Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052853 MIRROR (EXT) _0255766 POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)  Reverse Shift-linked Function of Power Mirrors does not Operate  


SYSTEM DESCRIPTION

When the reverse signal is sent from the ECM through the CAN communication line to the outer mirror control ECU, the outer mirror control ECU activates the outer rear view mirror LH and RH reverse shift-linked function.

HINT:

The reverse shift-linked function will not occur when the mirror master switch is in the neutral position (off).


PROCEDURE

1.CHECK DTC
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD) B
CAN DTC is output (for RHD) C



A

2.CHECK OPERATION OF SHIFT INDICATOR

B

C

2.CHECK OPERATION OF SHIFT INDICATOR
a.

Check that the shift indicator of the combination meter operates normally.

OK:

Shift indicator of combination meter operates normally.




OK

3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)

NG

3.READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)
a.

Check the Data List for proper functioning of the mirror position sensor (See page Vehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Retract Mirror)>DATA LIST / ACTIVE TEST).

Mirror
Tester Display Measurement Item/Display Normal Condition Diagnostic Note
RH Mir Position Sensor V RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
LH Mir Position Sensor V LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -

OK:

When mirror control switch is operated to turn mirror upward or downward, voltage changes within range shown in above chart.


Result
Result Proceed to
LH side mirror does not operate normally A
RH side mirror does not operate normally B
Mirror operates normally C



A

4.CHECK OUTER MIRROR CONTROL ECU

B

6.CHECK OUTER MIRROR CONTROL ECU

C

REPLACE OUTER MIRROR CONTROL ECU

4.CHECK OUTER MIRROR CONTROL ECU
U164086E01
0.844,1.116 1.073,1.280 0.228,0.164 10 I18 1.174,1.115 1.330,1.281 0.156,0.166 10 *1 0.844,1.394 1.073,1.558 0.228,0.164 10 I24 1.174,1.393 1.330,1.559 0.156,0.166 10 *2 3.551,2.265 3.824,2.431 0.273,0.166 10 LE1 4.027,2.116 4.319,2.282 0.292,0.166 10 LVC 0.121,2.027 0.835,2.194 0.714,0.166 10 *1: for LHD 0.125,2.324 0.886,2.490 0.762,0.166 10 *2: for RHD 3.655,2.244 3.668,1.289 false 4.143,2.1 3.758,1.289 false

a.

for LHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I18-2 (LVC) - I18-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-3 (LE1) - Body ground Always Below 1 Ω




b.

for RHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I24-2 (LVC) - I24-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-3 (LE1) - Body ground Always Below 1 Ω





OK

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)
a.
U164291E01
0.156,0.034 2.499,0.370 2.343,0.336 10 Front view of wire harness connector: (to Outer Rear View Mirror LH) 0.19,2.239 2.533,2.576 2.343,0.336 10 Front view of wire harness connector: (to Outer Mirror Control ECU) 0.168,1.108 0.415,1.264 0.246,0.156 10 I35 0.114,3.245 0.379,3.401 0.265,0.156 10 I18 0.441,3.239 0.645,3.395 0.205,0.156 10 *1 0.458,3.571 0.662,3.727 0.205,0.156 10 *2 0.126,3.571 0.362,3.727 0.237,0.156 10 I24 0.26,1.824 0.693,1.994 0.433,0.170 10 VSRL 3.125,0.866 3.381,1.036 0.257,0.170 10 VC 1.061,1.621 0.751,1.873 false 1.261,1.305 3.055,0.956 false 2.884,1.937 3.141,2.107 0.257,0.170 10 E1 1.256,1.615 2.802,2.016 false 1.19,4.128 1.505,4.266 0.316,0.139 10 LVC 0.061,4.039 1.051,4.178 0.990,0.139 10 *1: for LHD 0.061,4.325 1.051,4.464 0.990,0.139 10 *2: for RHD 1.724,4.15 2.040,4.289 0.316,0.139 10 LE1 3.004,2.917 3.320,3.055 0.316,0.139 10 VSR 1.019,3.587 1.367,4.107 false 1.135,3.583 1.806,4.111 false 1.26,3.51 2.966,3.007 false

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-2 (LVC) - I35-10 (VC) Always Below 1 Ω
I18-3 (LE1) - I35-21 (E1)
I18-4 (VSR) - I35-22 (VSRL)
I35-10 (VC) - Body ground Always 10 kΩ or higher
I35-21 (E1) - Body ground
I35-22 (VSRL) - Body ground




b.

