Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › from 2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255784 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
E156196

Using a T30 "TORX" socket, install the wiper motor with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Apply MP grease to the crank arm pivot of the windshield wiper motor assembly.


c.
E156194

Install the No. 1 windshield wiper link rod to the crank arm pivot of the windshield wiper motor assembly.


d.
E156195

Install the No. 2 windshield wiper link rod to the crank arm pivot of the windshield wiper motor assembly.


e.
E161961

Install the wiper motor cover with the clamp.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

a.
B184646E05
1.49,0.125 1.604,0.125 1.604,0.125 1.677,0.365 false 1.313,1.875 1.448,1.875 1.448,1.875 1.448,1.771 false 2.604,0.115 2.833,0.354 0.229,0.24 10 true (1) 0.552,0.115 0.771,0.417 0.219,0.302 10 true (2) 0.448,1.042 0.698,1.323 0.25,0.281 10 true (3) 1.271,0.042 1.479,0.26 0.208,0.219 10 true *a 1.135,1.781 1.573,2.042 0.438,0.26 10 false *1

Slide and attach the motor grommet to temporarily install the windshield wiper motor and link assembly as shown in the illustration.

Text in Illustration
*1 Motor Grommet
*a Slide


b.

Install the windshield wiper motor and link assembly with the 3 bolts in the order indicated in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.

Connect the connector.


Hide 55781E 3.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E156191

Attach the 17 claws and 2 clips and install the cowl top ventilator louver sub-assembly.


b.
E156188

Install the washer hose.


c.

w/ PTC Heater:

i.

Connect the connector.



Hide 53383 4.INSTALL HOOD TO COWL TOP SEAL

a.
E156189

Attach the 12 clips and 4 clamps to install the hood to cowl top seal.


Hide 53883F 5.INSTALL FRONT FENDER MAIN SEAL LH

a.
B407827

Attach the 3 clips and 2 guides to install the front fender main seal LH.


Hide 53882H 6.INSTALL FRONT FENDER MAIN SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 9.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
B383432E02
2.508,4.093 2.743,4.321 0.235,0.228 10 *b 1.858,1.159 1.385,2.094 false 2.586,3.998 2.586,3.448 2.586,3.448 1.958,3.113 false 1.263,2.098 2.639,2.301 1.377,0.204 10 *a

Stop the wiper motor at the automatic stop position.

Text in Illustration
*a Wiper Arm Serrations
*b Wiper Pivot Serrations


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration.


d.
E157802E07
2.188,3.063 2.188,2.875 2.188,2.875 2.042,2.49 false 1.177,2.521 1.333,2.771 0.156,0.25 10 false A 2.115,3.063 2.458,3.313 0.344,0.25 10 false *a

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Text in Illustration
*a Moulding Edge

Standard Measurement:
Position Specified Condition
A 16.8 to 36.8 mm (0.661 to 1.45 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



Hide 10.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.
B383432E02
2.508,4.093 2.743,4.321 0.235,0.228 10 *b 1.858,1.159 1.385,2.094 false 2.586,3.998 2.586,3.448 2.586,3.448 1.958,3.113 false 1.263,2.098 2.639,2.301 1.377,0.204 10 *a

Stop the wiper motor at the automatic stop position.

Text in Illustration
*a Wiper Arm Serrations
*b Wiper Pivot Serrations


b.

Clean the wiper arm serration with a round file or equivalent.


c.

Clean the wiper pivot serration.


d.
E157803E07
2.188,2.792 2.188,2.698 2.188,2.698 2.042,2.49 false 2.115,2.781 2.396,3.01 0.281,0.229 10 false *a 0.146,2.417 0.344,2.646 0.198,0.229 10 false A

Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

Text in Illustration
*a Moulding Edge

Standard Measurement:
Position Specified Condition
A 20.0 to 40.0 mm (0.787 to 1.57 in.)


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Hold down the wiper arm hinge with your hand while tightening the nut.



e.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 85292B 11.INSTALL FRONT WIPER ARM HEAD CAP

a.

Attach the 3 claws and install the front wiper arm head cap.

HINT:

Use the same procedure for both front wiper arm head caps.