Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › from 2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Washer Nozzle Heater Circuit  


DESCRIPTION

The No. 2 multiplex network body ECU receives ambient air temperature information from the air conditioning amplifier assembly via CAN communication.

The washer nozzle heater assembly controls the No. 2 multiplex network body ECU and operates the washer nozzle heater assembly according to the ambient temperature.

WIRING DIAGRAM

E273238E01
2.923,1.738 4.749,1.904 1.827,0.166 10 Cowl Side Junction Block RH 2.302,2.798 4.129,2.964 1.827,0.166 10 z70 2.302,2.963 4.767,3.129 2.465,0.166 10 Washer Nozzle Heater Assembly LH 2.302,3.972 4.129,4.138 1.827,0.166 10 z69 2.302,4.137 4.767,4.303 2.465,0.166 10 Washer Nozzle Heater Assembly RH 0.41,4.372 2.876,4.538 2.465,0.166 10 : CAN Communication Line 5.39,1.524 6.890,1.867 1.500,0.343 10 No. 2 Multiplex Network Body ECU 5.348,3.187 6.937,3.531 1.589,0.343 10 Air Conditioning Amplifier Assembly 5.39,1.337 6.911,1.503 1.522,0.166 10 L50 1.523,0.786 2.442,0.952 0.919,0.166 10 ECU-IG No. 4 3.393,1.344 4.367,1.510 0.974,0.166 10 WSH NZL HTR 2.846,0.61 3.064,0.776 0.218,0.166 10 3C 2.846,1.028 3.064,1.194 0.218,0.166 10 3B 4.704,0.61 4.922,0.776 0.218,0.166 10 3B 5.306,0.51 5.524,0.676 0.218,0.166 10 25 5.575,0.589 6.302,0.755 0.727,0.166 10 WHTR 4.704,1.028 4.922,1.194 0.218,0.166 10 3C 2.846,0.411 3.064,0.577 0.218,0.166 10 16 2.65,2.352 2.868,2.518 0.218,0.166 10 1 2.843,2.451 3.061,2.617 0.218,0.166 10 L- 3.777,2.451 3.996,2.617 0.218,0.166 10 L+ 4.033,2.352 4.251,2.518 0.218,0.166 10 2 2.65,3.523 2.868,3.689 0.218,0.166 10 1 2.843,3.621 3.061,3.787 0.218,0.166 10 R- 3.777,3.621 3.996,3.787 0.218,0.166 10 R+ 4.033,3.523 4.251,3.689 0.218,0.166 10 2 2.888,0.844 3.106,1.010 0.218,0.166 10 5 4.704,0.411 4.922,0.577 0.218,0.166 10 11 4.746,0.844 4.964,1.010 0.218,0.166 10 2 0.087,0.591 1.608,0.757 1.522,0.166 10 from IG NO. 4 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Since the wiper and washer system has functions that use CAN communication, first confirm that there is no malfunction in the CAN communication system with the How to Proceed with Troubleshooting procedure (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM(w/ Rain Sensor)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Since the wiper and washer system has functions that use the air conditioning system, first confirm that there is no malfunction in the air conditioning system with the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK NO. 2 MULTIPLEX NETWORK BODY ECU
a.
U166091E02
0.979,2.01 0.76,2.563 true 0.219,1.542 0.469,1.719 0.25,0.177 10 false L50 0.396,0.208 2.688,0.563 2.292,0.354 10 false Component with harness connected: (No. 2 Multiplex Network Body ECU) 0.531,2.573 1.313,2.896 0.781,0.323 10 false WHTR

Using the intelligent tester, enter the following menus: Body / Body No. 4 / Active Test.


b.

Select "Front Washer Nozzle Heater", and perform the Active Test.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L50-25 (WHTR) - Body ground
·

Engine switch on (IG)

·

Active Test is not performed


11 to 14 V
L50-25 (WHTR) - Body ground
·

Engine switch on (IG)

·

Active Test is performed


Below 1 V




OK

2.INSPECT WASHER NOZZLE HEATER ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (NO. 2 MULTIPLEX NETWORK BODY ECU - COWL SIDE JUNCTION BLOCK RH)
2.INSPECT WASHER NOZZLE HEATER ASSEMBLY
a.

for LH:

i.

Remove the washer nozzle heater assembly LH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>REMOVAL).


ii.

Inspect the washer nozzle heater assembly LH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>INSPECTION).



b.

for RH:

i.

Remove the washer nozzle heater assembly RH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>REMOVAL).


ii.

Inspect the washer nozzle heater assembly RH (See page Vehicle Exterior>WIPER / WASHER>WASHER NOZZLE (for Front Side)>INSPECTION).



Result
Result Proceed to
OK A
NG (for LH) B
NG (for RH) C


A

3.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE HEATER ASSEMBLY - COWL SIDE JUNCTION BLOCK RH AND BODY GROUND)

B

REPLACE WASHER NOZZLE HEATER ASSEMBLY LH

C

REPLACE WASHER NOZZLE HEATER ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE HEATER ASSEMBLY - COWL SIDE JUNCTION BLOCK RH AND BODY GROUND)
a.

Disconnect the z70 washer nozzle heater assembly LH connector.

U166436E01
0.039,0 2.364,0.515 2.325,0.515 10 Front view of wire harness connector: (to Washer Nozzle Heater Assembly LH) 2.427,0 4.753,0.515 2.326,0.515 10 Front view of wire harness connector: (to Washer Nozzle Heater Assembly RH) 4.809,0 7.138,0.515 2.329,0.515 10 Front view of wire harness connector: (to Cowl Side Junction Block RH) 1.083,1.127 1.324,1.308 0.241,0.181 10 z70 3.468,1.127 3.708,1.308 0.241,0.181 10 z69 5.847,1.127 6.041,1.308 0.195,0.181 10 3C 1.372,1.96 1.557,2.258 false 1.045,1.96 0.86,2.258 false 0.75,2.289 0.933,2.441 0.183,0.152 10 L- 1.514,2.289 1.697,2.441 0.183,0.152 10 L+ 3.762,1.96 3.947,2.258 false 3.436,1.96 3.25,2.258 false 3.14,2.289 3.323,2.441 0.183,0.152 10 R- 3.904,2.289 4.102,2.441 0.198,0.152 10 R+


b.

Disconnect the z69 washer nozzle heater assembly RH connector.


c.

Disconnect the 3C cowl side junction block RH connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z70-2 (L+) - 3C-2 Always Below 1 Ω
z69-2 (R+) - 3C-2 Always Below 1 Ω
z70-1 (L-) - Body ground Always Below 1 Ω
z69-1 (R-) - Body ground Always Below 1 Ω
z70-2 (L+) or 3C-2 - Body ground Always 10 kΩ or higher
z69-2 (R+) or 3C-2 - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY)
a.
U166437E03
0.49,0.125 2.833,0.479 2.344,0.354 10 false Front view of wire harness connector: (to Cowl Side Junction Block RH) 0.365,1.219 0.552,1.396 0.188,0.177 10 false 3B

Disconnect the 3B cowl side junction block RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3B-5 - Body ground Engine switch on (IG) 11 to 14 V
3B-5 - Body ground Engine switch off Below 1 V




OK

5.CHECK COWL SIDE JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COWL SIDE JUNCTION BLOCK RH
a.
U166440E04
0.26,0.073 2.74,0.427 2.479,0.354 10 false Component without harness connected: (Cowl Side Junction Block RH) 0.594,1.333 0.781,1.51 0.188,0.177 10 false 3B 0.281,2.604 0.479,2.781 0.198,0.177 10 false 3C

Remove the cowl side junction block RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-5 - 3C-2 Battery voltage applied between terminals 3C-16 and 3B-11 Below 1 Ω
3B-5 - 3C-2 Battery voltage not applied between terminals 3C-16 and 3B-11 10 kΩ or higher


Result
Result Proceed to
OK (w/ Sliding Roof System) A
OK (w/o Sliding Roof System) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (NO. 2 MULTIPLEX NETWORK BODY ECU - COWL SIDE JUNCTION BLOCK RH)
a.
U166439E02
2.521,1.698 2.75,2.031 true 0.313,0.063 2.74,0.396 2.427,0.333 10 false Front view of wire harness connector: (to No. 2 Multiplex Network Body ECU) 0.354,2.385 2.698,2.719 2.344,0.333 10 false Front view of wire harness connector: (to Cowl Side Junction Block RH) 0.167,1.448 0.417,1.625 0.25,0.177 10 false L50 0.406,3.688 0.594,3.865 0.188,0.177 10 false 3B 2.615,2.104 3.115,2.26 0.5,0.156 10 false WHTR

Disconnect the L50 No. 2 multiplex network body ECU connector.


b.

Disconnect the 3B cowl side junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L50-25 (WHTR) - 3B-11 Always Below 1 Ω
L50-25 (WHTR) or 3B-11 - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COWL SIDE JUNCTION BLOCK RH - BATTERY)
a.
U166438E04
0.417,0.115 2.75,0.448 2.333,0.333 10 false Front view of wire harness connector: (to Cowl Side Junction Block RH) 0.219,1.365 0.417,1.542 0.198,0.177 10 false 3C

Disconnect the 3C cowl side junction block RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3C-16 - Body ground Engine switch on (IG) 11 to 14 V
3C-16 - Body ground Engine switch off Below 1 V




OK

8.INSPECT COWL SIDE JUNCTION BLOCK RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT COWL SIDE JUNCTION BLOCK RH
a.
U166440E04
0.26,0.073 2.74,0.427 2.479,0.354 10 false Component without harness connected: (Cowl Side Junction Block RH) 0.594,1.333 0.781,1.51 0.188,0.177 10 false 3B 0.281,2.604 0.479,2.781 0.198,0.177 10 false 3C

Remove the cowl side junction block RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-5 - 3C-2 Battery voltage applied between terminals 3C-16 and 3B-11 Below 1 Ω
3B-5 - 3C-2 Battery voltage not applied between terminals 3C-16 and 3B-11 10 kΩ or higher


Result
Result Proceed to
OK (w/ Sliding Roof System) A
OK (w/o Sliding Roof System) B
NG C



A

B

C

REPLACE COWL SIDE JUNCTION BLOCK RH