Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052855 LIGHTING (EXT) _0255811 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2417  Headlight Beam Level Control Motor LH Malfunction  B2418  Headlight Beam Level Control Motor RH Malfunction  


DESCRIPTION

The headlight leveling motor receives a signal from the headlight swivel ECU to operate. The headlight swivel ECU receives a signal indicating the operating conditions of the headlight leveling motor.

DTC Code DTC Detection Condition Trouble Area
B2417
·

Malfunction in the headlight leveling motor LH.

·

Open or short in the headlight leveling motor LH circuit.


·

Headlight swivel ECU assembly

·

Headlight unit assembly LH

·

Headlight leveling motor LH

·

Harness or connector


B2418
·

Malfunction in the headlight leveling motor RH.

·

Open or short in the headlight leveling motor RH circuit.


·

Headlight swivel ECU assembly

·

Headlight unit assembly RH

·

Headlight leveling motor RH

·

Harness or connector



WIRING DIAGRAM

E246613E04
0.208,0.896 1.177,1.219 0.969,0.323 10 false from IG NO. 4 Relay 2.281,0.885 2.688,1.177 0.406,0.292 10 false IG 2.031,0.802 2.396,1.052 0.365,0.25 10 false 15 1.333,1.052 2.25,1.406 0.917,0.354 10 false ECU-IG No.3 2.292,5.042 2.604,5.344 0.313,0.302 10 false E1 2.042,4.948 2.448,5.281 0.406,0.333 10 false 22 0.854,6.385 2.802,6.635 1.948,0.25 10 false : LIN Communication Line 3.573,2.052 3.896,2.323 0.323,0.271 10 false 27 3.219,2.156 3.656,2.396 0.438,0.24 10 false LH- 3.583,1.292 3.844,1.531 0.26,0.24 10 false 3 3.208,1.385 3.635,1.646 0.427,0.26 10 false LHT 3.573,1.583 3.896,1.885 0.323,0.302 10 false 30 3.219,1.74 3.667,2.031 0.448,0.292 10 false LH+ 4.385,2.052 4.958,2.323 0.573,0.271 10 false LH E 5.344,1.385 6.625,1.75 1.281,0.365 10 false Headlight Leveling Motor LH 4.365,2.74 6.604,2.99 2.24,0.25 10 false Headlight Unit Assembly LH 4.354,4.969 6.531,5.333 2.177,0.365 10 false Headlight Unit Assembly RH 2.083,6.031 4.719,6.375 2.635,0.344 10 false Headlight Swivel ECU Assembly 5.354,3.656 6.635,4.052 1.281,0.396 10 false Headlight Leveling Motor RH 4.385,1.292 4.854,1.542 0.469,0.25 10 false LHIG 4.385,1.594 4.854,1.865 0.469,0.271 10 false LH T 4.385,4.281 4.948,4.552 0.563,0.271 10 false RH E 4.385,3.521 4.938,3.781 0.552,0.26 10 false RHIG 4.385,3.823 5,4.115 0.615,0.292 10 false RH T 3.563,4.281 3.875,4.51 0.313,0.229 10 false 28 3.208,4.385 3.667,4.646 0.458,0.26 10 false RH- 3.573,3.531 3.865,3.771 0.292,0.24 10 false 4 3.208,3.635 3.604,3.896 0.396,0.26 10 false RHT 3.563,3.823 3.865,4.104 0.302,0.281 10 false 11 4.208,2.042 4.542,2.26 0.333,0.219 10 false 4 4.198,1.292 4.5,1.5 0.302,0.208 10 false 8 4.198,1.583 4.479,1.854 0.281,0.271 10 false 3 5.156,2.042 5.417,2.25 0.26,0.208 10 false 1 5.156,1.271 5.438,1.552 0.281,0.281 10 false 3 5.156,1.573 5.406,1.792 0.25,0.219 10 false 2 5.156,4.281 5.448,4.5 0.292,0.219 10 false 1 5.156,3.5 5.479,3.76 0.323,0.26 10 false 3 5.156,3.802 5.469,4.031 0.313,0.229 10 false 2 4.219,4.281 4.479,4.521 0.26,0.24 10 false 4 4.219,3.5 4.5,3.74 0.281,0.24 10 false 8 4.219,3.802 4.469,4.052 0.25,0.25 10 false 3 3.208,4 3.615,4.271 0.406,0.271 10 false RH+ 4.385,2.573 4.719,2.792 0.333,0.219 10 false A54 4.365,4.802 4.677,5.104 0.313,0.302 10 false A58 2.083,5.854 2.542,6.104 0.458,0.25 10 false E101

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After replacing the headlight swivel ECU, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2417 or B2418 output does not occur.




OK

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LEVELING MOTOR)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT LEVELING MOTOR)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

AFS
Tester Display Test Part Control Range Diagnostic Note
Drive The Leveling Motor UP* Headlight leveling motor upward operation ON/OFF ON: Move up
OFF: Stop
Drive The Leveling Motor DOWN* Headlight leveling motor downward operation ON/OFF ON: Move down
OFF: Stop

*: Perform the Active Test with the engine running and vehicle stopped.


OK:

Headlight leveling motors operate normally.




OK

3.CHECK HEADLIGHT LEVELING MOTOR

NG

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HEADLIGHT LEVELING MOTOR
a.

Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>DISASSEMBLY).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2417 or B2418 output does not occur.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U165787E01
0.054,0.036 0.238,0.218 0.184,0.182 10 *a 1.862,1.922 2.091,2.089 0.229,0.166 10 E1 1.603,1.545 1.84,1.955 false 1.613,0.517 1.985,0.686 0.372,0.170 10 E101 0.867,1.922 1.095,2.089 0.229,0.166 10 IG 0.884,1.905 0.56,1.537 false

Disconnect the headlight swivel ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E101-15 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E101-22 (E1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Headlight Swivel ECU Assembly)


OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT SWIVEL ECU ASSEMBLY - HEADLIGHT UNIT ASSEMBLY)
a.

Disconnect the E101 headlight swivel ECU connector.


b.

Disconnect the A54*1 or A58*2 headlight unit connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
E101-3 (LHT) - A54-8 (LHIG) Always Below 1 Ω
E101-30 (LH+) - A54-3 (LH T) Always Below 1 Ω
E101-27 (LH-) - A54-4 (LH E) Always Below 1 Ω
E101-3 (LHT) - Body ground Always 10 kΩ or higher
E101-30 (LH+) - Body ground Always 10 kΩ or higher
E101-27 (LH-) - Body ground Always 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
E101-4 (RHT) - A58-8 (RHIG) Always Below 1 Ω
E101-11 (RH+) - A58-3 (RH T) Always Below 1 Ω
E101-28 (RH-) - A58-4 (RH E) Always Below 1 Ω
E101-4 (RHT) - Body ground Always 10 kΩ or higher
E101-11 (RH+) - Body ground Always 10 kΩ or higher
E101-28 (RH-) - Body ground Always 10 kΩ or higher




OK

6.INSPECT HEADLIGHT UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT HEADLIGHT UNIT ASSEMBLY
a.

Remove the headlight unit (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>REMOVAL).

E246614E02
4.313,0.865 4.958,0.583 false 4.99,0.729 4.854,1.26 true 5.198,0.563 5.646,1.26 true 0.823,0.885 1.469,0.604 true 1.479,0.75 1.344,1.281 true 1.667,0.604 2.115,1.302 true 3.927,0.104 4.24,0.354 0.313,0.25 10 false *b 3.927,0.792 4.365,1.042 0.438,0.25 10 false RH E 5.604,1.302 6.042,1.552 0.438,0.25 10 false RH T 4.688,1.333 5.125,1.583 0.438,0.25 10 false RHIG 4.458,1.646 4.771,1.896 0.313,0.25 10 false *d 0.958,1.646 1.271,1.896 0.313,0.25 10 false *c 0.427,0.104 0.74,0.354 0.313,0.25 10 false *a 0.5,0.833 0.938,1.083 0.438,0.25 10 false LH E 2.01,1.333 2.448,1.583 0.438,0.25 10 false LH T 1.198,1.323 1.635,1.573 0.438,0.25 10 false LHIG

Text in Illustration
*a Component without harness connected
(Headlight Unit Assembly LH)
*b Component without harness connected
(Headlight Unit Assembly RH)
*c Front view of wire harness connector
(to Headlight Leveling Motor LH)
*d Front view of wire harness connector
(to Headlight Leveling Motor RH)


b.

Disconnect the headlight leveling motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
8 (LHIG) - 3 Always Below 1 Ω
3 (LH T) - 2
4 (LH E) - 1

for RH:
Tester Connection Condition Specified Condition
8 (RHIG) - 3 Always Below 1 Ω
3 (RH T) - 2
4 (RH E) - 1




OK

7.CHECK HEADLIGHT LEVELING MOTOR

NG

7.CHECK HEADLIGHT LEVELING MOTOR
a.

Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>DISASSEMBLY).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2417 or B2418 output does not occur.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

END (HEADLIGHT LEVELING MOTOR WAS DEFECTIVE)

B

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY

C

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY