Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (w/o Sliding Roof) › from 2015.08
RM2660E _58 Vehicle Interior _052849 INTERIOR PANELS / TRIM _0255719 ROOF HEADLINING(w/o Sliding Roof) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(w/o Sliding Roof)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 64910J 3.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.

Remove the tonneau cover assembly.


Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)

Hide 5.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 6.REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)

Hide 7.REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 67914B 8.REMOVE FRONT DOOR SCUFF PLATE LH

B448829

a.

Detach the 7 claws and 4 clips, and remove the front door scuff plate LH.


Hide 67913B 9.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 51775 10.REMOVE REAR STEP COVER

HINT:

Use the same procedure for both rear step covers.


a.
B181673

Detach the 2 claws and remove the rear step cover.


Hide 67918E 11.REMOVE REAR DOOR SCUFF PLATE LH

B181674

a.

Remove the screw.


b.

Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.


Hide 67917C 12.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 58574A 13.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672

a.

Detach the 6 clips and remove the rear floor mat support plate.


Hide 74610A 14.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both assist grip sub-assemblies.


a.
B181684

Detach the 4 claws and remove the 2 assist grip plugs.


b.
B181685

Remove the 2 bolts.


c.

Detach the 2 claws and remove the assist grip sub-assembly.


Hide 62212 15.REMOVE FRONT PILLAR GARNISH LH

B185447

a.

Detach the clip 3 guides, and remove the front pillar garnish LH.


b.

w/ Speaker:

Disconnect the speaker connector and then remove the front pillar garnish.


c.
U155784E04
2.198,0.177 1.667,0.573 true 2.76,1.052 1.802,1.615 true 0.698,1.823 1.5,1.583 true 2.26,0.042 2.448,0.219 0.188,0.177 10 false *a 2.813,0.927 3,1.104 0.188,0.177 10 false *b 0.49,1.771 0.677,1.948 0.188,0.177 10 false *c

Protect the curtain shield airbag.

i.

Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


Text in Illustration
*a Adhesive Tape
*b Protective Cover
*c Curtain Shield Airbag Assembly LH



Hide 62211 16.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62422 17.REMOVE CENTER PILLAR GARNISH COVER LH

HINT:
·

for Manual Seat:

When removing the center pillar garnish cover LH, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When removing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181676

Detach the 2 clips and 2 guides, and remove the center pillar garnish cover LH.


Hide 62421 18.REMOVE CENTER PILLAR GARNISH COVER RH

HINT:

Use the same procedures described for the LH side.


Hide 62414A 19.REMOVE CENTER LOWER PILLAR GARNISH LH

HINT:
·

for Manual Seat:

When removing the center lower pillar garnish LH, move the front seat and seatback to the foremost upright position.

·

for Power Seat:

When removing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

·

for Power Seat:

After moving the front seat, disconnect the cable from the negative (-) battery terminal.



a.
B181677

Remove the bolt and seat belt anchor.


b.
B181678

Detach the 2 claws and 7 clips, and remove the center lower pillar garnish LH..


Hide 62413A 20.REMOVE CENTER LOWER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 74620A 21.REMOVE REAR ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both rear assist grip assemblies.


a.
B181679

Detach the 4 claws and remove the 2 assist grip plugs.


b.
B181680

Remove the 2 bolts.


c.

Detach the 2 claws and remove the rear assist grip assembly.


Hide 62412 22.REMOVE CENTER PILLAR GARNISH LH

B181681

a.

Remove the bolt.


b.

Detach the 2 clips and 2 guides.


c.

Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish LH.


Hide 62411 23.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 64937A 24.REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

HINT:

Use the same procedure for both No. 1 tonneau cover holder caps.


B186439

a.

Detach the 2 claws and remove the No. 1 tonneau cover holder cap.


Hide 71845B 25.REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedure for both No. 1 luggage compartment trim hooks.


a.
U155858E01
1.295,0.491 1.487,0.670 0.192,0.179 10 *a 1.298,0.989 1.37,0.695 false

Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


Hide 62520P 26.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644

HINT:

When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.
B181687

Detach the 3 claws and remove the outer lap belt anchor cover.


b.
B181689

Remove the bolt and rear No. 1 seat belt anchor.


c.
B181691

w/ Rear No. 2 Seat, except Face to Face Seat Type:

Remove the bolt and rear No. 2 seat belt anchor.


d.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Remove the clip and bolt.


ii.

Detach the 18 clips and 2 claws.


iii.

w/o Rear Air Conditioning System:

Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly LH.


iv.

w/ Rear Air Conditioning System:

Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly LH.

B186889



e.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Remove the clip.


ii.

Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.

B190221



f.

w/ Tonneau Cover:

i.

