157 10 2 4.105,0.392 4.394,0.549 0.288,0.157 10 4 5.874,2.804 6.162,2.961 0.288,0.157 10 U 5.874,3.43 6.162,3.587 0.288,0.157 10 D 5.705,1.038 5.814,1.195 0.109,0.157 10 2 5.117,2.71 5.808,2.868 0.691,0.157 10 12*1, 18*2 5.117,3.336 5.808,3.493 0.691,0.157 10 13*1, 10*2 5.705,0.412 5.814,0.569 0.109,0.157 10 1

PROCEDURE

1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.
B107881E07
1.197,1.866 1.316,2.011 0.119,0.145 10 U 2.599,2.259 2.720,2.401 0.121,0.142 10 D 1.879,1.866 1.991,2.015 0.113,0.149 10 B 2.249,1.866 2.460,2.010 0.211,0.144 10 SD 0.714,2.259 0.924,2.406 0.210,0.147 10 SU 1.549,2.786 1.398,1.943 1.398,1.943 1.341,1.943 false 1.333,2.797 1.063,2.336 1.063,2.336 0.981,2.336 false 2.02,2.786 2.171,1.943 2.171,1.943 2.228,1.943 false 2.236,2.797 2.506,2.336 2.506,2.336 2.588,2.336 false 1.777,2.786 1.812,1.943 1.812,1.943 1.86,1.943 false

Remove the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (U) - 3 (B) UP Below 1 Ω
2 (SD) - 1 (D)
5 (SU) - 4 (U) OFF Below 1 Ω
2 (SD) - 1 (D)
5 (SU) - 4 (U) DOWN Below 1 Ω
3 (B) - 1 (D)




OK

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B171738E15
0.321,1.811 0.517,1.987 0.195,0.176 10 *a 0.73,2.662 0.945,2.838 0.215,0.176 10 *b 1.853,0.467 2.029,0.642 0.176,0.176 10 *1 1.544,2.091 1.544,0.565 1.544,0.565 1.807,0.565 false

Remove the rear window regulator motor assembly LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).


b.

Apply battery voltage to the motor connector according to the table below.

Text in Illustration
*1 Motor Gear
*a Counterclockwise
*b Clockwise

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates counterclockwise




OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BATTERY)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BATTERY)
a.
U164191E01
0.083,0.063 0.253,0.224 0.170,0.161 10 *a 0.232,1.123 0.485,1.305 0.253,0.181 10 J23 1.786,1.607 1.899,1.752 0.113,0.145 10 B 1.749,1.294 1.845,1.584 false

Disconnect the J23 rear power window regulator switch assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J23-3 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly LH)



OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
a.

Disconnect the J23 rear power window regulator switch assembly LH connector.


b.

Disconnect the J22 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J23-4 (U) - J22-1 Always Below 1 Ω
J23-1 (D) - J22-2 Always Below 1 Ω
J23-4 (U) or J22-1 - Body ground Always 10 KΩ or higher
J23-1 (D) or J22-2 - Body ground Always 10 KΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - MULTIPLEX NETWORK MASTER SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - MULTIPLEX NETWORK MASTER SWITCH)
a.

Disconnect the J23 rear power window regulator switch assembly LH connector.


b.

Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
J23-5 (SU) - I31-12 (U) Always Below 1 Ω
J23-2 (SD) - I31-13 (D) Always Below 1 Ω
J23-5 (SU) or I30-12 (U) - Body ground Always 10 kΩ or higher
J23-2 (SD) or I30-13 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
J23-5 (SU) - I26-18 (U) Always Below 1 Ω
J23-2 (SD) - I26-10 (D) Always Below 1 Ω
J23-5 (SU) or I26-18 (U) - Body ground Always 10 kΩ or higher
J23-2 (SD) or I26-10 (D) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR