Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255742 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE OPEN or TILT UP switch in the map light is stuck for 30 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2342 Sliding roof drive gear (sliding roof ECU) detects sliding roof switch in map light is stuck for 30 seconds or more
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof switch)

·

Harness or connector



WIRING DIAGRAM

B181150E01
5.385,4.147 5.759,4.293 0.373,0.147 10 R5 1.419,0.579 1.792,0.726 0.373,0.147 10 7 1.463,1.057 1.836,1.203 0.373,0.147 10 8 1.419,1.519 1.792,1.666 0.373,0.147 10 18 1.419,1.991 1.792,2.137 0.373,0.147 10 19 1.419,2.473 1.792,2.620 0.373,0.147 10 17 5.684,0.747 6.058,0.893 0.373,0.147 10 CLS 5.684,1.212 6.058,1.359 0.373,0.147 10 OPN 5.684,1.674 6.216,1.821 0.531,0.147 10 DWN 5.684,2.168 6.058,2.314 0.373,0.147 10 UP 5.684,2.639 6.058,2.786 0.373,0.147 10 E 5.356,0.616 5.485,0.763 0.129,0.147 10 9 5.356,1.082 5.485,1.228 0.129,0.147 10 7 5.356,1.543 5.485,1.690 0.129,0.147 10 8 5.317,2.037 5.543,2.183 0.226,0.147 10 10 5.356,2.509 5.485,2.655 0.129,0.147 10 2 0.818,0.747 1.192,0.893 0.373,0.147 10 CLS 0.818,1.212 1.192,1.359 0.373,0.147 10 OPN 0.818,1.674 1.349,1.821 0.531,0.147 10 DOWN 0.818,2.168 1.192,2.314 0.373,0.147 10 UP 0.818,2.639 1.270,2.786 0.451,0.147 10 GND9 5.385,4.302 6.958,4.615 1.573,0.313 10 Sliding Roof Drive Gear (Sliding Roof ECU) 0.435,3.588 1.820,3.901 1.385,0.313 10 Map Light Assembly (Sliding Roof Switch) 0.435,3.432 0.774,3.635 0.339,0.203 10 R7

PROCEDURE

1.CHECK FOR DTC

b.

Check the DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2342 is output A
No DTC is output B



A

2.READ VALUE USING INTELLIGENT TESTER (SWITCH STATUS)

B

2.READ VALUE USING INTELLIGENT TESTER (SWITCH STATUS)
a.

Use the Data List to check if the sliding roof switch is functioning properly (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Down Switch Failure(Current) Down switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt down signal failure (Current)
Not Fail: Sliding roof tilt down signal not fail (Current)
-
Up Switch Failure(Current) Up switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof tilt up signal failure (Current)
Not Fail: Sliding roof tilt up signal not fail (Current)
-
Close Switch Failure(Current) Close switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof close signal failure (Current)
Not Fail: Sliding roof close signal not fail (Current)
-
Open Switch Failure(Current) Open switch failure signal (Current)/Fail or Not Fail Fail: Sliding roof open signal failure (Current)
Not Fail: Sliding roof open signal not fail (Current)
-
Down Switch Failure(Past) Down switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt down signal failure (Past)
Not Fail: Sliding roof tilt down signal not fail (Past)
-
Up Switch Failure(Past) Up switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof tilt up signal failure (Past)
Not Fail: Sliding roof tilt up signal not fail (Past)
-
Close Switch Failure(Past) Close switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof close signal failure (Past)
Not Fail: Sliding roof close signal not fail (Past)
-
Open Switch Failure(Past) Open switch failure signal (Past)/Fail or Not Fail Fail: Sliding roof open signal failure (Past)
Not Fail: Sliding roof open signal not fail (Past)
-


OK:

"Not Fail" appears on screen.



OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
3.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
B237546E01
0.154,0.131 2.673,0.482 2.519,0.350 10 Component without harness connected: (Map Light Assembly) 1.12,1.098 1.468,1.245 0.348,0.147 10 OPN 2.355,1.098 2.703,1.245 0.348,0.147 10 CLS 1.535,2.866 1.756,3.013 0.221,0.147 10 UP 1.976,2.866 2.481,3.013 0.505,0.147 10 DOWN 2.698,2.866 3.120,3.013 0.422,0.147 10 GND9 2.768,2.232 2.903,2.866 false 2.238,2.866 2.632,2.237 false 1.652,2.866 2.483,2.242 false 1.93,1.984 2.32,1.183 false 1.793,1.984 1.53,1.183 false


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
19 (UP) - 17 (GND9) UP switch is pressed Below 1 Ω
19 (UP) - 17 (GND9) UP switch is not pressed 10 kΩ or higher
18 (DOWN) - 17 (GND9) DOWN switch is pressed Below 1 Ω
18 (DOWN) - 17 (GND9) DOWN switch is not pressed 10 kΩ or higher
8 (OPN) - 17 (GND9) OPEN switch is pressed Below 1 Ω
8 (OPN) - 17 (GND9) OPEN switch is not pressed 10 kΩ or higher
7 (CLS) - 17 (GND9) CLOSE switch is pressed Below 1 Ω
7 (CLS) - 17 (GND9) CLOSE switch is not pressed 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
B449952E01
0.365,1.333 0.667,1.552 0.302,0.219 3.74,1.333 4.042,1.552 0.302,0.219 0.573,2.052 1.333,1.375 true 1.135,2.042 1.531,1.583 true 1.656,2.063 1.719,1.604 true 2.292,2.021 1.896,1.604 true 2.74,1.99 2.094,1.583 true 4.417,1.552 3.958,2.01 true 4.563,1.552 4.563,2.021 true 4.656,1.563 5.083,2 true 5.083,1.427 5.667,1.938 true 5.219,1.438 6.177,1.958 true 0.531,0.302 2.875,0.719 2.344,0.417 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear) 0.438,1.354 0.729,1.583 0.292,0.229 10 false R5 0.406,2.083 0.625,2.302 0.219,0.219 10 false E 3.802,1.344 4.094,1.573 0.292,0.229 10 false R7 4.333,0.25 6.656,0.792 2.323,0.542 10 false Front view of wire harness connector: (to Map Light Assembly) 0.927,2.083 1.302,2.313 0.375,0.229 10 false OPN 1.458,2.073 1.885,2.292 0.427,0.219 10 false DWN 2.167,2.052 2.531,2.281 0.365,0.229 10 false CLS 2.76,2.042 3.042,2.271 0.281,0.229 10 false UP 3.771,2.063 4.24,2.281 0.469,0.219 10 false GND9 4.375,2.073 4.875,2.292 0.5,0.219 10 false DOWN 5.063,2.042 5.458,2.26 0.396,0.219 10 false UP 5.583,2.031 6,2.26 0.417,0.229 10 false CLS 6.198,2.031 6.531,2.26 0.333,0.229 10 false UP

a.

Disconnect the R5 drive gear connector.


b.

Disconnect the R7 map light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (UP) - R7-19 (UP) Always Below 1 Ω
R5-8 (DWN) - R7-18 (DOWN) Always Below 1 Ω
R5-7 (OPN) - R7-8 (OPN) Always Below 1 Ω
R5-9 (CLS) - R7-7 (CLS) Always Below 1 Ω
R7-17 (GND9) - Body ground Always Below 1 Ω
R5-2 (E) - Body ground Always Below 1 Ω
R5-10 (UP) or R7-19 (UP) - Body ground Always 10 kΩ or higher
R5-8 (DWN) or R7-18 (DOWN) - Body ground Always 10 kΩ or higher
R5-7 (OPN) or R7-8 (OPN) - Body ground Always 10 kΩ or higher
R5-9 (CLS) or R7-7 (CLS) - Body ground Always 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR