Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255742 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof ECU Power Source Circuit  


DESCRIPTION

If the sliding function and tilt function do not operate, there may be a malfunction in the sliding roof ECU power source circuit.

WIRING DIAGRAM

B156647E02
5.417,3.375 6.304,3.522 0.887,0.147 10 R5 5.678,1.9 6.566,2.046 0.887,0.147 10 E 5.43,1.763 5.572,1.910 0.142,0.147 10 2 5.678,1.238 6.566,1.384 0.887,0.147 10 IG 5.43,1.101 5.572,1.248 0.142,0.147 10 5 5.678,0.576 6.566,0.722 0.887,0.147 10 B 2.995,0.726 3.883,0.873 0.887,0.147 10 S/ROOF 0.679,0.552 1.566,0.699 0.887,0.147 10 from Battery 0.126,1.211 1.535,1.358 1.409,0.147 10 from IG1 NO. 3 Relay 2.836,1.413 3.770,1.559 0.934,0.147 10 ECU-IG No. 2 5.43,0.439 5.572,0.586 0.142,0.147 10 1 5.417,3.539 6.948,3.848 1.531,0.309 10 Sliding Roof Drive Gear (Sliding Roof ECU)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IGNITION SWITCH SIGNAL)
a.

Use the Data List to check if the ignition switch signal is functioning properly (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).


Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Ignition (MPX) Ignition switch signal (MPX signal)/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
Ignition (Direct Signal) Ignition switch signal/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

The intelligent tester displays as shown in the table according to the operation of each switch.



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

2.INSPECT FUSE (S/ROOF, ECU-IG NO. 2)
2.INSPECT FUSE (S/ROOF, ECU-IG NO. 2)
a.

Remove the S/ROOF and ECU-IG NO. 2 fuses from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S/ROOF fuse Always Below 1 Ω
ECU-IG NO. 2 fuse Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)
a.
U163858E01
1.609,1.085 1.825,1.251 0.216,0.166 10 R5 0.2,1.898 0.332,2.064 0.132,0.166 10 B 1.652,2.9 1.787,3.073 0.135,0.172 10 E 0.974,2.9 1.159,3.054 0.185,0.154 10 IG 1.078,2.408 1.081,2.862 false 1.409,2.062 1.65,2.877 false 0.033,0.001 2.762,0.499 2.729,0.498 10 Front view of wire harness connector: (to Sliding Roof Drive Gear) 1.019,2 0.372,2 false

Disconnect the R5 drive gear connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-2 (E) - Body ground Always Below 1 Ω

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R5-1 (B) - Body ground Always 11 to 14 V
R5-5 (IG) - Body ground Engine switch off Below 1 V
R5-5 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR