Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) C

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  B1400  Rain Sensor Malfunction  


DESCRIPTION

When the windshield wiper switch assembly position is set to AUTO, the rain sensor detects the amount of raindrops. According to the amount of raindrops, the rain sensor sends wiper drive request signals to the windshield wiper ECU at the optimal timings via LIN communication. Also, the vehicle speed-sensitive intermittent operation is still performed even when there is a rain sensor malfunction.

DTC Code DTC Detection Condition Trouble Area
B1400

The rain sensor output signal is not detected.


·

Rain sensor

·

Map light assembly

·

Harness or connector



WIRING DIAGRAM

E305857E02
0.667,2.292 2.573,2.531 1.906,0.24 10 false : LIN Communication Line 4.729,1.708 5.646,1.906 0.917,0.198 10 false Rain Sensor 2.948,1.74 4.479,1.938 1.531,0.198 10 false Map Light Assembly 3.094,0.74 3.406,0.938 0.313,0.198 10 false IG 3.083,1.188 3.698,1.385 0.615,0.198 10 false GND5 3.833,0.74 4.146,0.938 0.313,0.198 10 false IG2 3.688,1.177 4.302,1.375 0.615,0.198 10 false GND2 4.875,0.625 5.188,0.823 0.313,0.198 10 false SIG 4.885,1.063 5.198,1.26 0.313,0.198 10 false ES 1.969,0.771 3.656,0.969 1.688,0.198 10 false ECU-IG No.2 0.313,0.594 2,0.792 1.688,0.198 10 false from IG1 NO. 3 Relay 2.781,0.479 3.094,0.677 0.313,0.198 10 false 14 2.854,0.938 3.167,1.135 0.313,0.198 10 false 3 4.208,0.479 4.521,0.677 0.313,0.198 10 false 29 4.24,0.938 4.552,1.135 0.313,0.198 10 false 4 4.625,0.927 4.938,1.125 0.313,0.198 10 false 1 4.615,0.469 4.927,0.667 0.313,0.198 10 false 4 5.802,1.51 7.156,1.906 1.354,0.396 10 false Windshield Wiper ECU 0.667,2.01 2.51,2.208 1.844,0.198 10 false : CAN Communication Line 2.958,1.531 3.573,1.729 0.615,0.198 10 false R7 4.708,1.552 5.323,1.75 0.615,0.198 10 false R11

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Since the wiper and washer system has functions that use LIN communication and CAN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions and CAN communication in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Check the Data List for proper functioning of the rain sensor.

Rain Sensor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Sensor Low Temp Info Rain sensor low temp / NG or OK NG: Rain sensor is low temp
OK: Rain sensor is normal
-
Sensor High Temp Info Rain sensor high temp / NG or OK NG: Rain sensor is high temp
OK: Rain sensor is normal
-

OK:

The display is as specified in the normal condition.




OK

2.INSPECT MAP LIGHT ASSEMBLY

NG

2.INSPECT MAP LIGHT ASSEMBLY

b.
E305858E02
0.448,0.26 0.615,0.26 0.615,0.26 0.938,1.031 true 2.073,0.188 2.24,0.188 2.24,0.188 2.333,1.01 true 2.479,1.01 2.5,0.26 2.5,0.26 2.698,0.26 true 0.781,1.875 0.969,1.875 0.969,1.875 1.063,1.292 true 0.26,0.177 0.573,0.375 0.313,0.198 10 false IG 2.719,0.167 3.333,0.365 0.615,0.198 10 false GND5 0.521,1.792 0.833,1.99 0.313,0.198 10 false IG2 1.635,0.125 2.25,0.323 0.615,0.198 10 false GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (GND5) - 4 (GND2) Always Below 1 Ω
14 (IG) - 29 (IG2) Always Below 1 Ω


Result
Result Proceed to
OK A
NG (w/ Sliding Roof) B
NG (w/o Sliding Roof) C



A

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)

B

C

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165794E02
1.052,1.958 1.292,2.729 1.292,2.729 1.469,2.729 true 2.417,1.854 2.688,1.083 2.688,1.083 2.833,1.083 true 0.052,0 2.417,0.323 2.365,0.323 10 false Front view of wire harness connector: (to Map Light) 0.26,1.844 0.469,2.031 0.208,0.188 10 false R7 2.896,1.01 3.104,1.198 0.208,0.188 10 false IG 1.51,2.635 1.938,2.823 0.427,0.188 10 false GND5

Disconnect the R7 map light connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-3 (GND5) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R7-14 (IG) - Body ground Engine switch on (IG) 11 to 14 V
R7-14 (IG) - Body ground Engine switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RAIN SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - RAIN SENSOR)
a.
U166482E02
1.344,3.854 1.125,4.396 1.125,4.396 0.979,4.396 true 2.135,3.875 2.354,4.417 2.354,4.417 2.5,4.417 true 1.292,1.542 1.052,1.01 1.052,1.01 0.917,1.01 true 2.417,1.813 2.563,2.198 2.563,2.198 2.677,2.198 true 0.479,0.104 2.833,0.448 2.354,0.344 10 false Front view of wire harness connector: (to Map Light) 0.479,2.646 2.833,2.99 2.354,0.344 10 false Front view of wire harness connector: (to Rain Sensor) 0.25,1.49 0.448,1.667 0.198,0.177 10 false R7 0.479,0.938 0.885,1.115 0.406,0.177 10 false GND2 2.542,4.323 2.802,4.5 0.26,0.177 10 false SIG 0.698,4.302 0.896,4.479 0.198,0.177 10 false ES 2.74,2.104 2.979,2.281 0.24,0.177 10 false IG2 0.635,3.677 0.906,3.854 0.271,0.177 10 false R11

Disconnect the R7 map light connector.


b.

Disconnect the R11 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R7-4 (GND2) - R11-1 (ES) Always Below 1 Ω
R7-29 (IG2) - R11-4 (SIG)
R7-4 (GND2) - Body ground Always 10 kΩ or higher
R7-29 (IG2) - Body ground




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR