The headlight leveling ECU actuates the headlight leveling motors according to the vehicle conditions.
After replacing the headlight leveling ECU, initialization of the ECU is necessary (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).
Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Drive The Leveling Motor UP* | Headlight leveling motor upward operation | ON/OFF | ON: Move up
OFF: Stop |
| Drive The Leveling Motor DOWN* | Headlight leveling motor downward operation | ON/OFF | ON: Move down
OFF: Stop |
*: Perform the Active Test with the engine running and vehicle stopped.
Headlight leveling motors operate normally.
OK
NG
Disconnect the E109 headlight leveling ECU connector.
Disconnect the A54*1 or A58*2 headlight leveling motor connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E109-11 (LH+) - A54-8 (LHIG) | Always | Below 1 Ω |
| E109-18 (LHT) - A54-3 (LH T) | Always | Below 1 Ω |
| E109-24 (LH-) - A54-4 (LH E) | Always | Below 1 Ω |
| E109-11 (LH+) - Body ground | Always | 10 kΩ or higher |
| E109-18 (LHT) - Body ground | Always | 10 kΩ or higher |
| E109-24 (LH-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E109-10 (RH+) - A58-8 (RHIG) | Always | Below 1 Ω |
| E109-17 (RHT) - A58-3 (RH T) | Always | Below 1 Ω |
| E109-23 (RH-) - A58-4 (RH E) | Always | Below 1 Ω |
| E109-10 (RH+) - Body ground | Always | 10 kΩ or higher |
| E109-17 (RHT) - Body ground | Always | 10 kΩ or higher |
| E109-23 (RH-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the headlight unit (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>REMOVAL).
| *a | Component without harness connected
(Headlight Unit Assembly LH) |
*b | Component without harness connected
(Headlight Unit Assembly RH) |
| *c | Front view of wire harness connector
(to Headlight Leveling Motor LH) |
*d | Front view of wire harness connector
(to Headlight Leveling Motor RH) |
Disconnect the headlight leveling motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (LHIG) - 3 | Always | Below 1 Ω |
| 3 (LH T) - 2 | ||
| 4 (LH E) - 1 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (RHIG) - 3 | Always | Below 1 Ω |
| 3 (RH T) - 2 | ||
| 4 (RH E) - 1 |
OK
NG
Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>DISASSEMBLY).
Perform the Active Test of the leveling motors (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
Headlight leveling motors operate normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C