Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255761 POWER BACK DOOR SYSTEM J

DOOR / HATCH  POWER BACK DOOR SYSTEM  Back Door Lock Motor Circuit  


DESCRIPTION

The back door lock motor is built into the back door lock assembly. The power back door unit assembly (power back door ECU) controls the back door lock motor to open/close the back door. This power back door unit assembly (power back door ECU) applies current to terminals 2 and 1 to operate the motor to close the door. It reverses the direction of the current to operate the motor to open the door.

WIRING DIAGRAM

B312267E06
5.115,2.75 5.469,2.896 0.354,0.146 10 false L52 5.104,2.927 7.146,3.271 2.042,0.344 10 false Power Back Door Unit Assembly (Power Back Door ECU) 0.469,2.771 2.24,2.917 1.771,0.146 10 false S32*1, S38*2 2.302,2.135 2.406,2.281 0.104,0.146 10 false 1 2.302,0.521 2.406,0.667 0.104,0.146 10 false 2 5.552,2.135 5.646,2.281 0.094,0.146 10 false 1 5.552,0.521 5.646,0.667 0.094,0.146 10 false 2 5.76,2.25 6.115,2.396 0.354,0.146 10 false DC- 5.76,0.646 6.115,0.792 0.354,0.146 10 false DC+ 1.99,2.375 2.208,2.521 0.219,0.146 10 false M- 1.99,0.76 2.208,0.906 0.219,0.146 10 false M+ 0.469,2.938 2.115,3.281 1.646,0.344 10 false Back Door Lock Assembly 1.125,1.427 2.167,2.146 1.042,0.719 10 false Back Door Lock Motor 0.125,3.375 1.771,3.563 1.646,0.188 10 false *1: w/ G-BOOK System 1.927,3.375 3.573,3.563 1.646,0.188 10 false *2: w/o G-BOOK System

PROCEDURE

1.INSPECT BACK DOOR LOCK ASSEMBLY (CLOSER MOTOR OPERATION)
a.

Remove the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>REMOVAL).


b.

Inspect the back door lock assembly (See page Vehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU])

NG

REPLACE BACK DOOR LOCK ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR UNIT ASSEMBLY [POWER BACK DOOR ECU])
a.

Disconnect the S32 back door lock assembly connector.


b.

Disconnect the L52 power back door unit assembly (power back door ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ G-BOOK System:
Tester Connection Condition Specified Condition
S38-2 (M+) - L52-2 (DC+) Always Below 1 Ω
S38-1 (M-) - L52-1 (DC-) Always Below 1 Ω
S38-2 (M+) - Body ground Always 10 kΩ or higher
S38-1 (M-) - Body ground Always 10 kΩ or higher

w/o G-BOOK System:
Tester Connection Condition Specified Condition
S32-2 (M+) - L52-2 (DC+) Always Below 1 Ω
S32-1 (M-) - L52-1 (DC-) Always Below 1 Ω
S32-2 (M+) - Body ground Always 10 kΩ or higher
S32-1 (M-) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR