Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255742 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2343  Position Initialization Incomplete  


DESCRIPTION

This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.

DTC Code DTC Detection Condition Trouble Area
B2343 The sliding roof drive gear (sliding roof ECU) has not been initialized
·

Sliding roof drive gear sub-assembly (Sliding roof ECU)

·

Map light assembly (Sliding roof switch)

·

Harness or connector



WIRING DIAGRAM

B181150E01
5.385,4.147 5.759,4.293 0.373,0.147 10 R5 1.419,0.579 1.792,0.726 0.373,0.147 10 7 1.463,1.057 1.836,1.203 0.373,0.147 10 8 1.419,1.519 1.792,1.666 0.373,0.147 10 18 1.419,1.991 1.792,2.137 0.373,0.147 10 19 1.419,2.473 1.792,2.620 0.373,0.147 10 17 5.684,0.747 6.058,0.893 0.373,0.147 10 CLS 5.684,1.212 6.058,1.359 0.373,0.147 10 OPN 5.684,1.674 6.216,1.821 0.531,0.147 10 DWN 5.684,2.168 6.058,2.314 0.373,0.147 10 UP 5.684,2.639 6.058,2.786 0.373,0.147 10 E 5.356,0.616 5.485,0.763 0.129,0.147 10 9 5.356,1.082 5.485,1.228 0.129,0.147 10 7 5.356,1.543 5.485,1.690 0.129,0.147 10 8 5.317,2.037 5.543,2.183 0.226,0.147 10 10 5.356,2.509 5.485,2.655 0.129,0.147 10 2 0.818,0.747 1.192,0.893 0.373,0.147 10 CLS 0.818,1.212 1.192,1.359 0.373,0.147 10 OPN 0.818,1.674 1.349,1.821 0.531,0.147 10 DOWN 0.818,2.168 1.192,2.314 0.373,0.147 10 UP 0.818,2.639 1.270,2.786 0.451,0.147 10 GND9 5.385,4.302 6.958,4.615 1.573,0.313 10 Sliding Roof Drive Gear (Sliding Roof ECU) 0.435,3.588 1.820,3.901 1.385,0.313 10 Map Light Assembly (Sliding Roof Switch) 0.435,3.432 0.774,3.635 0.339,0.203 10 R7

PROCEDURE

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Check that the sliding roof drive gear can be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

OK:

Sliding roof drive gear can be initialized.




OK

2.CHECK FOR DTC

NG

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
2.CHECK FOR DTC

b.

Check the DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC B2343 is output B



A

END

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
B449952E01
0.365,1.333 0.667,1.552 0.302,0.219 3.74,1.333 4.042,1.552 0.302,0.219 0.573,2.052 1.333,1.375 true 1.135,2.042 1.531,1.583 true 1.656,2.063 1.719,1.604 true 2.292,2.021 1.896,1.604 true 2.74,1.99 2.094,1.583 true 4.417,1.552 3.958,2.01 true 4.563,1.552 4.563,2.021 true 4.656,1.563 5.083,2 true 5.083,1.427 5.667,1.938 true 5.219,1.438 6.177,1.958 true 0.531,0.302 2.875,0.719 2.344,0.417 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear) 0.438,1.354 0.729,1.583 0.292,0.229 10 false R5 0.406,2.083 0.625,2.302 0.219,0.219 10 false E 3.802,1.344 4.094,1.573 0.292,0.229 10 false R7 4.333,0.25 6.656,0.792 2.323,0.542 10 false Front view of wire harness connector: (to Map Light Assembly) 0.927,2.083 1.302,2.313 0.375,0.229 10 false OPN 1.458,2.073 1.885,2.292 0.427,0.219 10 false DWN 2.167,2.052 2.531,2.281 0.365,0.229 10 false CLS 2.76,2.042 3.042,2.271 0.281,0.229 10 false UP 3.771,2.063 4.24,2.281 0.469,0.219 10 false GND9 4.375,2.073 4.875,2.292 0.5,0.219 10 false DOWN 5.063,2.042 5.458,2.26 0.396,0.219 10 false UP 5.583,2.031 6,2.26 0.417,0.229 10 false CLS 6.198,2.031 6.531,2.26 0.333,0.229 10 false UP

a.

Disconnect the R5 drive gear connector.


b.

Disconnect the R7 map light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-10 (UP) - R7-19 (UP) Always Below 1 Ω
R5-8 (DWN) - R7-18 (DOWN) Always Below 1 Ω
R5-7 (OPN) - R7-8 (OPN) Always Below 1 Ω
R5-9 (CLS) - R7-7 (CLS) Always Below 1 Ω
R7-17 (GND9) - Body ground Always Below 1 Ω
R5-2 (E) - Body ground Always Below 1 Ω
R5-10 (UP) or R7-19 (UP) - Body ground Always 10 kΩ or higher
R5-8 (DWN) or R7-18 (DOWN) - Body ground Always 10 kΩ or higher
R5-7 (OPN) or R7-8 (OPN) - Body ground Always 10 kΩ or higher
R5-9 (CLS) or R7-7 (CLS) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
B237546E01
0.154,0.131 2.673,0.482 2.519,0.350 10 Component without harness connected: (Map Light Assembly) 1.12,1.098 1.468,1.245 0.348,0.147 10 OPN 2.355,1.098 2.703,1.245 0.348,0.147 10 CLS 1.535,2.866 1.756,3.013 0.221,0.147 10 UP 1.976,2.866 2.481,3.013 0.505,0.147 10 DOWN 2.698,2.866 3.120,3.013 0.422,0.147 10 GND9 2.768,2.232 2.903,2.866 false 2.238,2.866 2.632,2.237 false 1.652,2.866 2.483,2.242 false 1.93,1.984 2.32,1.183 false 1.793,1.984 1.53,1.183 false


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
19 (UP) - 17 (GND9) UP switch is pressed Below 1 Ω
19 (UP) - 17 (GND9) UP switch is not pressed 10 kΩ or higher
18 (DOWN) - 17 (GND9) DOWN switch is pressed Below 1 Ω
18 (DOWN) - 17 (GND9) DOWN switch is not pressed 10 kΩ or higher
8 (OPN) - 17 (GND9) OPEN switch is pressed Below 1 Ω
8 (OPN) - 17 (GND9) OPEN switch is not pressed 10 kΩ or higher
7 (CLS) - 17 (GND9) CLOSE switch is pressed Below 1 Ω
7 (CLS) - 17 (GND9) CLOSE switch is not pressed 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)