Remove the screw and clip.


ii.

Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.

B186437



Hide 62510P 27.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:

When removing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


a.
B181688

Detach the 3 claws and remove the outer lap belt anchor cover.


b.
B181690

Remove the bolt and rear No. 1 seat belt anchor.


c.
B181692

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Detach the 3 claws and remove the outer lap belt anchor cover.


ii.
B181693

Remove the bolt and rear No. 2 seat belt anchor.



d.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.

Remove the clip and bolt.


ii.

Detach the 16 clips and 2 claws.


iii.

w/o Rear Air Conditioning System:

Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly RH.


iv.

w/ Rear Air Conditioning System:

Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly RH.

B186890



e.

w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

i.

Remove the clip.


ii.

Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.

B190220



f.

w/ Tonneau Cover:

i.

Remove the screw and clip.


ii.

Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.

B186438



Hide 62639 28.REMOVE REAR FRONT QUARTER TRIM GARNISH LH

B181703

a.

Remove the screw.


b.

Detach the clip and 2 guides.


c.

Pass the seat belt anchor through the rear front quarter trim garnish LH, and remove the rear front quarter trim garnish LH.


Hide 62638 29.REMOVE REAR FRONT QUARTER TRIM GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62472D 30.REMOVE REAR UPPER PILLAR GARNISH LH

a.

w/ Rear No. 2 Seat, except Face to Face Seat Type:

i.
U155820E01
1.358,1.665 0.753,1.882 false 0.527,1.813 0.719,1.992 0.192,0.179 10 *a

Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


ii.
B183809

Remove the bolt and seat belt shoulder anchor.



b.
B181702

Detach the 5 clips and remove the rear upper pillar garnish LH.


Hide 67939B 31.REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)

Hide 67937B 32.REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

Hide 67847 33.REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

Hide 62471D 34.REMOVE REAR UPPER PILLAR GARNISH RH

U155820E01
1.358,1.665 0.753,1.882 false 0.527,1.813 0.719,1.992 0.192,0.179 10 *a

a.

Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


b.
B195963

Remove the bolt and seat belt shoulder anchor.


c.
B184328

w/o Power Back Door:

i.

Detach the 5 clips and remove the rear upper pillar garnish RH.



d.
U157045E01
3.133,1.943 3.088,1.453 false 3.053,1.939 3.245,2.118 0.192,0.179 10 *a

w/ Power Back Door:

i.

Detach the 5 clips.


ii.

Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish RH.

Text in Illustration
*a Power Back Door Rod



Hide 81260A 35.REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 81240 36.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 81290 37.REMOVE NO. 3 ROOM LIGHT ASSEMBLY

Hide 74325 38.REMOVE VISOR BRACKET COVER

HINT:

Use the same procedure for both visor bracket covers.


a.
B181706

Detach the 4 claws and remove the visor bracket cover.


Hide 74320 39.REMOVE VISOR ASSEMBLY LH

B181707

a.

Remove the 2 screws and visor assembly LH.


Hide 74310 40.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74348 41.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B151362E02
0.781,0.361 1.312,0.642 0.531,0.281 10 45°

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Detach the 2 claws and remove the visor holder.


Hide 74330C 42.REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

U155785E01
2.464,1.751 2.657,1.931 0.193,0.180 10 *a 0.658,1.529 0.850,1.708 0.192,0.179 10 *b 1.456,1.847 0.88,1.66 false 2.191,1.752 2.427,1.823 false

a.

Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor assembly LH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape
*b Cover


Hide 74330B 43.REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

HINT:

Use the same procedures described for the LH side.


Hide 87834 44.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89943 45.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 86466E 46.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466D 47.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 73139B 48.REMOVE SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

B181709

a.

Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.


Hide 74610U 49.REMOVE ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both assist grip assemblies.


a.
U155825E01
1.709,0.516 1.852,0.23 false 1.769,0.074 1.961,0.253 0.192,0.179 10 *a

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


b.

ach the 2 clips and remove the assist grip assembly.


c.

Remove the 2 clips from the vehicle body.


Hide 74610K 50.REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH

a.

w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

Remove the No. 2 assist grip assembly.

i.
U155827E01
1.684,0.499 1.822,0.211 false 1.727,0.061 1.919,0.240 0.192,0.179 10 *a

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


ii.

Detach the 2 clips and remove the No. 2 assist grip assembly LH.


iii.

Remove the 2 clips from the vehicle body.



b.

w/ Rear No. 2 Seat, for Face to Face Seat Type:

Remove the No. 2 assist grip assembly.

i.
U155825E01
1.709,0.516 1.852,0.23 false 1.769,0.074 1.961,0.253 0.192,0.179 10 *a

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


ii.

Detach the 2 clips and remove the No. 2 assist grip assembly LH.


iii.

Remove the 2 clips from the vehicle body.



Hide 74610B 51.REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 74630B 52.REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat except Face to Face Seat Type)

HINT:

Use the same procedure for both 3rd seat assist grip assemblies.


a.
U155826E01
1.709,0.516 1.852,0.23 false 1.767,0.066 1.958,0.245 0.192,0.179 10 *a

Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*a Protective Tape


b.

Detach the 2 clips and remove the 3rd seat assist grip assembly.


c.

Remove the 2 clips from the vehicle body.


Hide 63310 53.REMOVE ROOF HEADLINING ASSEMBLY

B183934

HINT:
·

for Manual Seat:

When removing the roof headlining assembly, move the front seat and rear No. 1 seat to the position shown in the illustration.

·

for Power Seat:

When removing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

·

for Power Seat:

After moving the seats, disconnect the cable from the negative (-) battery terminal.



a.
B430357

w/ EC Mirror:

Disconnect the connector.


b.
B430358

w/ Rain Sensor:

Disconnect the connector.


c.

w/ Pre-crash Safety System:

i.
B430359

w/o Camera Heater:

Disconnect the 2 connectors.


ii.
B478233

w/ Camera Heater:

Disconnect the 3 connectors.



d.
U155787E01
2.307,0.87 2.35,1.112 false 0.132,0.049 0.324,0.229 0.192,0.179 10 *a 2.183,0.682 2.375,0.861 0.192,0.179 10 *b

Disconnect the 3 roof wire connectors.

i.

w/ Rear Wiper:

Disconnect the washer hose.



e.

Detach the 4 clamps.

Text in Illustration
*a Front Left Side
*b Washer Hose


f.
U155786E01
0.116,0 0.308,0.179 0.192,0.179 10 *a

Remove the bolt.


g.

Disconnect the antenna cord connector and detach the 2 clamps.

Text in Illustration
*a Front Right Side


h.
U155788E01
0.094,0.012 0.286,0.191 0.192,0.179 10 *a

Disconnect the antenna cord connector.

Text in Illustration
*a Rear Right Side


i.
U155789E01
0.203,0.338 0.638,0.693 0.435,0.355 0.12,0.048 0.312,0.227 0.192,0.179 10 *a

w/ Rear Wiper:

Disconnect the washer hose.

Text in Illustration
*a Rear Left Side


j.

for 3 Person Seat Type Rear No. 2 Seat:

Detach the 12 claws, 2 clips and 2 guides.

U164113E01
0.16,0.041 0.351,0.220 0.192,0.179 10 *A

Text in Illustration
*A for 3 Person Seat Type Rear No. 2 Seat - -


k.

except 3 Person Seat Type Rear No. 2 Seat:

Detach the 12 claws, 3 clips and 2 guides.

U164114E01
0.158,0.034 0.350,0.213 0.192,0.179 10 *A

Text in Illustration
*A except 3 Person Seat Type Rear No. 2 Seat - -


l.
B188644

Remove the roof headlining assembly from the rear of the vehicle as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when taking it out.



Hide 62432C 54.REMOVE FRONT ROOF SIDE RAIL GARNISH LH

U155801E01
2.28,1.997 1.848,2.492 false 1.662,2.472 1.853,2.651 0.192,0.179 10 *a

a.

Detach the 3 clips.


b.

Cut off the 3 clips and remove the front roof side rail garnish LH.


c.

Remove 3 clips from the vehicle body.

Text in Illustration
*a Cut Off Position


Hide 62431C 55.REMOVE FRONT ROOF SIDE RAIL GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62312B 56.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B182479

a.

Remove the front door opening trim weatherstrip LH.


Hide 62311B 57.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 62332A 58.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B182481

a.

Remove the rear door opening trim weatherstrip LH.


Hide 62331A 59.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 67881A 60.REMOVE BACK DOOR WEATHERSTRIP

B190020

a.

Remove the back door weatherstrip.


Hide 67912A 61.REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

U155781E01
0.812,1.245 1.352,0.734 false 0.632,1.224 0.823,1.403 0.192,0.179 10 *a

a.

Put protective tape around the front door scuff plate outside LH.

Text in Illustration
*a Protective Tape


b.

Detach the 4 clips and remove the front door scuff plate outside LH.


Hide 67911B 62.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedures described for the LH side.


Hide 67916 63.REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

U155780E01
0.653,1.51 0.845,1.689 0.192,0.179 10 *a 1.301,0.935 0.813,1.522 false

a.

Put protective tape around the rear door scuff plate outside LH.

Text in Illustration
*a Protective Tape


b.

Detach the 3 clips and remove the rear door scuff plate outside LH.


Hide 67915 64.REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

HINT:

Use the same procedures described for the LH side.


Hide 73024 65.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182424

a.

Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.


Hide 73023 66.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 73034 67.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182423

a.

Detach the 6 claws and remove the rear shoulder belt anchor plate sub-assembly LH.


Hide 73033 68.REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 62488A 69.REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182427

a.

Detach the 7 claws and remove the roof side inner garnish cover LH.


Hide 62487A 70.REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 73371A 71.REMOVE REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedure for both rear No. 1 seat shoulder belt hangers.


a.
U155800E01
1.556,0.157 1.748,0.336 0.192,0.179 10 *a 1.156,0.229 1.348,0.408 0.192,0.179 10 *a

Remove the 2 spring nuts and rear No. 1 seat shoulder belt hanger.

Text in Illustration
*a Spring Nut


Hide 73372C 72.REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH

U155799E01
2.381,0.542 2.572,0.721 0.192,0.179 10 *a 2.71,0.505 2.902,0.684 0.192,0.179 10 *a

a.

Remove the 2 spring nuts and rear No. 2 seat shoulder belt hanger.

Text in Illustration
*a Spring Nut


Hide 73371C 73.REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

HINT:

Use the same procedures described for the LH side.


Hide 62502B 74.REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH

B182411

a.

w/ Rear Heater:

Remove the 8 screws and duct.


b.
B182412

Remove the 7 screws.


c.

Detach the 4 claws and remove the quarter trim cover sub-assembly LH.


Hide 62501C 75.REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH

B182414

a.

Remove the 7 screws.


b.

Detach the 4 claws and remove the quarter trim cover sub-assembly RH.


Hide 66992 76.REMOVE NO. 2 CUP HOLDER

B182416

a.

Remove the 5 screws.


b.

Detach the 3 claws and remove the No. 2 cup holder.


Hide 66991B 77.REMOVE NO. 1 CUP HOLDER

B182418

a.

Remove the 5 screws.


b.

Detach the 3 claws and remove the No. 1 cup holder.


Hide 64934A 78.REMOVE TONNEAU COVER HOLDER BRACKET LH (w/ Tonneau Cover)

U164064E01
2.294,3.762 2.555,3.862 0.261,0.1 1.081,0.521 1.272,0.700 0.192,0.179 10 *a 1.992,0.745 1.283,0.651 false

a.

Remove the 8 screws.


b.

Detach the 3 claws and remove the tonneau cover holder bracket LH and front quarter trim base.

Text in Illustration
*a Front Quarter trim base


Hide 64933A 79.REMOVE TONNEAU COVER HOLDER BRACKET RH (w/ Tonneau Cover)

HINT:

Use the same procedures described for the LH side.


Hide 64932B 80.REMOVE TONNEAU COVER HANGER LH (w/ Tonneau Cover)

U164066E01
1.515,0.281 2.127,0.484 false 1.303,0.14 1.495,0.319 0.192,0.179 10 *a

a.

Remove the 2 screws, tonneau cover hanger LH and rear quarter trim base.

Text in Illustration
*a Rear Quarter trim base


Hide 64931B 81.REMOVE TONNEAU COVER HANGER RH (w/ Tonneau Cover)

HINT:

Use the same procedures described for the LH side.


Hide 62525D 82.REMOVE NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182420

a.

Detach the 4 claws and remove the No. 1 side trim base cover LH.


Hide 62515B 83.REMOVE NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

B185344

a.

Remove the 6 screws and duct.


b.
B187176

Detach the 4 claws and remove the No. 1 side trim base cover RH.


Hide 62526D 84.REMOVE NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182421

a.

Detach the 4 claws and remove the No. 2 side trim base cover LH.


Hide 62516B 85.REMOVE NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

HINT:

Use the same procedures described for the LH side.


Hide 72058C 86.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

Hide 72057A 87.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 71866B 88.REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B181698

a.

Detach the 6 clips and remove the rear No. 2 seat cover bezel.


Hide 71865A 89.REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:

Use the same procedures described for the rear No. 2 seat cover bezel.


Hide 62522A 90.REMOVE QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

B188391

a.

Detach the 6 clips and remove the quarter trim cover LH.


Hide 62521B 91.REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

HINT:

Use the same procedures described for the LH side.


Hide 62605Q 92.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH

a.

Remove the quarter trim lid sub-assembly RH.


Hide 62598D 93.REMOVE SIDE TRIM BOX COVER

a.

Remove the side trim box cover.


Hide 62597A 94.REMOVE SIDE TRIM BOX

B185343

a.

Remove the 9 screws and side trim box.