Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

This DTC is stored when a failure of the automatic light control sensor circuit is detected.

DTC Code DTC Detection Condition Trouble Area
B1244 When either condition below is met:
·

Malfunction of the automatic light control sensor.

·

Open or short in the light sensor circuit.


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU



WIRING DIAGRAM

E132905E13
5.563,3.406 6.781,3.635 1.219,0.229 10 false Main Body ECU 1.125,2.688 1.594,2.833 0.469,0.146 10 false CLTE 1.125,1.885 1.594,2.031 0.469,0.146 10 false CLTS 1.125,1.083 1.594,1.229 0.469,0.146 10 false CLTB 1.125,2.688 1.594,2.833 0.469,0.146 10 false CLTE 5.688,2.688 6.156,2.833 0.469,0.146 10 false CLTE 5.677,1.885 6.146,2.031 0.469,0.146 10 false CLTS 5.677,1.083 6.146,1.229 0.469,0.146 10 false CLTB 5.406,1.198 5.594,1.375 0.188,0.177 10 false 20 5.406,1.99 5.594,2.167 0.188,0.177 10 false 19 5.406,2.792 5.594,2.969 0.188,0.177 10 false 18 0.406,3.385 2.5,3.604 2.094,0.219 10 false Automatic Light Control Sensor 1.594,1.208 1.698,1.354 0.104,0.146 10 false 6 1.594,1.99 1.708,2.135 0.115,0.146 10 false 5 1.594,2.792 1.74,2.938 0.146,0.146 10 false 3 0.396,3.198 0.635,3.375 0.24,0.177 10 false F9 5.552,3.198 5.74,3.375 0.188,0.177 10 false E2

PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTC (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1244 is not output.




OK

NG

2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
a.

Operate the intelligent tester according to the display and select "Data List".

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate/min.: 0, max.: 99.99 Actual illumination rate is displayed -

OK:

Output illuminance is as shown in table above.




OK

REPLACE MAIN BODY ECU

NG

3.CHECK MAIN BODY ECU (LIGHT CONTROL SENSOR VOLTAGE)
3.CHECK MAIN BODY ECU (LIGHT CONTROL SENSOR VOLTAGE)
a.
U166026E01
0.194,0.033 2.480,0.380 2.286,0.347 10 Component with harness connected: (Main Body ECU) 0.479,1.015 0.669,1.166 0.190,0.150 10 E2 1.266,1.326 0.718,1.588 false 0.216,1.5 0.599,1.646 0.383,0.147 10 CLTB 2.376,1.614 2.759,1.761 0.383,0.147 10 CLTE 1.47,1.322 2.355,1.683 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E2-20 (CLTB) - E2-18 (CLTE) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

NG

REPLACE MAIN BODY ECU

4.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the E2 ECU connector.


U165936E01
0.036,0.018 2.372,0.361 2.336,0.343 10 Front view of wire harness connector: (to Main Body ECU) 0.036,2.21 2.372,2.724 2.336,0.514 10 Front view of wire harness connector: (to Automatic Light Control Sensor) 0.28,1.48 0.470,1.629 0.191,0.149 10 E2 0.28,3.867 0.470,4.016 0.191,0.149 10 F9 2.368,1.637 2.743,1.637 false 2.766,1.551 3.140,1.693 0.373,0.142 10 CLTB 2.766,1.849 3.140,1.991 0.373,0.142 10 CLTS 2.766,1.168 3.140,1.310 0.373,0.142 10 CLTE 2.255,4.088 2.629,4.230 0.373,0.142 10 CLTB 0.744,4.093 1.117,4.235 0.373,0.142 10 CLTS 0.744,3.904 1.117,4.046 0.373,0.142 10 CLTE 2.229,1.746 2.736,1.918 false 2.087,1.634 2.732,1.256 false 1.572,4.167 1.192,4.167 false 2.229,4.167 1.85,4.167 false 1.572,4.001 1.192,4.001 false

b.

Disconnect the F9 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-20 (CLTB) - F9-6 (CLTB) Always Below 1 Ω
E2-19 (CLTS) - F9-5 (CLTS)
E2-18 (CLTE) - F9-3 (CLTE)
E2-20 (CLTB) - Body ground Always 10 kΩ or higher
E2-19 (CLTS) - Body ground
E2-18 (CLTE) - Body ground




OK

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR