Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to the windshield wiper ECU and operates the front wiper motor.

WIRING DIAGRAM

E138462E03
5.572,1.581 5.836,1.762 0.264,0.181 10 E83 5.634,1.348 5.790,1.529 0.156,0.181 10 5 5.6,4.122 5.864,4.303 0.264,0.181 10 E85 5.664,3.93 5.863,4.111 0.199,0.181 10 10 5.969,4.112 6.125,4.294 0.156,0.181 10 E 5.525,4.589 7.047,4.770 1.522,0.181 10 Windshield Wiper ECU 0.621,1.572 1.572,1.753 0.951,0.181 10 from IG1 Relay 3.636,1.767 4.519,1.923 0.883,0.156 10 ECU-IG No. 1 5.973,1.59 6.481,1.746 0.508,0.156 10 IG1L

PROCEDURE

1.INSPECT FUSE (ECU-IG No. 1)
a.

Remove the ECU-IG No. 1 fuse from the main body ECU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-IG No. 1 fuse Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER ECU - BATTERY AND BODY GROUND)
a.
E349760E01
2.656,1.313 2.948,1.51 0.292,0.198 2.594,3.552 2.885,3.75 0.292,0.198 2.438,4.365 1.781,3.969 true 0.635,2.073 1.052,1.656 true 0.49,0.094 2.781,0.792 2.292,0.698 10 false Front view of wire harness connector: (to Windshield Wiper ECU) 0.396,2.104 0.885,2.354 0.49,0.25 10 false IGIL 2.688,1.333 3.177,1.583 0.49,0.25 10 false E83 2.604,3.573 3.094,3.823 0.49,0.25 10 false E85 2.49,4.302 2.75,4.542 0.26,0.24 10 false E

Disconnect the E83 and E85 windshield wiper ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E83-5 (IG1L) - Body ground Engine switch on (IG) 11 to 14 V
E83-5 (IG1L) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E85-10 (E) - Body ground Always Below 1 Ω




OK

REPLACE WINDSHIELD WIPER ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR