Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052851 SLIDING ROOF / CONVERTIBLE _0255742 SLIDING ROOF SYSTEM C

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  B2343  Position Initialization Incomplete  


DESCRIPTION

This DTC is output when the sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized.

DTC Code DTC Detection Condition Trouble Area
B2343 The sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized
·

Sliding roof drive gear sub-assembly (sliding roof ECU)

·

Map light assembly (sliding roof switch)

·

Harness or connector



WIRING DIAGRAM

B181150E04
5.146,4.021 5.521,4.167 0.375,0.146 10 false R15 1.417,0.448 1.792,0.594 0.375,0.146 10 false 7 1.458,0.927 1.833,1.073 0.375,0.146 10 false 8 1.417,1.385 1.792,1.531 0.375,0.146 10 false 18 1.417,1.865 1.792,2.01 0.375,0.146 10 false 19 1.417,2.344 1.792,2.49 0.375,0.146 10 false 17 5.688,0.677 6.063,0.823 0.375,0.146 10 false CLS 5.688,1.167 6.063,1.313 0.375,0.146 10 false OPN 5.677,1.635 6.208,1.781 0.531,0.146 10 false DWN 5.688,2.083 6.063,2.229 0.375,0.146 10 false UP 5.688,2.594 6.063,2.74 0.375,0.146 10 false E 5.354,0.49 5.479,0.635 0.125,0.146 10 false 5 5.354,0.948 5.479,1.094 0.125,0.146 10 false 7 5.354,1.417 5.479,1.563 0.125,0.146 10 false 6 5.354,1.906 5.583,2.052 0.229,0.146 10 false 4 5.292,2.375 5.49,2.521 0.198,0.146 10 false 12 0.979,0.698 1.281,0.844 0.302,0.146 10 false CLS 0.927,1.177 1.281,1.323 0.354,0.146 10 false OPN 0.792,1.667 1.271,1.813 0.479,0.146 10 false DOWN 1.031,2.125 1.271,2.271 0.24,0.146 10 false UP 0.844,2.604 1.271,2.75 0.427,0.146 10 false GND9 5.146,4.177 7.135,4.615 1.99,0.438 10 false Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU) 0.438,3.625 1.823,3.938 1.385,0.313 10 false Map Light Assembly (Sliding Roof Switch) 0.438,3.438 0.781,3.635 0.344,0.198 10 false R7

PROCEDURE

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Check that the sliding roof drive gear sub-assembly can be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).

OK:

Sliding roof drive gear can be initialized.




OK

2.CHECK FOR DTC

NG

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) AND BODY GROUND)
2.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC B2343 is output B



A

END

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY - MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) AND BODY GROUND)
a.

Disconnect the R15 sliding roof drive gear sub-assembly (sliding roof ECU) connector.


b.

Disconnect the R7 map light assembly (sliding roof switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-4 (UP) - R7-19 (UP) Always Below 1 Ω
R15-6 (DWN) - R7-18 (DOWN) Always Below 1 Ω
R15-7 (OPN) - R7-8 (OPN) Always Below 1 Ω
R15-5 (CLS) - R7-7 (CLS) Always Below 1 Ω
R7-17 (GND9) - Body ground Always Below 1 Ω
R15-12 (E) - Body ground Always Below 1 Ω
R15-4 (UP) or R7-19 (UP) - Body ground Always 10 kΩ or higher
R15-6 (DWN) or R7-18 (DOWN) - Body ground Always 10 kΩ or higher
R15-7 (OPN) or R7-8 (OPN) - Body ground Always 10 kΩ or higher
R15-5 (CLS) or R7-7 (CLS) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
a.
B237546E02
0.154,0.131 2.673,0.482 2.519,0.350 10 *a 0.83,1.098 1.178,1.245 0.348,0.147 10 OPN 2.506,1.098 2.854,1.245 0.348,0.147 10 CLS 1.428,2.701 1.650,2.847 0.221,0.147 10 UP 1.561,2.919 2.066,3.065 0.505,0.147 10 DOWN 2.546,2.768 2.968,2.914 0.422,0.147 10 GND9 2.768,2.27 2.768,2.768 false 2.496,2.27 1.984,2.781 1.984,2.781 1.713,2.781 false 2.629,2.27 2.397,3.009 2.397,3.009 2.127,3.009 false 1.93,1.95 2.193,1.183 2.193,1.183 2.464,1.183 false 1.795,1.95 1.532,1.183 1.532,1.183 1.262,1.183 false

Remove the map light assembly (sliding roof switch) (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).

Text in Illustration
*a Component with harness connected
(Map Light Assembly (Sliding Roof Switch))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
19 (UP) - 17 (GND9) UP switch is pressed Below 1 Ω
19 (UP) - 17 (GND9) UP switch is not pressed 10 kΩ or higher
18 (DOWN) - 17 (GND9) DOWN switch is pressed Below 1 Ω
18 (DOWN) - 17 (GND9) DOWN switch is not pressed 10 kΩ or higher
8 (OPN) - 17 (GND9) OPEN switch is pressed Below 1 Ω
8 (OPN) - 17 (GND9) OPEN switch is not pressed 10 kΩ or higher
7 (CLS) - 17 (GND9) CLOSE switch is pressed Below 1 Ω
7 (CLS) - 17 (GND9) CLOSE switch is not pressed 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)