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I35 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-2 (LVC) - I35-10 (VC) Always Below 1 Ω
I24-3 (LE1) - I35-21 (E1)
I24-4 (VSR) - I35-22 (VSRL)
I35-10 (VC) - Body ground Always 10 kΩ or higher
I35-21 (E1) - Body ground
I35-22 (VSRL) - Body ground





OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK OUTER MIRROR CONTROL ECU
U164087E02
3.677,2.292 3.667,1.438 false 4.167,2.146 3.76,1.438 false 0.844,1.115 1.073,1.281 0.229,0.167 10 false I18 1.177,1.115 1.333,1.281 0.156,0.167 10 false *1 0.844,1.396 1.073,1.563 0.229,0.167 10 false I24 1.177,1.396 1.333,1.563 0.156,0.167 10 false *2 3.552,2.302 3.854,2.469 0.302,0.167 10 false RE1 4.031,2.156 4.354,2.323 0.323,0.167 10 false RVC 0.125,2.031 0.844,2.198 0.719,0.167 10 false *1: for LHD 0.125,2.323 0.885,2.49 0.76,0.167 10 false *2: for RHD

a.

for LHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I18-22 (RVC) - I18-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-23 (RE1) - Body ground Always Below 1 Ω




b.

for RHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I24-22 (RVC) - I24-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-23 (RE1) - Body ground Always Below 1 Ω





OK

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)

NG

REPLACE OUTER MIRROR CONTROL ECU

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)
a.
U164292E01
0.156,0.034 2.499,0.370 2.343,0.336 10 Front view of wire harness connector: (to Outer Rear View Mirror RH) 0.19,2.239 2.533,2.576 2.343,0.336 10 Front view of wire harness connector: (to Outer Mirror Control ECU) 0.168,1.108 0.415,1.264 0.246,0.156 10 I32 0.114,3.245 0.379,3.401 0.265,0.156 10 I18 0.441,3.239 0.645,3.395 0.205,0.156 10 *1 0.458,3.571 0.662,3.727 0.205,0.156 10 *2 0.126,3.571 0.362,3.727 0.237,0.156 10 I24 0.26,1.824 0.693,1.994 0.433,0.170 10 VSSR 3.09,0.866 3.347,1.036 0.257,0.170 10 VC 1.061,1.621 0.751,1.873 false 1.261,1.305 3.02,0.956 false 2.884,1.937 3.141,2.107 0.257,0.170 10 E1 1.256,1.615 2.802,2.016 false 1.19,4.128 1.505,4.266 0.316,0.139 10 RVC 0.061,4.039 1.051,4.178 0.990,0.139 10 *1: for LHD 0.061,4.325 1.051,4.464 0.990,0.139 10 *2: for RHD 1.724,4.15 2.040,4.289 0.316,0.139 10 RE1 2.88,2.921 3.293,3.060 0.413,0.139 10 VSRR 1.019,3.742 1.367,4.107 false 1.135,3.738 1.806,4.111 false 1.26,3.664 2.828,3.007 false

for LHD:

i.

Disconnect the I18 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-22 (RVC) - I32-10 (VC) Always Below 1 Ω
I18-23 (RE1) - I32-21 (E1)
I18-24 (VSRR) - I32-22 (VSSR)
I32-10 (VC) - Body ground Always 10 kΩ or higher
I32-21 (E1) - Body ground
I32-22 (VSSR) - Body ground




b.

for RHD:

i.

Disconnect the I24 ECU connector.


ii.

Disconnect the I32 mirror connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I24-22 (RVC) - I32-10 (VC) Always Below 1 Ω
I24-23 (RE1) - I32-21 (E1)
I24-24 (VSRR) - I32-22 (VSSR)
I32-10 (VC) - Body ground Always 10 kΩ or higher
I32-21 (E1) - Body ground
I32-22 (VSSR) - Body ground





OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR