Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255742 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof ECU Power Source Circuit  


DESCRIPTION

If the sliding function and tilt function do not operate, there may be a malfunction in the sliding roof drive gear sub-assembly (sliding roof ECU) power source circuit.

WIRING DIAGRAM

B156647E16
5.073,3.375 5.958,3.521 0.885,0.146 10 false R15 5.677,1.823 6.563,1.969 0.885,0.146 10 false E 5.354,1.688 5.563,1.833 0.208,0.146 10 false 12 5.688,1.198 6.573,1.344 0.885,0.146 10 false IG 5.417,1.042 5.563,1.188 0.146,0.146 10 false 1 5.677,0.521 6.563,0.667 0.885,0.146 10 false B 3.01,0.74 3.896,0.885 0.885,0.146 10 false S/ROOF 0.646,0.563 1.531,0.708 0.885,0.146 10 false from Battery 0.135,1.25 1.542,1.396 1.406,0.146 10 false from IG1 NO.1 Relay 2.813,1.385 3.75,1.531 0.938,0.146 10 false ECU-IG NO.2 5.406,0.365 5.573,0.583 0.167,0.219 10 false 8 5.052,3.552 7.031,4.104 1.979,0.552 10 false Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IGNITION SWITCH SIGNAL)
a.

Use the Data List to check if the ignition switch signal is functioning properly (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).


Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Ignition (MPX) Ignition switch signal (MPX signal)/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-
Ignition (Direct Signal) Ignition switch signal/ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

The intelligent tester displays as shown in the table according to the operation of each switch.



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) - BATTERY AND BODY GROUND)
a.
U155876E01
0.072,0.031 0.223,0.182 0.151,0.151 10 *a 1.568,0.318 1.871,0.464 0.304,0.147 10 R15 2.707,1.609 2.818,1.758 0.111,0.149 10 E 1.256,1.382 1.027,1.703 1.027,1.703 0.794,1.703 false 1.256,1.133 1.027,0.816 1.027,0.816 0.794,0.816 false 2.182,1.382 2.412,1.703 2.412,1.703 2.645,1.703 false 0.64,1.609 0.751,1.758 0.111,0.149 10 B 0.566,0.738 0.749,0.887 0.182,0.149 10 IG

Disconnect the R15 sliding roof drive gear sub-assembly (sliding roof ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU))


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-12 (E) - Body ground Always Below 1 Ω

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R15-8 (B) - Body ground Always 11 to 14 V
R15-1 (IG) - Body ground Engine switch off Below 1 V
R15-1 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR