The headlight leveling motor operates by receiving the signal from the headlight swivel ECU. The headlight swivel ECU detects the headlight leveling motor status using the signal from the headlight leveling motor.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2424 | ·
Malfunction in the headlight leveling motor LH. ·
Open or short in the headlight leveling motor LH communication circuit. |
·
Headlight swivel ECU assembly ·
Headlight unit assembly LH ·
Headlight leveling motor LH ·
Harness or connector |
| B2425 | ·
Malfunction in the headlight leveling motor RH. ·
Open or short in the headlight leveling motor RH communication circuit. |
·
Headlight swivel ECU assembly ·
Headlight unit assembly RH ·
Headlight leveling motor RH ·
Harness or connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After replacing the headlight swivel ECU, initialization of the ECU is necessary (except w/ Dynamic Headlight Auto Leveling) (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION).
Clear the DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2424 or B2425 output does not occur.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the headlight swivel ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E101-15 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E101-22 (E1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Headlight Swivel ECU Assembly) |
OK
NG
Disconnect the E101 headlight swivel ECU connector.
Disconnect the A54*1 or A58*2 headlight unit connector.
*1: for LH
*2: for RH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E101-3 (LHT) - A54-8 (LHIG) | Always | Below 1 Ω |
| E101-30 (LH+) - A54-3 (LH T) | Always | Below 1 Ω |
| E101-27 (LH-) - A54-4 (LH E) | Always | Below 1 Ω |
| E101-3 (LHT) - Body ground | Always | 10 kΩ or higher |
| E101-30 (LH+) - Body ground | Always | 10 kΩ or higher |
| E101-27 (LH-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E101-4 (RHT) - A58-8 (RHIG) | Always | Below 1 Ω |
| E101-11 (RH+) - A58-3 (RH T) | Always | Below 1 Ω |
| E101-28 (RH-) - A58-4 (RH E) | Always | Below 1 Ω |
| E101-4 (RHT) - Body ground | Always | 10 kΩ or higher |
| E101-11 (RH+) - Body ground | Always | 10 kΩ or higher |
| E101-28 (RH-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the headlight unit (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>REMOVAL).
| *a | Component without harness connected
(Headlight Unit Assembly LH) |
*b | Component without harness connected
(Headlight Unit Assembly RH) |
| *c | Front view of wire harness connector
(to Headlight Leveling Motor LH) |
*d | Front view of wire harness connector
(to Headlight Leveling Motor RH) |
Disconnect the headlight leveling motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (LHIG) - 3 | Always | Below 1 Ω |
| 3 (LH T) - 2 | ||
| 4 (LH E) - 1 |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (RHIG) - 3 | Always | Below 1 Ω |
| 3 (RH T) - 2 | ||
| 4 (RH E) - 1 |
OK
NG
Temporarily replace the headlight leveling motor with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for HID Headlight)>DISASSEMBLY).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2424 or B2425 output does not occur.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C